Procharged '01 Z28 part out
07-09-2009, 10:40 PM
#1
11 Second Club
Thread Starter
iTrader: (20)
Join Date: Mar 2005
Location: J.C.
Posts: 575
Likes: 0
Received 0 Likes
on
0 Posts
Procharged '01 Z28 part out I listed the whole car for sale but it didnt go so i'll see if I can part it out. If I can for sure get buyers on the motor and trans/converter(4l80e f-body swap) then i'll pull them out of the car.
Motor- I have a tsp built 370 with the stock crank, Scat H-beam rods, Mahle flat-tops (-1cc valve reliefs), Prc 2.5 Ls6 heads, Mls .040 gaskets, Ms4 cam, and the Fast 92/92 combo. I have around 10k miles on this and would like$4,800 intake to oil pan.
Trans- Is a 4l80e that has all new solenoids in it, red clutch's in 1st-3rd and blue clutch's in 4th. A few of the hard parts were replaced as well. A Pro Yank 3600rpm stall, yank 4l80e cross member, frost 80e adapter. I have around 2k miles on this and would like $2,200 for the setup.
So if I get buyers for both motor and the trans setup i'll yank them out of the car. I would like to keep it to being picked up as well, or the buyer can pay for & setup shipping and I can try to help.
Thanks
Motor- I have a tsp built 370 with the stock crank, Scat H-beam rods, Mahle flat-tops (-1cc valve reliefs), Prc 2.5 Ls6 heads, Mls .040 gaskets, Ms4 cam, and the Fast 92/92 combo. I have around 10k miles on this and would like$4,800 intake to oil pan.
Trans- Is a 4l80e that has all new solenoids in it, red clutch's in 1st-3rd and blue clutch's in 4th. A few of the hard parts were replaced as well. A Pro Yank 3600rpm stall, yank 4l80e cross member, frost 80e adapter. I have around 2k miles on this and would like $2,200 for the setup.
So if I get buyers for both motor and the trans setup i'll yank them out of the car. I would like to keep it to being picked up as well, or the buyer can pay for & setup shipping and I can try to help.
Thanks
07-09-2009, 11:56 PM
#3
TECH Fanatic
iTrader: (35)
Join Date: Aug 2004
Location: Paramount CA
Posts: 1,016
Likes: 0
Received 0 Likes
on
0 Posts
any interest in parting out the heads and intake/tb combo?
or would consider a trade for a cammed LS1 longblock with all new gaskets, timing chain, lifters, oil pump, etc? I could trade complete fromintake to oil pan as well...
or would consider a trade for a cammed LS1 longblock with all new gaskets, timing chain, lifters, oil pump, etc? I could trade complete fromintake to oil pan as well...
Trending Topics
07-10-2009, 09:54 AM
#9
11 Second Club
Thread Starter
iTrader: (20)
Join Date: Mar 2005
Location: J.C.
Posts: 575
Likes: 0
Received 0 Likes
on
0 Posts
As of right now there is a simi local guy that is thinking about it. I told him 4k for it all.
I have a D1sc with a fmic setup and 8rib upgrade. I also have an AIS meth kit to go with it. You would need a fan setup as I'm just running with one stock one cut out. And a crank pulley as well as I'm using a march underdrive that 9sectruck and I drilled and tapped to use with a spacer.
I have a D1sc with a fmic setup and 8rib upgrade. I also have an AIS meth kit to go with it. You would need a fan setup as I'm just running with one stock one cut out. And a crank pulley as well as I'm using a march underdrive that 9sectruck and I drilled and tapped to use with a spacer.
07-15-2009, 07:35 PM
#19
11 Second Club
Thread Starter
iTrader: (20)
Join Date: Mar 2005
Location: J.C.
Posts: 575
Likes: 0
Received 0 Likes
on
0 Posts
I'm pulling the procharger off and just putting the car back on ebay. I had a "I'll take it" on the trans setup the night I posted but then never heard anything out of him again so... If you want the charger setup it will still be for sale.
Thanks,
Devon
Thanks,
Devon
