Updated: THREE trips to TNT with pics + vids
#342
10 Second Club
iTrader: (41)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Well sort of changed directions......REALLY changed directions. Long story short I just hadn't 100% bought into the nitrous idea, for several reasons. I made a comment to a buddy what if i sold everything i have and started over. He mentioned that to his boss who has a GTO that needs a drivetrain and 2 weeks later I have a roller. I sold the complete motor, intake, converter, and trans.
As of right now I have purchased (with the above money), an 05 Gen3 5.3 (gen4 rods) complete engine, Isky turbo cam, head studs, LS9 gaskets, Melling pump, LS2 timing set, LS7 lifters, dual springs, -10AN catch can, Huron speed turbo kit with their billet 78/75 turbo, bumper exit trim ring, Bosch 127lb injectors, billet fuel rails, and Im basically out of money. So I'm gonna start the build, save some dough for my fuel system, new trans and converter. Goal is 15 to 20 psi on e85. Complete teardown and pics of parts coming soon. Stay tuned.
As of right now I have purchased (with the above money), an 05 Gen3 5.3 (gen4 rods) complete engine, Isky turbo cam, head studs, LS9 gaskets, Melling pump, LS2 timing set, LS7 lifters, dual springs, -10AN catch can, Huron speed turbo kit with their billet 78/75 turbo, bumper exit trim ring, Bosch 127lb injectors, billet fuel rails, and Im basically out of money. So I'm gonna start the build, save some dough for my fuel system, new trans and converter. Goal is 15 to 20 psi on e85. Complete teardown and pics of parts coming soon. Stay tuned.
Btw you will love your Huron speed kit! You should have a lighter car then I do with similar power. I bet you will be in the 9's in no time...
#343
TECH Senior Member
Thread Starter
iTrader: (96)
Join Date: Aug 2007
Location: Turnin' Wrenches Infractions: 005
Posts: 24,240
Likes: 0
Received 81 Likes
on
72 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Got lots of pics to update, may do that tomorrow. All main components are purchased. I have a 4l80e in my possession and the motor is almost done. I will let the pics do the talking when I upload and explain my trans and converter choice etc etc. I'm guessing my weight will be 3100 all said and done, which is not bad for an iron block turbo car. So that part will still be helping me.
#345
TECH Senior Member
Thread Starter
iTrader: (96)
Join Date: Aug 2007
Location: Turnin' Wrenches Infractions: 005
Posts: 24,240
Likes: 0
Received 81 Likes
on
72 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Lots of parts have been ordered, and lots have been showing up.....and I still think of new things daily. I started with the tear-down and inspection of the 2005 5.3. Bearings were acceptable, and cylinders looked really nice. I spent hours at this point to make it look this nice.
![Name: 20170625_161717_zps1tj8c91k.jpeg
Views: 4456
Size: 234.1 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583523d1501199626-updated-three-trips-tnt-pics-vids-20170625_161717_zps1tj8c91k.jpeg)
Here is the Isky cam, grind 271-HR-672. Specs are something like 218/218 .570 .570 112. Its my understanding it was spec'd for a turbo setup. The way I ended up with it is a buddy locally had it for sale, it was brand new, and it was quite a bit cheaper then new, so here it is.
![Name: 20170628_143213_zps3cnugv3h.jpeg
Views: 4414
Size: 115.4 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583524d1501199626-updated-three-trips-tnt-pics-vids-20170628_143213_zps3cnugv3h.jpeg)
New timing set, and I wanted to drill the block for the damper but it looked like the holes would go through and hit the crank so I said **** it and through it in the scrap parts pile.
![Name: 20170628_142702_zpsyl5kqiww.jpeg
Views: 4428
Size: 1.03 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583525d1501199626-updated-three-trips-tnt-pics-vids-20170628_142702_zpsyl5kqiww.jpeg)
Knock sensors were crusty so I ordered a set of them, old coolant sensor broke (they are very brittle with age) so there's that in the center, and to the right is a -10 bulkhead fitting. I'm gonna try and get this in the side of the oil pan for my turbo oil drain line.
