Ebay Headers Are Here
02-15-2009, 08:22 PM
#23
TECH Apprentice
Thread Starter
Got a little further today. Y2KFirehawk came over and gave me a hand 
. Got the manifolds out (no broken bolts yay) as well as getting the new driver side motor mount in. Tried putting the driver side header in through the top with no luck. Needs to go in from the bottom, so the car has to go up much higher.
To those debating whether to do motor mounts or not, I definitely recommend it. The mount didn't look bad in the car but found it was cracking and scrunched up in a few places. The worst part is trying to get the rivets out.
. Got the manifolds out (no broken bolts yay) as well as getting the new driver side motor mount in. Tried putting the driver side header in through the top with no luck. Needs to go in from the bottom, so the car has to go up much higher.To those debating whether to do motor mounts or not, I definitely recommend it. The mount didn't look bad in the car but found it was cracking and scrunched up in a few places. The worst part is trying to get the rivets out.
02-15-2009, 08:32 PM
#24
LT installs are such a PITA. Been there done that a few times and I hope to never do them again! Right now with my AIR/EGR out along with the A/C lines its substantially easier but still need to use a rubber mallet to "force" the passengers side up through. Good luck man and post some vids when its done I'd like to hear it.
02-15-2009, 10:04 PM
#26
Teching In
Join Date: Feb 2009
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
i wouldnt of purchased those if i was you. i did and was a pain in the ***. had major fitment issues. the driver side header will hit the steering knuckle and the fitment of the y pipe is gonna raddle. best way to install is get the car jacked up real high so u can tilt the header up.
02-15-2009, 10:25 PM
#27
Sorry I couldn't make it out, Chris. If I wasn't on call at work I'd be there. Got a call this AM and it made me afraid to leave the house.
Since the first primary is different then my super comps it doesnt surprise me you need to go through the bottom. Just get some good jack stands and you'll be okay.
When will you be operating again?
Since the first primary is different then my super comps it doesnt surprise me you need to go through the bottom. Just get some good jack stands and you'll be okay.
When will you be operating again?
02-15-2009, 10:45 PM
#28
Staging Lane
Join Date: Feb 2009
Location: st jo mo
Posts: 80
Likes: 0
Received 0 Likes
on
0 Posts
i got my lpps for 10 more bucks than those. but the lpps have a few fitment issues as well hits the steering shaft and the k member as well as the oil filter issue iv had had on mine, but for the money i think the lpps would have been a way better deal. has every one had the issue with the pass side hitting below the heater core?
02-16-2009, 10:24 AM
#31
You need a 3G WWAN card, Harner 
The ironic part of removing the passenger side manifold was that the manifold bolts weren't the hardest task, (after planning your attack route) it was all the ancillary stuff! (i.e. EGR tube at the collector, alternator support bracket attached to the front manifold bolt, O2 Sensor.)
The driver side engine mount wasn't too hard to get out, (which again, we anticipated that to be the "hard" part) it was getting the silly rivets out and actually opening the "clamshell" that took the longest
The ironic part of removing the passenger side manifold was that the manifold bolts weren't the hardest task, (after planning your attack route) it was all the ancillary stuff! (i.e. EGR tube at the collector, alternator support bracket attached to the front manifold bolt, O2 Sensor.)
The driver side engine mount wasn't too hard to get out, (which again, we anticipated that to be the "hard" part) it was getting the silly rivets out and actually opening the "clamshell" that took the longest
Last edited by Y2KFirehawk; 02-17-2009 at 01:20 PM.
02-16-2009, 12:04 PM
#32
Launching!
Join Date: Feb 2009
Posts: 201
Likes: 0
Received 0 Likes
on
0 Posts
i had bought the same ones and changed my mind and got pacesetters with Y pipe for 500. hope they work out good, i spoke to the guy and said that they were never tested on the car so i had changed my mind on them. let me know how they work.
02-16-2009, 07:16 PM
#33
TECH Apprentice
Thread Starter
i wouldnt of purchased those if i was you. i did and was a pain in the ***. had major fitment issues. the driver side header will hit the steering knuckle and the fitment of the y pipe is gonna raddle. best way to install is get the car jacked up real high so u can tilt the header up.
For clarification, here are LPPs:
Here are the ones I bought:
Sorry I couldn't make it out, Chris. If I wasn't on call at work I'd be there. Got a call this AM and it made me afraid to leave the house.
Since the first primary is different then my super comps it doesnt surprise me you need to go through the bottom. Just get some good jack stands and you'll be okay.
When will you be operating again?
Since the first primary is different then my super comps it doesnt surprise me you need to go through the bottom. Just get some good jack stands and you'll be okay.
When will you be operating again?
02-17-2009, 01:30 AM
#36
TECH Fanatic
iTrader: (4)
Join Date: Feb 2008
Location: S.W. Missouri
Posts: 1,291
Likes: 0
Received 0 Likes
on
0 Posts
Hopefully they fit good, i couldn't be happier with my PS LTs & Ory, they don't hit the steering cupler, oil filter ect., the only issue is they touch on the pass side, i'm thinking its the frame rail, but its been awhile.
02-17-2009, 11:33 AM
#39
Teching In
Join Date: Feb 2009
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
[QUOTE=spudnick3119;11067200]Are you sure you bought these and are not confusing them with LPPs? They only came out about a week ago and AFAIK, I'm the first on here to buy them. I've read that the LPPs do need some modifying on some cars to fit correctly but nothing major.
to be honest i coudnt tell you i bought them about 7 months ago so i could be wrong. well anyways gl with the install.
to be honest i coudnt tell you i bought them about 7 months ago so i could be wrong. well anyways gl with the install.
