LS1TECH - Camaro and Firebird Forum Discussion

Manual Transmission T56 | T5 | MN12 | Clutches | Hydraulics | Shifters

Aftermarket T56 gears

Thread Tools
 
Search this Thread
 
Old 03-17-2016, 06:37 PM
  #21  
TECH Apprentice
 
AMP-D's Avatar
 
Join Date: Sep 2014
Location: Merica
Posts: 354
Received 22 Likes on 16 Posts
Default
Originally Posted by 370ci_NBM_SS
Viper shafts need longer splines for the slip yoke too
Our Viper shaft will have longer splines to allow for machining to fit conversion units. There are a few other helpful modifications we've yet to release until a working sample is available for testing.
AMP-D is offline  
Reply Like
Old 03-18-2016, 07:53 AM
  #22  
Staging Lane
 
370ci_NBM_SS's Avatar
 
Join Date: Mar 2011
Location: Warshington
Posts: 83
Likes: 0
Received 0 Likes on 0 Posts

Default
Originally Posted by AMP-D
Our Viper shaft will have longer splines to allow for machining to fit conversion units. There are a few other helpful modifications we've yet to release until a working sample is available for testing.
A 32 spline triple cone and non triple cone main shaft would be sweet as well.
370ci_NBM_SS is offline  
Reply Like
Old 03-18-2016, 08:32 AM
  #23  
TECH Apprentice
 
AMP-D's Avatar
 
Join Date: Sep 2014
Location: Merica
Posts: 354
Received 22 Likes on 16 Posts
Default
Originally Posted by 370ci_NBM_SS
A 32 spline triple cone and non triple cone main shaft would be sweet as well.
We're working on that as well but its a little further down the road.
AMP-D is offline  
Reply Like
Old 03-18-2016, 01:42 PM
  #24  
Staging Lane
 
370ci_NBM_SS's Avatar
 
Join Date: Mar 2011
Location: Warshington
Posts: 83
Likes: 0
Received 0 Likes on 0 Posts

Default
Originally Posted by AMP-D
We're working on that as well but its a little further down the road.
Very nice shouldn't be hard to sell
370ci_NBM_SS is offline  
Reply Like
Old 03-18-2016, 06:38 PM
  #25  
TECH Junkie
iTrader: (100)
 
ROCNDAV's Avatar
 
Join Date: Mar 2004
Location: Pasadena, CA
Posts: 3,725
Received 1 Like on 1 Post

Default
Originally Posted by AMP-D
We're working on that as well but its a little further down the road.
That would be cool!

Now to get GM to stock SSR tailshaft housings again.
ROCNDAV is offline  
Reply Like
Old 03-18-2016, 10:21 PM
  #26  
TECH Apprentice
 
AMP-D's Avatar
 
Join Date: Sep 2014
Location: Merica
Posts: 354
Received 22 Likes on 16 Posts
Default
Originally Posted by ROCNDAV
That would be cool!

Now to get GM to stock SSR tailshaft housings again.
We looked at die casting some stuff but that gets real expensive and the only way to average out the cost is to do a ton of the stuff. We're talking 10,000 pieces or so to get the pricing down to justify the cost.
AMP-D is offline  
Reply Like
Old 03-19-2016, 05:43 PM
  #27  
TECH Junkie
iTrader: (100)
 
ROCNDAV's Avatar
 
Join Date: Mar 2004
Location: Pasadena, CA
Posts: 3,725
Received 1 Like on 1 Post

Default
Do you make Corvette input shafts with MM6 (2.66) 1st gear ratios?

GM PN 89060070
Last edited by ROCNDAV; 03-19-2016 at 07:14 PM.
ROCNDAV is offline  
Reply Like
Old 03-19-2016, 07:48 PM
  #28  
TECH Apprentice
 
AMP-D's Avatar
 
Join Date: Sep 2014
Location: Merica
Posts: 354
Received 22 Likes on 16 Posts
Default
Originally Posted by ROCNDAV
Do you make Corvette input shafts with MM6 (2.66) 1st gear ratios?

