Garage sale!!!!!!!!!!!!!!!look!!!!!!!!!!!
02-02-2009, 11:03 PM
#1
Staging Lane
Thread Starter
iTrader: (30)
Join Date: Aug 2008
Location: BFE, CA
Posts: 81
Likes: 0
Received 0 Likes
on
0 Posts
Garage sale!!!!!!!!!!!!!!!look!!!!!!!!!!! Dart ported heads. They are assembled with rev stainless race valves and AFR 8019 valve springs. These have 0 miles on them since freshening. I bought these from a local guy and put them on my old 402 combo witch put down 564 at the tires, I will try to round up the old dyno sheet. They flowed somewhere in the 320 cfm range.
2.055 intake
1.60 exhaust
62cc chambers
I am looking for $1500 shipped for these and if you are using Paypal please add the 3%.
Patriot extreme valvesprings NewThese were installed but never ran $250 shipped
Caddy racing lifters (500 miles)- $150
Comp cams 242 242 .610 .610 on a 112 - $250 shipped
Comp cams 248 240 .637 .615 on a 112 - $250 shipped
Thunder racing 7.4 pushrods - $75 SOLD
NX fuel accumulator - $50
NOS -6x-6x-8 Y - $30
-4 feed line - $50
Walbro 255 in tank 100 miles- $90
MSD pill style window switch - $30
STOCK FBODY PARTS
Rockers with stands and bolts 35k miles - $40
853 heads complete - $100
perimiter heads - $75
perimiter valve covers - $20
Pass. side Ttop - $50
Pass. side T/A door complete with glass and window motor - $100
LS1 rear calipers w/ brackets - $50
WS6 cat back - $50
6.0 crank - $75
Make an offer on the rest
Drivers side door glass
M6 steering column
A4 steering column
A4 shifter
A4 trans crossmember
98' LS1 exhaust manifolds
Camaro rear view mirror
Camaro drivers air bag
LQ4 pistons and rods
Kmember
lower motor mount stands
I am open to trades and will not ship the big items.
Located in 92274
I will take pics of whatever you want, just let me know.
2.055 intake
1.60 exhaust
62cc chambers
I am looking for $1500 shipped for these and if you are using Paypal please add the 3%.
Patriot extreme valvesprings NewThese were installed but never ran $250 shipped
Caddy racing lifters (500 miles)- $150
Comp cams 242 242 .610 .610 on a 112 - $250 shipped
Comp cams 248 240 .637 .615 on a 112 - $250 shipped
Thunder racing 7.4 pushrods - $75 SOLD
NX fuel accumulator - $50
NOS -6x-6x-8 Y - $30
-4 feed line - $50
Walbro 255 in tank 100 miles- $90
MSD pill style window switch - $30
STOCK FBODY PARTS
Rockers with stands and bolts 35k miles - $40
853 heads complete - $100
perimiter heads - $75
perimiter valve covers - $20
Pass. side Ttop - $50
Pass. side T/A door complete with glass and window motor - $100
LS1 rear calipers w/ brackets - $50
WS6 cat back - $50
6.0 crank - $75
Make an offer on the rest
Drivers side door glass
M6 steering column
A4 steering column
A4 shifter
A4 trans crossmember
98' LS1 exhaust manifolds
Camaro rear view mirror
Camaro drivers air bag
LQ4 pistons and rods
Kmember
lower motor mount stands
I am open to trades and will not ship the big items.
Located in 92274
I will take pics of whatever you want, just let me know.
Last edited by addicted2myWS6; 02-08-2009 at 08:11 PM.
Trending Topics
02-07-2009, 02:09 PM
#10
Dart ported heads. They are assembled with rev stainless race valves and AFR 8019 valve springs. These have 0 miles on them since freshening. I bought these from a local guy and put them on my old 402 combo witch put down 564 at the tires, I will try to round up the old dyno sheet. They flowed somewhere in the 320 cfm range.
2.055 intake
1.60 exhaust
62cc chambers
I am looking for $1500 shipped for these and if you are using Paypal please add the 3%.
Patriot extreme valvesprings NewThese were installed but never ran $250
Caddy racing lifters (500 miles)- $150
Comp cams 242 242 .610 .610 on a 112 - $250
Comp cams 248 240 .637 .615 on a 112 - $250
2.055 intake
1.60 exhaust
62cc chambers
I am looking for $1500 shipped for these and if you are using Paypal please add the 3%.
