Ford 9" Rear
Ford 9" Rear I know there is a couple of guys in here..I am looking at one of these from Moser to go into my 95 Z, I have seen a few people with this, and it is pretty reasonably priced. What all did you guys get to make it work? I plan on getting the Housing and Axles, and getting a Ford 9" Auburn Pro Series Posi Differential, and then 3.73's. Summit sells Gears for Ford, but it says for 8.8", are these the same? Also, what Pinion Yoke do I need if I go with this setup. If I need to know anything else, throw it in.
Thanks.
Thanks.
I am not really worried about it, I already have the front ABS gone. Has anyone got a way to delete the ABS Module and put a little splitter in there, or is it just less work to keep it in there and functioning.
not sure how much you are looking to spend but I got mine from Scott@driveline-solutions. hes a vendor on the board. he sells a budget 9" with the center section assembled and everything else loose. 31 spline axles, 4.11s, and true-trac posi for just under 2000 shipped. With the upgraded driveshaft and yokes I believe it was around 2400. Awesome guy to deal with as well.
Trending Topics
I have a Moser 9" under my car and here's what i ordered. it's been under the car for about 8 years and I've NEVER had a problem with it..... You have to order gears for a 9" and not for an 8.8" rear.... Two different rears. Moser should be able to hook you up with the whole package like they did for me. They'll send you everything.
I got the Moser 9" with backbrace, stock length axle tubes for 4th gen f-body, all suspension brackets for 4th gen f-body, nodular iron case, Richmond 3.89 gears, billet pinion support, 35 spline axles, detroit locker and a 1350 spicer yoke for the front..... I got timken axle bearings also. supposedly the best... They should send it with all the bearings and seals you need as well...
Think mine came to like 2200-2300 shipped...
I got the Moser 9" with backbrace, stock length axle tubes for 4th gen f-body, all suspension brackets for 4th gen f-body, nodular iron case, Richmond 3.89 gears, billet pinion support, 35 spline axles, detroit locker and a 1350 spicer yoke for the front..... I got timken axle bearings also. supposedly the best... They should send it with all the bearings and seals you need as well...
Think mine came to like 2200-2300 shipped...
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo I plan on just getting the Ford 9" Housing and Axles to fit my Camaro, and then I got a Posi from a different place to drop in, as well as the Gears. I got it all priced at about $1800.
Launching!
Joined: May 2006
Posts: 250
Likes: 0
From: Sugar Hill, GA
I got the moser housing and 31 spline axle setup assy and ordered the center section from a company on ebay that thats all they build is 9" center sections it's 1350 yoke nodular case with 4.33 gears and a posi. has held up to hard launches with front wheels up.
