Cometic Head Gaskets LS1 3.910 .027"
03-09-2005, 09:42 PM
#1
TECH Apprentice
Thread Starter
iTrader: (18)
Join Date: May 2002
Location: Aurora, CO
Posts: 323
Likes: 0
Received 0 Likes
on
0 Posts
Cometic Head Gaskets LS1 3.910 .027" Selling BRAND NEW in package Cometic head gaskets. Were custom ordered from cometic.
Asking $150 obo shipped. Paypal payments only.
For LS1
Bore: 3.910
Thickness: .027" (will raise compression)
Pictures:
Brian
Asking $150 obo shipped. Paypal payments only.
For LS1
Bore: 3.910
Thickness: .027" (will raise compression)
Pictures:
Brian
Last edited by 2K2CamaroSS; 03-09-2005 at 10:59 PM.
03-11-2005, 02:54 PM
#4
10 Second Club
iTrader: (5)
Join Date: Nov 2001
Location: Cali/Bay Area
Posts: 3,412
Likes: 0
Received 0 Likes
on
0 Posts
Are these as thin as they go for an MLS gasket? Was going to call Cometic to see if they had .025" but these will do fine also. I need to transfer money into PayPal...
Dan
Dan
Trending Topics
03-12-2005, 12:02 AM
#8
Originally Posted by DanZ28
PM sent back!
Thanks for the heads up Beast96Z! My pistons are +.008 below the deck, plus valve reliefs, so I am good to go
Dan
Thanks for the heads up Beast96Z! My pistons are +.008 below the deck, plus valve reliefs, so I am good to go
Dan
03-12-2005, 01:09 PM
#9
10 Second Club
iTrader: (5)
Join Date: Nov 2001
Location: Cali/Bay Area
Posts: 3,412
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Beast96Z
Sounds like it'll be just the gasket for you. You usaully don't see many LS-1's with a piston below deck.
Dan
03-12-2005, 08:52 PM
#10
Staging Lane
Join Date: Feb 2004
Posts: 76
Likes: 0
Received 0 Likes
on
0 Posts
hmmm about that bore size. I have a 3.905 bore with a shaved block with pistons .010 out of the hole and forged pistons with 7cc valve reliefs for 2.055 1.60 valves. 98 heads, o-ringed, with large chambers. what do you think? I am looking for greator compression.
03-13-2005, 12:59 AM
#11
10 Second Club
iTrader: (5)
Join Date: Nov 2001
Location: Cali/Bay Area
Posts: 3,412
Likes: 0
Received 0 Likes
on
0 Posts
Your quench would be only .017", not much to go there with 2.055 valves even with 7 cc reliefs. What size chambers are your heads? how much milled? These gaskets put me at 11.0 CR with 62cc chambers and I get a .035" quench, which is about perfect for what I want...
Dan
Dan
03-13-2005, 06:22 AM
#12
Staging Lane
Join Date: Feb 2004
Posts: 76
Likes: 0
Received 0 Likes
on
0 Posts
I believe by looking at them and not actually measuring them that the chambers are stock cc. save for the new valve seats and larger valves. Heads were one of 3 sets origonally built for a turbo project so I am sure they are large chamber and not less than stock. Heads have only minor clean up and I had o-rings installed. Will these gaskets be compatalbe with o-rings?
I think 98 heads came with 67.67 chambers?
I think 98 heads came with 67.67 chambers?
Last edited by denton needham; 03-13-2005 at 06:33 AM.