Patriot extreme valvesprings NewThese were installed but never ran $250
Caddy racing lifters (500 miles)- $150
Comp cams 242 242 .610 .610 on a 112 - $250
Comp cams 248 240 .637 .615 on a 112 - $250
Did you find the dyno sheet? Also, who did the porting? hand or C&C
02-07-2009, 02:29 PM
#11
Staging Lane
Thread Starter
iTrader: (30)
Join Date: Aug 2008
Location: BFE, CA
Posts: 81
Likes: 0
Received 0 Likes
on
0 Posts
I havent found the dyno sheet, if sombody is truly interested I will go down to the dyno and have the reprint it.
The heads are hand ported and I have no clue who ported them. I havent had them flowed either. I am going by what the original owner told me and I have had no reason to doubt him with the numbers they made.
02-07-2009, 04:40 PM
#12
I was running the Comp cams 248 240 .637 .615 on a 112 with 12:1 compression and an LS6 intake.
I havent found the dyno sheet, if sombody is truly interested I will go down to the dyno and have the reprint it.
The heads are hand ported and I have no clue who ported them. I havent had them flowed either. I am going by what the original owner told me and I have had no reason to doubt him with the numbers they made.
I havent found the dyno sheet, if sombody is truly interested I will go down to the dyno and have the reprint it.
The heads are hand ported and I have no clue who ported them. I havent had them flowed either. I am going by what the original owner told me and I have had no reason to doubt him with the numbers they made.
sounds like you have a pretty killer heads/cam 402. Sounds like close to 580whp with a nice ported fast on there.
I honestly dont think iv seen a streetable pump gas 402 with those kind of whp numbers.
you have any videos? curious to hear how it sounded
where exactly in cali are you?
02-07-2009, 04:48 PM
#13
Staging Lane
Thread Starter
iTrader: (30)
Join Date: Aug 2008
Location: BFE, CA
Posts: 81
Likes: 0
Received 0 Likes
on
0 Posts
I am switching combos, because I spun a bearing and I need a set of heads with a 70cc chamber. I also now have a killer intake set up and I believe the cam would be crap with my new combo. It was spec'ed around the shitty ls6 intake and with the new setup, I am getting one for the new motor.
It might have made more power with a good intake but I have know idea, I think it was just setup perfectly.
As far as the dyno sheet, I called them up and they are going to print out my sheets and bring them to me one day this week.
It might have made more power with a good intake but I have know idea, I think it was just setup perfectly.
As far as the dyno sheet, I called them up and they are going to print out my sheets and bring them to me one day this week.
02-07-2009, 04:53 PM
#14
I am switching combos, because I spun a bearing and I need a set of heads with a 70cc chamber. I also now have a killer intake set up and I believe the cam would be crap with my new combo. It was spec'ed around the shitty ls6 intake and with the new setup, I am getting one for the new motor.
It might have made more power with a good intake but I have know idea, I think it was just setup perfectly.
As far as the dyno sheet, I called them up and they are going to print out my sheets and bring them to me one day this week.
It might have made more power with a good intake but I have know idea, I think it was just setup perfectly.
As far as the dyno sheet, I called them up and they are going to print out my sheets and bring them to me one day this week.
where exactly are you located in cali? near san jose?
02-07-2009, 05:00 PM
#15
Staging Lane
Thread Starter
iTrader: (30)
Join Date: Aug 2008
Location: BFE, CA
Posts: 81
Likes: 0
Received 0 Likes
on
0 Posts
It is going to be a long rod 370. I got a good deal on a set of pistons, but they have a 10cc dome on them and with these heads I will have about 13:1 compression and I want to keep it below 12.5:1 without running a .070 thick gasket.
I live about an hour away from riverside.
I live about an hour away from riverside.
02-07-2009, 06:13 PM
#16
It is going to be a long rod 370. I got a good deal on a set of pistons, but they have a 10cc dome on them and with these heads I will have about 13:1 compression and I want to keep it below 12.5:1 without running a .070 thick gasket.
I live about an hour away from riverside.
I live about an hour away from riverside.
How much for the heads picked up?
02-07-2009, 06:42 PM
#18
Staging Lane
Thread Starter
iTrader: (30)
Join Date: Aug 2008
Location: BFE, CA
Posts: 81
Likes: 0
Received 0 Likes
on
0 Posts
http://profile.myspace.com/index.cfm...endID=84023819
Check out that profile on myspace. The primer gray car is now charcoal grey and there are videos of it on there. All of the videos are with the 402 and that heads cam.
Check out that profile on myspace. The primer gray car is now charcoal grey and there are videos of it on there. All of the videos are with the 402 and that heads cam.
02-07-2009, 07:02 PM
#20
myspace is on private and i couldnt find you on fquick.
possible package price on both? just been lurking for heads/cam for awhile to see whats out there. My buddy is heading to cali at the end of the month and thought about maybe workign something out.
possible package price on both? just been lurking for heads/cam for awhile to see whats out there. My buddy is heading to cali at the end of the month and thought about maybe workign something out.