header rubbing on steering knuckle help
#1
On The Tree
Thread Starter
Join Date: Apr 2009
Location: canton MI
Posts: 125
Likes: 0
Received 0 Likes
on
0 Posts
header rubbing on steering knuckle help
I just installed pace setter long tubes on my 95 and 3 of the primaries are rubbing bad on the steering knuckle! anybody else have this problem? any way to fix it?
#4
TECH Apprentice
iTrader: (3)
Join Date: Jul 2008
Location: Morinville, Alberta, Canada
Posts: 374
Likes: 0
Received 0 Likes
on
0 Posts
Mine rubbed slightly, i left it and drove around with it like that and it stopped rubbing after about 2 days. Haha, probably not the best idea, but it worked and doesnt rub at all anymore.
Trending Topics
#10
TECH Regular
iTrader: (1)
Join Date: Feb 2009
Location: PSL, FL
Posts: 399
Likes: 0
Received 0 Likes
on
0 Posts
They also have a rag joint eliminator you can use...basically just a round piece of aluminum with four holes drilled in it to take the place of the rag joint. I am eventually going to make my own steering shaft using some "flaming river" knuckles or equivalent and a cut to length splined shaft.
Anyway, it may also be your motor mounts are sagging...I would make sure they are new/replaced before doing any grinding/cutting/modifying. If you must modify though if your mounts are fine, you can grind some yes. Try and take as little as possible and make sure you smooth everything out leaving no sharp points or valley for a crack to start on. I wouldn't take much. If you have to take a lot, dent in the primaries or try and cut/weld them back some for clearance.
I had the same issue with some fitting issues on the Ebay style I bought and had to be patient and do some modifying. it helps having the right tools around...grinders, welder, cut off wheels, etc.
I wouldn't just let it rub though as it could do more than just dent in the primary as it clearances itself. If it is hitting hard enough for you to feel in the wheel, it could bend the primaries back and forth under the pressure of you turning your wheel and eventually put a crack in the exhaust primary. Not to mention it it probably not the best thing in the world to have all the heat of the combustion chamber right out of the head resting hard against your steering joint.
Anyway, it may also be your motor mounts are sagging...I would make sure they are new/replaced before doing any grinding/cutting/modifying. If you must modify though if your mounts are fine, you can grind some yes. Try and take as little as possible and make sure you smooth everything out leaving no sharp points or valley for a crack to start on. I wouldn't take much. If you have to take a lot, dent in the primaries or try and cut/weld them back some for clearance.
I had the same issue with some fitting issues on the Ebay style I bought and had to be patient and do some modifying. it helps having the right tools around...grinders, welder, cut off wheels, etc.
I wouldn't just let it rub though as it could do more than just dent in the primary as it clearances itself. If it is hitting hard enough for you to feel in the wheel, it could bend the primaries back and forth under the pressure of you turning your wheel and eventually put a crack in the exhaust primary. Not to mention it it probably not the best thing in the world to have all the heat of the combustion chamber right out of the head resting hard against your steering joint.
#11
12 Second Club
Join Date: Jun 2005
Location: Warner Robins Ga
Posts: 509
Likes: 0
Received 0 Likes
on
0 Posts
I loosened the bolt on the shaft near where it was hitting and extend it till it cleared. Mine was stuck so I had to use a hammer and a punch to get it to move.
#12
On The Tree
Thread Starter
Join Date: Apr 2009
Location: canton MI
Posts: 125
Likes: 0
Received 0 Likes
on
0 Posts
ok so i adjusted the linkage as far as it would go and it still rubbed where it connects at the top on the last primary. So i grinded it down a lot and it still rubbing im scared to grind it down anymore than i already have. Is there anybody who sells ones that are modified for clearance?
#15
TECH Regular
iTrader: (1)
Join Date: Feb 2009
Location: PSL, FL
Posts: 399
Likes: 0
Received 0 Likes
on
0 Posts
ok so i adjusted the linkage as far as it would go and it still rubbed where it connects at the top on the last primary. So i grinded it down a lot and it still rubbing im scared to grind it down anymore than i already have. Is there anybody who sells ones that are modified for clearance?
#16
On The Tree
iTrader: (1)
Join Date: Nov 2008
Location: Jamesburg, NJ
Posts: 170
Likes: 0
Received 0 Likes
on
0 Posts
The shaft will move (side to side). Under your dash, remove the bolts holding the rubber boot on. The holes can be drilled out slightly larger to provide a bit of movement to the driver's side wheel. I did this for my headers and all is fine.
I'm also using a rag joint eliminator and a modified LT1 shaft. The plastic pins were melted out, and the shaft was lengthened and then welded up solid. You may only need to move yours though. There's a good 1/4 movement...just make sure the top and bottom bolts are loosened up to all the shaft to slide on the mounting points.
I'm also using a rag joint eliminator and a modified LT1 shaft. The plastic pins were melted out, and the shaft was lengthened and then welded up solid. You may only need to move yours though. There's a good 1/4 movement...just make sure the top and bottom bolts are loosened up to all the shaft to slide on the mounting points.
#18
TECH Enthusiast
iTrader: (9)
Join Date: May 2007
Location: san jose, ca
Posts: 505
Likes: 0
Received 0 Likes
on
0 Posts
The shaft will move (side to side). Under your dash, remove the bolts holding the rubber boot on. The holes can be drilled out slightly larger to provide a bit of movement to the driver's side wheel. I did this for my headers and all is fine.
I'm also using a rag joint eliminator and a modified LT1 shaft. The plastic pins were melted out, and the shaft was lengthened and then welded up solid. You may only need to move yours though. There's a good 1/4 movement...just make sure the top and bottom bolts are loosened up to all the shaft to slide on the mounting points.
I'm also using a rag joint eliminator and a modified LT1 shaft. The plastic pins were melted out, and the shaft was lengthened and then welded up solid. You may only need to move yours though. There's a good 1/4 movement...just make sure the top and bottom bolts are loosened up to all the shaft to slide on the mounting points.
#19
On The Tree
Thread Starter
Join Date: Apr 2009
Location: canton MI
Posts: 125
Likes: 0
Received 0 Likes
on
0 Posts
i found out that most of the rubbing was due to the bolt that holds the top of the knuckle to the shaft. I ground down the head and the bottom of the bolt and it is much better but the whole knuckle is still rubbing the primaries a little. Odly enought the safety loops arent rubbing anything. its the middle shaft that is rubbing. Ill try to move the steering column to the side though if i can move it 1/8 of an in it would be perfectly clear of all obsticles. Thanks for the advice.