Be afraid....
#61
This is a sick build up for sure.... Question for you, What is the alluminum/sheet metal contraption on the driver side front corner for? Those headers are bad *** to, shed some light on how to get a set of those!
#63
Thread Starter
10 Second Club
iTrader: (8)
Joined: Nov 2001
Posts: 10,023
Likes: 6
From: LT1 land...the "409" of the 90s!
Many People have been asking what is in it. I will try to cover some of it for everyone.
Engine
LTx Block 4.030 Bore with Cats Billet Splyde main caps and ARP Studd's
Eagle 4340 Indexed Crankshaft at .010/.010
Lunati 6in ProMod Rods
coated H bearings on all and coated Cam bearings
Wiseco Dome Pistons(14 To 1)
Hell Fire file fit rings
Thick Piston pins
Comp Cams Belt Drive
Milidon Std Volume Oil pump and custom built pick up
B&B 7Qt Race pan(fixed all oiling issues
ATI Harmonic Damper
Custom Comp Cam(listed earlier in thread)
Comp Cams Elite Solid lifters
Smith Brothers 8.400 length 3/8th by .120 wall push rods
T&D Shaft rockers
2.10 int/1.65 ext valves
Manley NexTek springs (410psi installed and 740psi over the nose)
Lots of titainium to match the NexTek springs
It is all sitting on a set of Brodix -18 High port/Spread port heads
Other goodies bolted to the engine
JakesZ28 Motor plate front and Speed Secrets Plate back
Areospace Vacuum pump
Jegs 140amp Alt
Moroso Mandrel system
FAST Crank trigger
Speed Secrets Cam pickup
Magnafuel 1000 fuel pump driven off the cam shaft
Hogans Custom Intake
Custom Nitro Daves Twin stage Direct port
TPIs Mono blade(for now)
MSD crank trigger Distibutor
Power Master XS starter
I made the headers my self. I spent about $550 in materials
2in stepped to 1 7/8th into a 3.5 merge collectors
Griffen Radiator
Meziere Frame mount Water pump
Custom built Surg Tank(that aluminum contraption thingy)
Feed by a Holley 1400 pump
Those are the basical mechanicals I can think of.
BTW I am on pain meds right now so If I screwed some thing up live with it
Engine
LTx Block 4.030 Bore with Cats Billet Splyde main caps and ARP Studd's
Eagle 4340 Indexed Crankshaft at .010/.010
Lunati 6in ProMod Rods
coated H bearings on all and coated Cam bearings
Wiseco Dome Pistons(14 To 1)
Hell Fire file fit rings
Thick Piston pins
Comp Cams Belt Drive
Milidon Std Volume Oil pump and custom built pick up
B&B 7Qt Race pan(fixed all oiling issues
ATI Harmonic Damper
Custom Comp Cam(listed earlier in thread)
Comp Cams Elite Solid lifters
Smith Brothers 8.400 length 3/8th by .120 wall push rods
T&D Shaft rockers
2.10 int/1.65 ext valves
Manley NexTek springs (410psi installed and 740psi over the nose)
Lots of titainium to match the NexTek springs
It is all sitting on a set of Brodix -18 High port/Spread port heads
Other goodies bolted to the engine
JakesZ28 Motor plate front and Speed Secrets Plate back
Areospace Vacuum pump
Jegs 140amp Alt
Moroso Mandrel system
FAST Crank trigger
Speed Secrets Cam pickup
Magnafuel 1000 fuel pump driven off the cam shaft
Hogans Custom Intake
Custom Nitro Daves Twin stage Direct port
TPIs Mono blade(for now)
MSD crank trigger Distibutor
Power Master XS starter
I made the headers my self. I spent about $550 in materials
2in stepped to 1 7/8th into a 3.5 merge collectors
Griffen Radiator
Meziere Frame mount Water pump
Custom built Surg Tank(that aluminum contraption thingy)
Feed by a Holley 1400 pump
Those are the basical mechanicals I can think of.
BTW I am on pain meds right now so If I screwed some thing up live with it
#65
Thread Starter
10 Second Club
iTrader: (8)
Joined: Nov 2001
Posts: 10,023
Likes: 6
From: LT1 land...the "409" of the 90s!
Yup They are ported. They flowed 340 out of the box and flow more now
I Have been spending money on them for the last ten years. I know there is over $3K in rockers, Valve train and porting alone
I Have been spending money on them for the last ten years. I know there is over $3K in rockers, Valve train and porting alone
#67
Thread Starter
10 Second Club
iTrader: (8)
Joined: Nov 2001
Posts: 10,023
Likes: 6
From: LT1 land...the "409" of the 90s!
Thank for the words Tanner man. I am trying
BTW WHY In the hell can't Accell just put "DK BLUE wire at K2 goes to coil or MSD"????? Instead of me looking for two hours!
BTW WHY In the hell can't Accell just put "DK BLUE wire at K2 goes to coil or MSD"????? Instead of me looking for two hours!
Last edited by TwoFast4Lv; 09-14-2012 at 12:02 AM.
#69
whats your future plans for the TB Ellis? amazing craftsmanship on those headers btw
you can get sbc heads converted for around $400
you can get sbc heads converted for around $400
#71
Max effort-esque project build with a eagle crank... why haven't the naysayers chimed in yet?!
following the build and I am constantly finding myself scratching my head thinking "why didn't I think of that?".
following the build and I am constantly finding myself scratching my head thinking "why didn't I think of that?".
#74
Mike said it will be fine for my goals, you as well as BigCat are running "eagle junk" and seem to be doing fine.
hopefully one day I can get around to checking the list of ideas for the car I have off. Never done an Fbody before and having people like you to guide the build are definitely a plus.
#75
Just gotta make sure someone who knows what they are doing goes over them first, not just take it out of the box and drop it in the block.
#76
#77
Thread Starter
10 Second Club
iTrader: (8)
Joined: Nov 2001
Posts: 10,023
Likes: 6
From: LT1 land...the "409" of the 90s!
I did a little more today. Moving around a littl more while trying to pass my Kidney stones :S
Nose is on for the first time since 2009. Head linght switch is wired and working fine
LOTS of room for Front facing Ram Air intake
Oh baby I think this is going to work out! I got some carbon work to do but I think I am going to like it!
Tomorrow it hits the ground and moves out side so I can clean the shop and move it over a bay
Nose is on for the first time since 2009. Head linght switch is wired and working fine
LOTS of room for Front facing Ram Air intake
Oh baby I think this is going to work out! I got some carbon work to do but I think I am going to like it!
Tomorrow it hits the ground and moves out side so I can clean the shop and move it over a bay
#78
Nice build. While the run-down on the "build" sheet is a nice reference, we all should recognize that God is in the details and a lot of the things that will separate this from most lies in them. Again, stellar build!
#79
Thread Starter
10 Second Club
iTrader: (8)
Joined: Nov 2001
Posts: 10,023
Likes: 6
From: LT1 land...the "409" of the 90s!
Thank you for the words. You are 100% correct. It is hard to explain the hundreds of hours in all of the details that is for sure.
I have it outside today so I can clean the shop. I forgot how insaine it looks in the sun!
Had to roll it out on the jack. the front Susention is no where near set yet. It should come down 2in or so when it is done
I have it outside today so I can clean the shop. I forgot how insaine it looks in the sun!
Had to roll it out on the jack. the front Susention is no where near set yet. It should come down 2in or so when it is done