Secret to running in the low 13's
#1
TECH Regular
Thread Starter
Join Date: Sep 2010
Location: Kansas City MO
Posts: 428
Likes: 0
Received 0 Likes
on
0 Posts
Secret to running in the low 13's
I was wondering what it would take to run in the low 13 second range (13 flat) in our cars. I know headers, intake, 3 inch exhaust, CAI, tune, and what else? I have been redefining my goals for my car and was wondering how much further I need to go in order to meet my goal. And please don't comment on my 22's!! I know they are a restriction and slow me down! Obviously when I race, they will not be on there. So with that said, what else do I need to do in order to reach my goal?
#3
so. wait your telling me you cant hit low 13's now with those mods? i would have thought that those alone would have done it. i figure the headers are good for 20hp, cai for 5, dp and exhaust for about 5-8, and the tune should give another 10. so on the low end it would be 340 at the crank so close to 300 wheel hp. wow that 4 speed auto really kills our cars.
#5
TECH Resident
Join Date: May 2010
Location: Ontario, Canada
Posts: 803
Likes: 0
Received 0 Likes
on
0 Posts
so. wait your telling me you cant hit low 13's now with those mods? i would have thought that those alone would have done it. i figure the headers are good for 20hp, cai for 5, dp and exhaust for about 5-8, and the tune should give another 10. so on the low end it would be 340 at the crank so close to 300 wheel hp. wow that 4 speed auto really kills our cars.
Trending Topics
#8
TECH Apprentice
iTrader: (2)
Join Date: Jun 2009
Location: Fredericksburg Va.
Posts: 334
Likes: 0
Received 0 Likes
on
0 Posts
low 13's
I agree! esp if you add in a small shot!!! I would also invest some money in a shift kit, dogbone/polymount and a trans cooler to help your transmission survive the beating. I think Rossko ran a 12.99 with only a 100 shot and the backseat taken out.
#11
12 Second Club
iTrader: (14)
Join Date: Jun 2007
Location: Renton, WA
Posts: 2,563
Likes: 0
Received 0 Likes
on
0 Posts
1.8 60ft times.
13.00 is setting the bar pretty high with a little 5.3 pulling a car that weighs about 3800lbs and a trans that just shifts into 3rd when crossing.
Torque is the key combined with the proper gearing. It's all about acceleration.. Wich our engine and trans lacks! 2nd gear pull is a joke. Even with my intake, and when I had headers. 3.69 gears would help 2nd gear pull but would make 1st gear traction impossible
We might not be ET kings but we do put up some pretty good mph.
With 1.8 rockers and a raised shiftpoint (6100-6200) downpipe and and K&N hittitng 105-107mph isn't too hard to do.
Check this guy out...
https://ls1tech.com/forums/ls4-front...06-89-mph.html
and
https://ls1tech.com/forums/ls4-front...lly-hauls.html
These are the old school guys who have come close.. Before headers and intake manifold swaps.
13.00 is setting the bar pretty high with a little 5.3 pulling a car that weighs about 3800lbs and a trans that just shifts into 3rd when crossing.
Torque is the key combined with the proper gearing. It's all about acceleration.. Wich our engine and trans lacks! 2nd gear pull is a joke. Even with my intake, and when I had headers. 3.69 gears would help 2nd gear pull but would make 1st gear traction impossible
We might not be ET kings but we do put up some pretty good mph.
With 1.8 rockers and a raised shiftpoint (6100-6200) downpipe and and K&N hittitng 105-107mph isn't too hard to do.
Check this guy out...
https://ls1tech.com/forums/ls4-front...06-89-mph.html
and
https://ls1tech.com/forums/ls4-front...lly-hauls.html
These are the old school guys who have come close.. Before headers and intake manifold swaps.
#12
TECH Addict
iTrader: (15)
Join Date: Aug 2002
Location: 78°14′46″N 15°27′56″E
Posts: 2,419
Likes: 0
Received 6 Likes
on
5 Posts
I'd dump the speaker box and amps and yank out the back seat. Beyond that, I agree with the posts above: Throw all of the bolt-ons you can at it, and get a built trans from TEP with 3.69 gears and a taller tire.
#14
TECH Regular
Thread Starter
Join Date: Sep 2010
Location: Kansas City MO
Posts: 428
Likes: 0
Received 0 Likes
on
0 Posts
Also, I am going to wait til the tranny goes boom to start on that endeavor. So, with all that said, do you guys see it as a possibility? Is there anyway I can do it on street tires? So I should add a cutout, rockers, and what else to my list?
#15
TECH Resident
Join Date: May 2010
Location: Ontario, Canada
Posts: 803
Likes: 0
Received 0 Likes
on
0 Posts
headers
poly dogbone mount(helps alot)
intake(ls1)
you dont need the 3 inch exhaust if you get a cutout BEFORE the cat. put that cash towards slicks! lol keep the magnaflow catback
CAI
tune
cutout
rockers
ANY weight reduction possible.
poly dogbone mount(helps alot)
intake(ls1)
you dont need the 3 inch exhaust if you get a cutout BEFORE the cat. put that cash towards slicks! lol keep the magnaflow catback
CAI
tune
cutout
rockers
ANY weight reduction possible.
#16
TECH Fanatic
iTrader: (3)
Join Date: Aug 2009
Location: Orlando, FL
Posts: 1,392
Likes: 0
Received 0 Likes
on
0 Posts
so. wait your telling me you cant hit low 13's now with those mods? i would have thought that those alone would have done it. i figure the headers are good for 20hp, cai for 5, dp and exhaust for about 5-8, and the tune should give another 10. so on the low end it would be 340 at the crank so close to 300 wheel hp. wow that 4 speed auto really kills our cars.
#18
TECH Regular
Thread Starter
Join Date: Sep 2010
Location: Kansas City MO
Posts: 428
Likes: 0
Received 0 Likes
on
0 Posts
1.8 60ft times.
13.00 is setting the bar pretty high with a little 5.3 pulling a car that weighs about 3800lbs and a trans that just shifts into 3rd when crossing.
Torque is the key combined with the proper gearing. It's all about acceleration.. Wich our engine and trans lacks! 2nd gear pull is a joke. Even with my intake, and when I had headers. 3.69 gears would help 2nd gear pull but would make 1st gear traction impossible
We might not be ET kings but we do put up some pretty good mph.
With 1.8 rockers and a raised shiftpoint (6100-6200) downpipe and and K&N hittitng 105-107mph isn't too hard to do.
Check this guy out...
https://ls1tech.com/forums/ls4-front...06-89-mph.html
and
https://ls1tech.com/forums/ls4-front...lly-hauls.html
These are the old school guys who have come close.. Before headers and intake manifold swaps.
13.00 is setting the bar pretty high with a little 5.3 pulling a car that weighs about 3800lbs and a trans that just shifts into 3rd when crossing.
Torque is the key combined with the proper gearing. It's all about acceleration.. Wich our engine and trans lacks! 2nd gear pull is a joke. Even with my intake, and when I had headers. 3.69 gears would help 2nd gear pull but would make 1st gear traction impossible
We might not be ET kings but we do put up some pretty good mph.
With 1.8 rockers and a raised shiftpoint (6100-6200) downpipe and and K&N hittitng 105-107mph isn't too hard to do.
Check this guy out...
https://ls1tech.com/forums/ls4-front...06-89-mph.html
and
https://ls1tech.com/forums/ls4-front...lly-hauls.html
These are the old school guys who have come close.. Before headers and intake manifold swaps.