![Name: 20170629_165656_zps4hguxuvf.jpeg
Views: 4413
Size: 112.0 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583526d1501199626-updated-three-trips-tnt-pics-vids-20170629_165656_zps4hguxuvf.jpeg)
Melling 10295
![Name: 20170628_145242_zpsyjd7syba.jpeg
Views: 4475
Size: 767.9 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583527d1501199626-updated-three-trips-tnt-pics-vids-20170628_145242_zpsyjd7syba.jpeg)
Bosch 127s. These were actually an ebay score, dyno runtime only, $600 shipped!!
![Name: 20170622_194941_zpsqzci3rhu.jpeg
Views: 4512
Size: 921.9 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583528d1501199626-updated-three-trips-tnt-pics-vids-20170622_194941_zpsqzci3rhu.jpeg)
New rear cover gasket, rear main seal, water pump gaskets, and new front cam plate.
![Name: 20170628_140109_zps8vejtmfi.jpeg
Views: 4554
Size: 1.13 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583529d1501199626-updated-three-trips-tnt-pics-vids-20170628_140109_zps8vejtmfi.jpeg)
New intake gaskets, NGK BR7s, MSD plug wires fit for truck coils, and a new pinion seal for my 12 bolt, figuring I'm gonna swap out the 4.10s in favor of the 3.73s I have on my shelf.......
![Name: 20170629_165632_zpsdgvuu9rp.jpeg
Views: 4518
Size: 1.05 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583530d1501199626-updated-three-trips-tnt-pics-vids-20170629_165632_zpsdgvuu9rp.jpeg)
Chinese blow off valve, and really nice turbo smart wastegate that came with the huron speed kit (which is backordered BTW). Thats my ebay catch can with -10 lines that will come off each valve cover.
![Name: 20170630_180317_zpsx77fwfto.jpeg
Views: 4508
Size: 1.08 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583531d1501199626-updated-three-trips-tnt-pics-vids-20170630_180317_zpsx77fwfto.jpeg)
Billet fuel rails for the truck intake. Gonna have to figure out if it will work with these LS1 length injectors......Will mock it up soon.
![Name: 20170629_165842_zps8unhbre8.jpeg
Views: 4500
Size: 793.5 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583532d1501199626-updated-three-trips-tnt-pics-vids-20170629_165842_zps8unhbre8.jpeg)
So I took the heads to the machine shop, I told them just get them clean, and touch them with the mill to make sure they seal. No valve work or anything like that. Here they are fresh and clean.
![Name: 20170629_175155_zpsqsc9hoea.jpeg
Views: 4459
Size: 354.9 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583533d1501199626-updated-three-trips-tnt-pics-vids-20170629_175155_zpsqsc9hoea.jpeg)
I basically added some valve grinding compound to the valves, spun them on the seats to make sure everything had a fresh sealing surface, then installed the new dual valve spring kit.
![Name: 20170629_201001_zpsjvq5rd5q.jpeg
Views: 4497
Size: 779.1 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583534d1501199626-updated-three-trips-tnt-pics-vids-20170629_201001_zpsjvq5rd5q.jpeg)
Of course i went with the head studs, and LS9 gaskets, and sealed them down to the engine. I threw the oil pan and front cover on quickly just for paint, they will need to come back off for new gaskets. Added the intake just for the pic. This was left over graphite paint that I used on the Fast 102 intake.
![Name: 20170630_164623_zpsfnrrfjfx.jpeg
Views: 4370
Size: 133.5 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583535d1501199626-updated-three-trips-tnt-pics-vids-20170630_164623_zpsfnrrfjfx.jpeg)
I've got a buddy that goes to the junkyards often so i told him i needed another 4l80e. He ended up driving an hour and a half away to get me the most crusty, dirty, filthy POS trans I've ever seen. But when I opened it up i was pleasantly surprised. The junkyard sells these for $89.
