Christmas in August
#1
TECH Apprentice
Thread Starter
iTrader: (2)
Join Date: Jun 2009
Location: Fredericksburg Va.
Posts: 334
Likes: 0
Received 0 Likes
on
0 Posts
Christmas in August
Here's a picture of some mods that I am looking forward to putting on. Problem is school has started and I am a teacher (no time!), still need to purchase some small but important items ($!!) and this is my DD. I am hoping to pull these things together in the next few weeks and get a run or two in before winter sets in.
http://www.facebook.com/group.php?gid=140336069313123
http://www.facebook.com/group.php?gid=140336069313123
#5
TECH Apprentice
Thread Starter
iTrader: (2)
Join Date: Jun 2009
Location: Fredericksburg Va.
Posts: 334
Likes: 0
Received 0 Likes
on
0 Posts
#6
12 Second Club
iTrader: (14)
Join Date: Jun 2007
Location: Renton, WA
Posts: 2,563
Likes: 0
Received 0 Likes
on
0 Posts
I don't have facebook so I don't know whats up. Damitt..
And that Boss cam is what Roger recommend for me. Just make sure you change your oil pump to a std. LS6 and you will be good with LS7 lifters and guides. Goodluck and I can't wait to see some numbers. Your heading in the same direction I was before deciding to go turbo.
And that Boss cam is what Roger recommend for me. Just make sure you change your oil pump to a std. LS6 and you will be good with LS7 lifters and guides. Goodluck and I can't wait to see some numbers. Your heading in the same direction I was before deciding to go turbo.
Last edited by DavidGXP; 08-28-2010 at 01:19 AM.
Trending Topics
#9
TECH Apprentice
Thread Starter
iTrader: (2)
Join Date: Jun 2009
Location: Fredericksburg Va.
Posts: 334
Likes: 0
Received 0 Likes
on
0 Posts
Christmas in August
true that! TEP trans with a 300mm input shaft, 7/8 chain and a 3.29 gear was installed last month. Oil pump, lifters, gaskets and cam conversion still to go ....and the cost of a good tune!! Plan on selling my ported intake, Hogan DP, TBS and diablo tuner to help cover the cost of the tune. Thanks for your input
#12
TECH Apprentice
Thread Starter
iTrader: (2)
Join Date: Jun 2009
Location: Fredericksburg Va.
Posts: 334
Likes: 0
Received 0 Likes
on
0 Posts
Christmas in August
Sorry guys, I should of included a parts list with my picture; LS1 intake, rockers/rods/springs, cam, DH header, Full wet kit (100 shot). I have received a few pms about some mods that I will be selling once they come off. Dids for those who have already pm me in order. I will reply to your pms on Sunday.
#14
TECH Apprentice
Thread Starter
iTrader: (2)
Join Date: Jun 2009
Location: Fredericksburg Va.
Posts: 334
Likes: 0
Received 0 Likes
on
0 Posts
Christmas in August
Engine and transmission comes out this Wed!! Engine will then be worked on after I get off of work, hoping to get it done within 3 weeks, then off to exhaust shop and to the tuner. Planning on posting some pics, dyno graph, track times and a high speed run.
#17
TECH Apprentice
Thread Starter
iTrader: (2)
Join Date: Jun 2009
Location: Fredericksburg Va.
Posts: 334
Likes: 0
Received 0 Likes
on
0 Posts
#20
TECH Apprentice
Thread Starter
iTrader: (2)
Join Date: Jun 2009
Location: Fredericksburg Va.
Posts: 334
Likes: 0
Received 0 Likes
on
0 Posts
no problem. Had a transmission guy test drive the car yesterday. He will be taking a look at a few things when the transmission comes out. Have a few more things to order; gaskets, header whistle flex tube and I'm thinking about trying to see if I can get a plate setup for the N20.