car wont stay running after valve adjustment
#1
11 Second Club
Thread Starter
iTrader: (46)
Join Date: Feb 2004
Location: jacksonville, fl
Posts: 1,667
Likes: 0
Received 0 Likes
on
0 Posts
car wont stay running after valve adjustment
well i bent a pushrod last week and got the new ones in today. they are summit brand chromemoly stock length. the car has the lt4 hotcam kit with ported heads/intake, headers, cai and delteq. after adjusting the valves... getting each cylinder one at a time on roll over and spinning the pushrod until it stops spinning while tightning down the nut. then giving it a half a turn then locking it in place. i did that on all the cylinders and then when i hooked everything back up the car would fire and run for a second, but then it just dies. if i give it gas it will stay running for a brief second then die again. there is no chattering like the rockers are loose or anything... and i dont think the valves are too tight so i just dont know what it could be. all sensors are hooked up and the ses light is not on. so any and all help is greatly appreciated. thanks alot
daniel
daniel
#2
TECH Enthusiast
iTrader: (6)
Join Date: Nov 2005
Location: Michigan
Posts: 744
Likes: 0
Received 0 Likes
on
0 Posts
when you tried to start it, did you have the maf on the TB?
The car will do exactly what your talking about if the MAF isn't on. it'll start for a second, even if you have the gas down to the floor it won't rev, itlll just die.
The car will do exactly what your talking about if the MAF isn't on. it'll start for a second, even if you have the gas down to the floor it won't rev, itlll just die.
#6
TECH Addict
iTrader: (8)
Join Date: Sep 2005
Location: The beautiful Kingdom of Bahrain
Posts: 2,401
Likes: 0
Received 0 Likes
on
0 Posts
I just noticed he never mentioned the year of his setup. If it's a 93 then this whole maf convo is pointless. Ive run my car at idle just fine without the maf connected. Also I wouldnt rule out something in the ignition causing this. Id just double and triple check all my work and make sure EVERYTHING is plugged back up.
Trending Topics
#9
11 Second Club
Thread Starter
iTrader: (46)
Join Date: Feb 2004
Location: jacksonville, fl
Posts: 1,667
Likes: 0
Received 0 Likes
on
0 Posts
wow... look at all the responses! damn this lt1 forum is so much better than the ls1 lol. it took forever to get help over there when i had one haha.
but blackbird pretty much hit it on the head... the intake elbow is such a pain in the *** to get on that i just left it off to try and start the car. so i put it back on and sho nuff it works great.
only problem now is that she has a high rpm miss, what all could cause that?
but blackbird pretty much hit it on the head... the intake elbow is such a pain in the *** to get on that i just left it off to try and start the car. so i put it back on and sho nuff it works great.
only problem now is that she has a high rpm miss, what all could cause that?
#12
TECH Resident
iTrader: (10)
Join Date: Sep 2003
Location: Fernandina Beach, Florida
Posts: 755
Likes: 0
Received 0 Likes
on
0 Posts
if you need any help... you can email me i live only about 30 min away from you.. so if your ever stumped email me at harvickgm@yahoo.com
#15
11 Second Club
Thread Starter
iTrader: (46)
Join Date: Feb 2004
Location: jacksonville, fl
Posts: 1,667
Likes: 0
Received 0 Likes
on
0 Posts
sweet. that eliminates one more thing lol.
now i read somewhere that over tightened valves could cause this type of stumble. and after further "testing" lol i found out that it starts to miss at about 4000 rpms and on up. what do yall think of that?
now i read somewhere that over tightened valves could cause this type of stumble. and after further "testing" lol i found out that it starts to miss at about 4000 rpms and on up. what do yall think of that?
#16
11 Second Club
Thread Starter
iTrader: (46)
Join Date: Feb 2004
Location: jacksonville, fl
Posts: 1,667
Likes: 0
Received 0 Likes
on
0 Posts
but i was wondering, could it be because the stock knock module is picking up extra noise? it didnt have this problem before i did the valves, so pretty much that is what is left. if i adjust the valves and it doesnt go away? i made sure nothing was arching and all the plugs are snug and have good connections.
btw, it starts to miss at about 4000 rpm or so. plugs are autolite 106's gapped to .050
btw, it starts to miss at about 4000 rpm or so. plugs are autolite 106's gapped to .050
#17
11 Second Club
iTrader: (1)
Originally Posted by 68birdls1
well i bent a pushrod last week and got the new ones in today. they are summit brand chromemoly stock length. the car has the lt4 hotcam kit with ported heads/intake, headers, cai and delteq. after adjusting the valves... getting each cylinder one at a time on roll over and spinning the pushrod until it stops spinning while tightning down the nut. then giving it a half a turn then locking it in place. i did that on all the cylinders and then when i hooked everything back up the car would fire and run for a second, but then it just dies. if i give it gas it will stay running for a brief second then die again. there is no chattering like the rockers are loose or anything... and i dont think the valves are too tight so i just dont know what it could be. all sensors are hooked up and the ses light is not on. so any and all help is greatly appreciated. thanks alot
daniel
daniel