![Name: 20170629_104737_zpsrqdlikxy.jpeg
Views: 4495
Size: 391.0 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583536d1501199626-updated-three-trips-tnt-pics-vids-20170629_104737_zpsrqdlikxy.jpeg)
After careful calculations of time and budget, Ive decided to service this trans and add an HD2 kit and run it as is, and see what it can take.
![Name: 20170630_125006_zpsk78rznte.jpeg
Views: 4467
Size: 1.02 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583537d1501199626-updated-three-trips-tnt-pics-vids-20170630_125006_zpsk78rznte.jpeg)
Once fully involved in the HD2 shift kit install, it was me and my trans buddy's opinion this trans had already been rebuilt. Score!!!!!! That would explain why it was so clean inside.
![Name: 20170630_124954_zps1bvkjy3p.jpeg
Views: 4499
Size: 367.6 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583538d1501199626-updated-three-trips-tnt-pics-vids-20170630_124954_zps1bvkjy3p.jpeg)
With that stroke of good news I called up Circle D converters and got me a shiny new triple disc converter on the way!!! We decided on something loose (due to not having a transbrake at the moment), should footbrake to mid 3K RPMs, and will be a little loose on the big end so I will be anticipating locking it up in 3rd gear. Also, Chrs1313 dual 450 pumps will be here soon, and I just ordered a PST forged 4l80e yoke for my existing driveshaft from Midwest Chassis. Turbo should be here today though the piping is back-ordered. More pictures coming soon, parts are rolling in daily.
![Name: 20170625_161717_zps1tj8c91k.jpeg
Views: 4456
Size: 234.1 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583523d1501199626-updated-three-trips-tnt-pics-vids-20170625_161717_zps1tj8c91k.jpeg)
Here is the Isky cam, grind 271-HR-672. Specs are something like 218/218 .570 .570 112. Its my understanding it was spec'd for a turbo setup. The way I ended up with it is a buddy locally had it for sale, it was brand new, and it was quite a bit cheaper then new, so here it is.
![Name: 20170628_143213_zps3cnugv3h.jpeg
Views: 4414
Size: 115.4 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583524d1501199626-updated-three-trips-tnt-pics-vids-20170628_143213_zps3cnugv3h.jpeg)
New timing set, and I wanted to drill the block for the damper but it looked like the holes would go through and hit the crank so I said **** it and through it in the scrap parts pile.
![Name: 20170628_142702_zpsyl5kqiww.jpeg
Views: 4428
Size: 1.03 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583525d1501199626-updated-three-trips-tnt-pics-vids-20170628_142702_zpsyl5kqiww.jpeg)
Knock sensors were crusty so I ordered a set of them, old coolant sensor broke (they are very brittle with age) so there's that in the center, and to the right is a -10 bulkhead fitting. I'm gonna try and get this in the side of the oil pan for my turbo oil drain line.
![Name: 20170629_165656_zps4hguxuvf.jpeg
Views: 4413
Size: 112.0 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583526d1501199626-updated-three-trips-tnt-pics-vids-20170629_165656_zps4hguxuvf.jpeg)
Melling 10295
![Name: 20170628_145242_zpsyjd7syba.jpeg
Views: 4475
Size: 767.9 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583527d1501199626-updated-three-trips-tnt-pics-vids-20170628_145242_zpsyjd7syba.jpeg)
Bosch 127s. These were actually an ebay score, dyno runtime only, $600 shipped!!
![Name: 20170622_194941_zpsqzci3rhu.jpeg
Views: 4512
Size: 921.9 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583528d1501199626-updated-three-trips-tnt-pics-vids-20170622_194941_zpsqzci3rhu.jpeg)
New rear cover gasket, rear main seal, water pump gaskets, and new front cam plate.