GM PN 89060070
We are working on it. We should have a working sample to test by the end of the summer. It will be based on our Viper spec LS input shaft that is currently available. Hopefully we'll have a 29 tooth 2.97 shaft later this year for testing as well.
AMP-D is offline  
Reply Like
Old 03-25-2016, 04:43 PM
  #29  
TECH Apprentice
 
AMP-D's Avatar
 
Join Date: Sep 2014
Location: Merica
Posts: 354
Received 22 Likes on 16 Posts
Default
We just got our Viper spec LT1 T56 input shafts in stock if any LT guys are in need.
AMP-D is offline  
Reply Like
Old 05-04-2016, 07:59 AM
  #30  
TECH Apprentice
 
AMP-D's Avatar
 
Join Date: Sep 2014
Location: Merica
Posts: 354
Received 22 Likes on 16 Posts
Default
Some Corvette T56 gears we are currently testing with a few undisclosed builders we supply parts to.
Attached Thumbnails Aftermarket T56 gears-img_6854.jpg   Aftermarket T56 gears-img_6853.jpg  
AMP-D is offline  
Reply Like
Old 05-04-2016, 08:59 AM
  #31  
TECH Junkie
iTrader: (100)
 
ROCNDAV's Avatar
 
Join Date: Mar 2004
Location: Pasadena, CA
Posts: 3,725
Received 1 Like on 1 Post

Default
Good news
ROCNDAV is offline  
Reply Like
Old 05-04-2016, 12:28 PM
  #32  
TECH Junkie
iTrader: (100)
 
ROCNDAV's Avatar
 
Join Date: Mar 2004
Location: Pasadena, CA
Posts: 3,725
Received 1 Like on 1 Post

Default
Now if you could only start making these:

https://ls1tech.com/forums/manual-tr...-question.html

ROCNDAV is offline  
Reply Like
Old 05-04-2016, 09:11 PM
  #33  
TECH Apprentice
 
AMP-D's Avatar
 
Join Date: Sep 2014
Location: Merica
Posts: 354
Received 22 Likes on 16 Posts
Default
Originally Posted by ROCNDAV
Now if you could only start making these:

https://ls1tech.com/forums/manual-tr...-question.html

We have some but we didn't make them.
AMP-D is offline  
Reply Like
Old 05-05-2016, 01:04 AM
  #34  
TECH Junkie
iTrader: (100)
 
ROCNDAV's Avatar
 
Join Date: Mar 2004
Location: Pasadena, CA
Posts: 3,725
Received 1 Like on 1 Post

Default
For sale?
ROCNDAV is offline  
Reply Like
Old 05-05-2016, 08:25 AM
  #35  
TECH Apprentice
 
AMP-D's Avatar
 
Join Date: Sep 2014
Location: Merica
Posts: 354
Received 22 Likes on 16 Posts
Default
Originally Posted by ROCNDAV
For sale?
Yes
AMP-D is offline  
Reply Like
Old 05-10-2016, 07:29 AM
  #36  
Teching In
 
lsx55's Avatar
 
Join Date: May 2016
Location: NC USA
Posts: 43
Likes: 0
Received 0 Likes on 0 Posts
Default
Avoid anything without warranty!
lsx55 is offline  
Reply Like
Old 05-10-2016, 10:29 PM
  #37  
TECH Apprentice
 
AMP-D's Avatar
 
Join Date: Sep 2014
Location: Merica
Posts: 354
Received 22 Likes on 16 Posts
Default
Originally Posted by lsx55
Avoid anything without warranty!
Do you think Tremec offers a warranty on their gears? If so, think again, especially if you rip the teeth off one and try to get another one for free.
AMP-D is offline  
Reply Like
Old 05-17-2016, 11:00 PM
  #38  
Staging Lane
 
370ci_NBM_SS's Avatar
 
Join Date: Mar 2011
Location: Warshington
Posts: 83
Likes: 0
Received 0 Likes on 0 Posts

Default
I ordered some parts, was wondering if there is a way to track it. The only thing "my account" says is order received.Thanks
370ci_NBM_SS is offline  
Reply Like
Old 05-22-2016, 06:04 PM
  #39  
On The Tree
 
98znasty's Avatar
 
Join Date: Sep 2015
Location: Tucson AZ
Posts: 153
Likes: 0
Received 0 Likes on 0 Posts
Default
I got an aftermarket input shaft from Hawks and it worked but was very noisy ended up having my old one fixed and put it back in. I will not run any aftermarket hard parts in this t56 ever again
98znasty is offline  
Reply Like
Old 05-22-2016, 09:23 PM
  #40  
TECH Apprentice
 
AMP-D's Avatar
 
Join Date: Sep 2014
Location: Merica
Posts: 354
Received 22 Likes on 16 Posts
Default
Originally Posted by 98znasty
I got an aftermarket input shaft from Hawks and it worked but was very noisy ended up having my old one fixed and put it back in. I will not run any aftermarket hard parts in this t56 ever again
Sorry to hear that. I believe they sell the Korean made input shaft and we've heard a lot of complaints about it making noise.
AMP-D is offline  
Reply Like



Advanced Search
Quick Reply: Aftermarket T56 gears


Reply Closed Thread Share

All times are GMT -5. The time now is 08:43 PM.