355 LT1 Track Progress
#21
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Damned thing had the wheels up. It doesn't need suspension. It needs a driver.
You can swap tire sizes between nitrous and n/a to get real close on the setup, especially with a stick shift. I'd get some 26s for n/a if i was running your car.
You can swap tire sizes between nitrous and n/a to get real close on the setup, especially with a stick shift. I'd get some 26s for n/a if i was running your car.
#23
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
You realize wheels up doesn't always equal fast correct?
It does need suspension, it is twisting hard in the rear, needs a drag bar and DA shocks at least so it can carry out that initial hit through the 60.
Its getting the cam sync issues squared away so I know that's not affecting the high RPM revs, cage, and suspension. Then reevaluate.
Oh and rim screws or bead locks, it spun the tire about 10 inches
#24
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
You can't come off the clutch any slower. Its an on / off switch at the moment. Maybe I needs better slave cylinder.
You realize wheels up doesn't always equal fast correct?
It does need suspension, it is twisting hard in the rear, needs a drag bar and DA shocks at least so it can carry out that initial hit through the 60.
Its getting the cam sync issues squared away so I know that's not affecting the high RPM revs, cage, and suspension. Then reevaluate.
Oh and rim screws or bead locks, it spun the tire about 10 inches
You realize wheels up doesn't always equal fast correct?
It does need suspension, it is twisting hard in the rear, needs a drag bar and DA shocks at least so it can carry out that initial hit through the 60.
Its getting the cam sync issues squared away so I know that's not affecting the high RPM revs, cage, and suspension. Then reevaluate.
Oh and rim screws or bead locks, it spun the tire about 10 inches
What I saw was a little 355 giving it's all to get the wheels up and then falling on its face. If it keeps its head up (and the tires up), that will gain alot more than a "good" suspension.
For sure, you need to work out the cam synch issues. Make sure your cam sensor is wired with a twisted pair running far away from any ignition secondary parts. Your valvetrain should be happy to 7k and 135 traps. This will affect your n/a runs on shift extension as well.
I was surprised to see you spraying on the first time out. I'd want to take one step at a time and make it run the best on motor first before I head after the best spray numbers. I've never sorted out a combo jumping from place to place in the past. Make one change at a time and see what it does is the path to victory in my experience.
#29
#30
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Sure, there are gains to be made in the suspension. But, it is working pretty decent, not the first thing I would concentrate on to make gains.
What I saw was a little 355 giving it's all to get the wheels up and then falling on its face. If it keeps its head up (and the tires up), that will gain alot more than a "good" suspension.
What I saw was a little 355 giving it's all to get the wheels up and then falling on its face. If it keeps its head up (and the tires up), that will gain alot more than a "good" suspension.
You need a suspension to launch properly...instead of trying to keep the wheels up, he needs to make the car move forward. Its wasting a ton of engery twisting and fighting itself. Getting the proper weight transfer, sway bars, and pinion angle will help a lot.
Still an impressive first time out, the car surely has some potential.
#33
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I didn't say the same time but the bottle gets you alot closer than sucking the wind that is out there. All dialed in, I think it will be within a few tenths on spray, regardless of altitude. On motor, that is a different story, about a second in it there.
#34
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I wouldn't say his suspension is working pretty decent at all - his car has a LOT more in it then a 1.9 60' NA, but he will need suspension tweaking to get there. Getting that down will make huge payoffs on the big end.
You need a suspension to launch properly...instead of trying to keep the wheels up, he needs to make the car move forward. Its wasting a ton of engery twisting and fighting itself. Getting the proper weight transfer, sway bars, and pinion angle will help a lot.
Still an impressive first time out, the car surely has some potential.
You need a suspension to launch properly...instead of trying to keep the wheels up, he needs to make the car move forward. Its wasting a ton of engery twisting and fighting itself. Getting the proper weight transfer, sway bars, and pinion angle will help a lot.
Still an impressive first time out, the car surely has some potential.
#37
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I should have dyno sheets tomorrow to get a better picture of the powerband.
It should not have been hitting the rev limiter at 125-127 mph. I think this was due to some cam sync issues I was having. I rewired the sensor to the PCM tonight and the codes are not present when running, but return when I shut the car off... Go figure.
I did however pull the car WAY past the MPH it was breaking up at the track, and it pulled hard and smooth, so I do believe that fixed the issue of the phantom rev limiter.
It should not have been hitting the rev limiter at 125-127 mph. I think this was due to some cam sync issues I was having. I rewired the sensor to the PCM tonight and the codes are not present when running, but return when I shut the car off... Go figure.
I did however pull the car WAY past the MPH it was breaking up at the track, and it pulled hard and smooth, so I do believe that fixed the issue of the phantom rev limiter.
#39
TECH Fanatic
iTrader: (8)
Join Date: Jan 2011
Location: Pinellas Park Florida
Posts: 1,550
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Do you still have the stock torque arm set up?
If so im betting a torque arm relocation will help a ton, and add a extreme sway bar should really help. Im betting on launch your factory torque arm is bending pretty good.
If so im betting a torque arm relocation will help a ton, and add a extreme sway bar should really help. Im betting on launch your factory torque arm is bending pretty good.
#40
Village Troll ![](http://jameskellock.tripod.com/sitebuildercontent/sitebuilderpictures/rsman.jpg)
![](http://jameskellock.tripod.com/sitebuildercontent/sitebuilderpictures/rsman.jpg)
iTrader: (2)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
At the very least- Adjustable/chassis mount T/A with DS loop, Stiff shocks/springs in back, drag bar, rebound only adjustable shocks up front with stock springs or equivalent.
If you are going to concentrate on launching on spray you need not worry what the car does N/A. I know you said you were going to do this already, but the car needs to be lowered.
If you are going to concentrate on launching on spray you need not worry what the car does N/A. I know you said you were going to do this already, but the car needs to be lowered.