![Name: 20170628_140109_zps8vejtmfi.jpeg
Views: 4554
Size: 1.13 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583529d1501199626-updated-three-trips-tnt-pics-vids-20170628_140109_zps8vejtmfi.jpeg)
New intake gaskets, NGK BR7s, MSD plug wires fit for truck coils, and a new pinion seal for my 12 bolt, figuring I'm gonna swap out the 4.10s in favor of the 3.73s I have on my shelf.......
![Name: 20170629_165632_zpsdgvuu9rp.jpeg
Views: 4518
Size: 1.05 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583530d1501199626-updated-three-trips-tnt-pics-vids-20170629_165632_zpsdgvuu9rp.jpeg)
Chinese blow off valve, and really nice turbo smart wastegate that came with the huron speed kit (which is backordered BTW). Thats my ebay catch can with -10 lines that will come off each valve cover.
![Name: 20170630_180317_zpsx77fwfto.jpeg
Views: 4508
Size: 1.08 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583531d1501199626-updated-three-trips-tnt-pics-vids-20170630_180317_zpsx77fwfto.jpeg)
Billet fuel rails for the truck intake. Gonna have to figure out if it will work with these LS1 length injectors......Will mock it up soon.
![Name: 20170629_165842_zps8unhbre8.jpeg
Views: 4500
Size: 793.5 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583532d1501199626-updated-three-trips-tnt-pics-vids-20170629_165842_zps8unhbre8.jpeg)
So I took the heads to the machine shop, I told them just get them clean, and touch them with the mill to make sure they seal. No valve work or anything like that. Here they are fresh and clean.
![Name: 20170629_175155_zpsqsc9hoea.jpeg
Views: 4459
Size: 354.9 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583533d1501199626-updated-three-trips-tnt-pics-vids-20170629_175155_zpsqsc9hoea.jpeg)
I basically added some valve grinding compound to the valves, spun them on the seats to make sure everything had a fresh sealing surface, then installed the new dual valve spring kit.
![Name: 20170629_201001_zpsjvq5rd5q.jpeg
Views: 4497
Size: 779.1 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583534d1501199626-updated-three-trips-tnt-pics-vids-20170629_201001_zpsjvq5rd5q.jpeg)
Of course i went with the head studs, and LS9 gaskets, and sealed them down to the engine. I threw the oil pan and front cover on quickly just for paint, they will need to come back off for new gaskets. Added the intake just for the pic. This was left over graphite paint that I used on the Fast 102 intake.
![Name: 20170630_164623_zpsfnrrfjfx.jpeg
Views: 4370
Size: 133.5 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583535d1501199626-updated-three-trips-tnt-pics-vids-20170630_164623_zpsfnrrfjfx.jpeg)
I've got a buddy that goes to the junkyards often so i told him i needed another 4l80e. He ended up driving an hour and a half away to get me the most crusty, dirty, filthy POS trans I've ever seen. But when I opened it up i was pleasantly surprised. The junkyard sells these for $89.
![Name: 20170629_104737_zpsrqdlikxy.jpeg
Views: 4495
Size: 391.0 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583536d1501199626-updated-three-trips-tnt-pics-vids-20170629_104737_zpsrqdlikxy.jpeg)
After careful calculations of time and budget, Ive decided to service this trans and add an HD2 kit and run it as is, and see what it can take.
![Name: 20170630_125006_zpsk78rznte.jpeg
Views: 4467
Size: 1.02 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583537d1501199626-updated-three-trips-tnt-pics-vids-20170630_125006_zpsk78rznte.jpeg)
Once fully involved in the HD2 shift kit install, it was me and my trans buddy's opinion this trans had already been rebuilt. Score!!!!!! That would explain why it was so clean inside.
