V/P clearance
Thread Starter
Teching In
Joined: Sep 2008
Posts: 45
Likes: 0
V/P clearance HEY PEOPLE NEW TO THE SITE. I bought a Lunati Camshaft. The Specs are
Advertised Duration (Int/Exh): 300/300
Duration @ .050 (Int/Exh): 242/242
Gross Valve Lift (Int/Exh): .595/.595
LSA/ICL: 112/108
Valve Lash (Int/Exh): Hyd/Hyd
RPM Range: 3500-6500
Part Number: 55009LUN
I Also bought LS1 heads ported and polished. these specs are:
2.02 intake and 1.60 EXHAUST
LS1 STAGE 3 PORTED HEADS
HEADS ARE PORTED. AND FLOWED @ 28" H2O
241 CASTINGS & 225 CC INTAKE PORTS
flowed on a Super Flow 600 Bench no pipe on a 202 valve.
Will i have piston to valve clearance?
Advertised Duration (Int/Exh): 300/300
Duration @ .050 (Int/Exh): 242/242
Gross Valve Lift (Int/Exh): .595/.595
LSA/ICL: 112/108
Valve Lash (Int/Exh): Hyd/Hyd
RPM Range: 3500-6500
Part Number: 55009LUN
I Also bought LS1 heads ported and polished. these specs are:
2.02 intake and 1.60 EXHAUST
LS1 STAGE 3 PORTED HEADS
HEADS ARE PORTED. AND FLOWED @ 28" H2O
241 CASTINGS & 225 CC INTAKE PORTS
flowed on a Super Flow 600 Bench no pipe on a 202 valve.
Will i have piston to valve clearance?
HEY PEOPLE NEW TO THE SITE. I bought a Lunati Camshaft. The Specs are
Advertised Duration (Int/Exh): 300/300
Duration @ .050 (Int/Exh): 242/242
Gross Valve Lift (Int/Exh): .595/.595
LSA/ICL: 112/108
Valve Lash (Int/Exh): Hyd/Hyd
RPM Range: 3500-6500
Part Number: 55009LUN
I Also bought LS1 heads ported and polished. these specs are:
2.02 intake and 1.60 EXHAUST
LS1 STAGE 3 PORTED HEADS
HEADS ARE PORTED. AND FLOWED @ 28" H2O
241 CASTINGS & 225 CC INTAKE PORTS
flowed on a Super Flow 600 Bench no pipe on a 202 valve.
Will i have piston to valve clearance?
Advertised Duration (Int/Exh): 300/300
Duration @ .050 (Int/Exh): 242/242
Gross Valve Lift (Int/Exh): .595/.595
LSA/ICL: 112/108
Valve Lash (Int/Exh): Hyd/Hyd
RPM Range: 3500-6500
Part Number: 55009LUN
I Also bought LS1 heads ported and polished. these specs are:
2.02 intake and 1.60 EXHAUST
LS1 STAGE 3 PORTED HEADS
HEADS ARE PORTED. AND FLOWED @ 28" H2O
241 CASTINGS & 225 CC INTAKE PORTS
flowed on a Super Flow 600 Bench no pipe on a 202 valve.
Will i have piston to valve clearance?
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
There's a lot that goes into calculating the piston to valve correctly. That being said my initial gut is it's going to be way to close. We've tested that lobe about 4 years ago and I doubt it will clear in this application without doing a little cutting 
__________________
Jason
Co-Owner, Texas Speed & Performance, Ltd.
2005 Twin Turbo C6
404cid Stroker, 67mm Twins
994rwhp/902lb ft @ 22 psi (mustang dyno) www.Texas-Speed.com
Jason
Co-Owner, Texas Speed & Performance, Ltd.
2005 Twin Turbo C6
404cid Stroker, 67mm Twins
994rwhp/902lb ft @ 22 psi (mustang dyno) www.Texas-Speed.com
Assuming you have a 346 I don't think it will clear safely at all even with OEM head gaskets but that is just me. Better measure first. 