MattSapp95_T/A

iTrader: (35)

Yea for sure! I was worried that I would be waiting forever for the LT1 stuff to sell but It went faster than I could ship it..lol

I have the engine bay painted I will post some pics up shortly...

Matt

MattSapp95_T/A

iTrader: (35)

joelster

Looks sweet!

MattSapp95_T/A

iTrader: (35)

Thanks bud its getting there slowly but surely

SPOT ME 3

iTrader: (1)

Looking great Matt! Nice Avalanche too!

1961ba427

iTrader: (26)

Looking good. Which k-member is that? LS or LT? If it's LTx, what motor mounts are those? I know the LT1 stuff went fast, I ended up with your 1.7 rockers even though I didn't buy them from you. LOL The other buyer swapped plans.

MattSapp95_T/A

iTrader: (35)

Thanks!! The Avalanche makes a great tow vehicle too..lol

Its a PA Racing K member and A arms for LSX mounts...

Yea I literally couldn't keep up with shipping it fell in the middle of finals it was crazy....

Those 1.7 rockers were literally brand new...made 3 dyno pulls and a few short trips around the block....hope they work out good for you!!! Yea I think he is building a new motor and going 1.6s...

Matt

merim123

iTrader: (11)

matt are you spraying in your garage? what are you using for product and air compressor since I don't see one in the pics anywhere...

scj

iTrader: (89)

I have PA racing k member that i had my lt1 on, and i'm doing the ls swap, it looks to be about the same but with different mounts bolted to it. any idea?

93Z2871805

iTrader: (5)

It's been said before, but that is one mean looking T/A! Just to let you know, I was planning on "borrowing" that idea on the air dam, it looks awesome. Do you have any driving issues with it though?

MattSapp95_T/A

iTrader: (35)

Yes we sprayed it in my garage.. We just wet the floors down..since it was just the engine bay we didn't worry about getting a booth....

The air compressor is a Craftsman Belt driven 30 gallon with a water separator on it....The Gun is a Devilbiss HVLP.. as for paint I went with Nason Single Stage urethane...

I think the mounts are in different spots but I can't be too sure...Those pedestals on my K member are from PA racing too...may give them a call and see if it can be made to work...or if you need me to pull some measurements let me know

Thanks bud! Yea I actually made and sold about 10 of them and so far no one that I know of has any issues with them...I personally have not either...Mine is about 1" shorter than the stock one though and I tweaked the angle a little to to help clearance....

scj

iTrader: (89)

Thanks man. I called PA and was told the mounts are different on the kmember. I could send it in with $50 to change the mounts over though. not too bad, i'll prolly just go with a UMI though.

robsquikz28

iTrader: (246)

Matt, car looks good and the engine bay looks like my brothers engine after we painted it. Red cars exterior with black underhood looks badass

MattSapp95_T/A

iTrader: (35)

Wow that isn't bad for the mounts...That is the way i would go.. UMI is heavier...

Thanks! Yea i think the black looks really good! now I just have to make sure all the parts on my motor look up to par...And paint my cowl and other misc plastics...

Hopefully my cam comes soon so I can button up the motor...

Matt

robsquikz28

iTrader: (246)

Matt, did you paint the entire undercarriage black as well?

If so do you have any pics?

MattSapp95_T/A

iTrader: (35)

I went all the way down the Trans tunnel with the gloss black automotive paint and the rest of it is the rubber undercoating that comes in a spray can...

No pics yet but I will get some for you..

Matt

robsquikz28

iTrader: (246)

I will be waiting

MattSapp95_T/A

iTrader: (35)

well I got most of the harness put back in tonight and cleaned up all the extra connectors that I no longer need.... Man I need that cam I am running out of things to do....lol

ThreeHonks

iTrader: (10)

Looks really good! i've been following this thread even thos I havent posted in it yet lol

MattSapp95_T/A

iTrader: (35)

I will have more posted up next week when my cam comes in...shouldn't be too long now until I sit the motor in...