E-Cutout Switch Location
E-Cutout Switch Location Where have ya'll mounted your Electric Cutout Switches, Need it somewhere easily reachable without being in the way. Doesn't have to be this switch, but need a nice looking location.
Also, a beer bottle coozie works good as a faceplate holder if you've lost the case. Just a thought.
-Rick
Also, a beer bottle coozie works good as a faceplate holder if you've lost the case. Just a thought.
-Rick
Trending Topics
You can buy a cutout on basically any online parts store. WS6Store has 'em. If you don't mind reaching under the car and undoing 3 wingnuts, you can save yourself a decent amount of money by not getting an electric one. Not quite as convenient though.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
I think i'm going to put my under the cig lighter. because I want to put the N20 controls in the ash tray.
i'v always thought about making a plate to cover the cubby hole area, and putting 4 switches across from each other on it too. I think it would look
i'v always thought about making a plate to cover the cubby hole area, and putting 4 switches across from each other on it too. I think it would look
Yeah, I really thought about deleting my cig lighter and putting the little switch there if the hole was the right size. I really want to relocate my cig lighter anyways, I want to move it and add one more, I use mine as a power port anyways. So now I gotta find a spot to locate two power ports (cig lighters).
-Rick
-Rick
The only thing I noticed about putting it in the ash tray or around the cig lighter is that I'd have to reach around my shifter to get to it. I have a T-handle shifter so that little area is kinda hard to reach. I kinda thought about putting it on the side of the cup holder, facing the inside on the flat wall by the ebrake. My thumb kinda naturally lays there and there is plenty of room on the inside by the ebrake to run wires and for the switch. It would be out of the way and if I ever put a cup in there it shouldn't come close to touching it.
-rick
-rick
The only thing I noticed about putting it in the ash tray or around the cig lighter is that I'd have to reach around my shifter to get to it. I have a T-handle shifter so that little area is kinda hard to reach. I kinda thought about putting it on the side of the cup holder, facing the inside on the flat wall by the ebrake. My thumb kinda naturally lays there and there is plenty of room on the inside by the ebrake to run wires and for the switch. It would be out of the way and if I ever put a cup in there it shouldn't come close to touching it.
-rick
-rick
Yeah, I'm gonna go with the electric ones...3'' after the Y pipe...
try removing the rear defrost switch and putting it there? or taping the rear defrost sw? I want to say I heard of a guy that used the rear defrost to arm/disarm the line lock on his 2000 Camaro, so when you looked in the car you never saw anaything that the factory did not place there,
^ I don't have rear defrost, but I do have a new hatch with it though, may install it before next winter...
I already installed my switch, I put it right under the cig lighter. Looks fairly good there, and ofcouse I broke the little clip off the damn panel when I was taking it out.
-Rick
I already installed my switch, I put it right under the cig lighter. Looks fairly good there, and ofcouse I broke the little clip off the damn panel when I was taking it out.
-Rick