![Name: 20170630_124954_zps1bvkjy3p.jpeg
Views: 4499
Size: 367.6 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583538d1501199626-updated-three-trips-tnt-pics-vids-20170630_124954_zps1bvkjy3p.jpeg)
With that stroke of good news I called up Circle D converters and got me a shiny new triple disc converter on the way!!! We decided on something loose (due to not having a transbrake at the moment), should footbrake to mid 3K RPMs, and will be a little loose on the big end so I will be anticipating locking it up in 3rd gear. Also, Chrs1313 dual 450 pumps will be here soon, and I just ordered a PST forged 4l80e yoke for my existing driveshaft from Midwest Chassis. Turbo should be here today though the piping is back-ordered. More pictures coming soon, parts are rolling in daily.
#348
TECH Senior Member
Thread Starter
iTrader: (96)
Join Date: Aug 2007
Location: Turnin' Wrenches Infractions: 005
Posts: 24,240
Likes: 0
Received 81 Likes
on
72 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Thanks ![Burnout](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_burnout.gif)
Got a few things done on my days off. First, i knew a had a mismatch on injectors/rails. What I have is car injectors, a truck intake, and truck billet rails. Here's the height difference.
![Name: 20170703_131123_zpsszkrkk1s.jpeg
Views: 4520
Size: 1,015.0 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583417d1501199149-updated-three-trips-tnt-pics-vids-20170703_131123_zpsszkrkk1s.jpeg)
After mocking it up and seeing the space between the rail and the intake, I measured that i needed 4 .850 spacers. I went to Home Depot and got some 1/2" square and round tubing. After playing with them I decided I like the square tubing better, so I made 4 spacers and bought 4 longer bolts. I believe they were m6x1.0x40mm.
![Name: 20170703_133952_zpsnrjmcoa1.jpeg
Views: 4437
Size: 141.3 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583418d1501199149-updated-three-trips-tnt-pics-vids-20170703_133952_zpsnrjmcoa1.jpeg)
Both sides on, crossover installed, they fit nice.
![Name: 20170703_140550_zpsprrumab7.jpeg
Views: 4491
Size: 1.13 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583419d1501199149-updated-three-trips-tnt-pics-vids-20170703_140550_zpsprrumab7.jpeg)
Spin the motor over. I'm not gonna use or need the low oil sensor thats in the pan, so I'm gonna remove it and buy a plug. Cruising around ebay searching that size I realize someone makes a plug specifically for this, so I bought it. This is not tapered thread so an oring must be used.
![Name: 20170703_153303_zpsc486e1qa.jpeg
Views: 4456
Size: 846.6 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583420d1501199149-updated-three-trips-tnt-pics-vids-20170703_153303_zpsc486e1qa.jpeg)
Didnt get a complete "before" pic, but i decided to move the oil sump to the rear of the pan. We know these engines can starve for oil on hard launches so I wanted to correct this and honestly didnt want to spend 200 on Improved Racing's baffle. The main cap bolts are about 4.5 inches apart, and since the support bolts to them I figure why not just move it back one....So I cut the tube and remounted it...
![Name: 20170703_143845_zps1otwjfwn.jpeg
Views: 4449
Size: 321.6 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583421d1501199149-updated-three-trips-tnt-pics-vids-20170703_143845_zps1otwjfwn.jpeg)
Grabbed the old pickup tube that came with the engine and hacked a piece out and welded it in.
![Name: 20170703_161407_zpspgn1joyq.jpeg
Views: 4422
Size: 288.2 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583422d1501199149-updated-three-trips-tnt-pics-vids-20170703_161407_zpspgn1joyq.jpeg)
That was pretty easy, now we have to alter the pan to make it work. Here is the stock baffle, as you can see the pickup is in the center of the motor but in the front of the pan's sump. That is great for braking, and probably decent for corners, but poor for hard acceleration.
![Name: 20170703_142525_zpsxdprvmyc.jpeg
Views: 4396
Size: 789.1 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583423d1501199149-updated-three-trips-tnt-pics-vids-20170703_142525_zpsxdprvmyc.jpeg)
Under the bolt in baffle there is a casted in V shape. That is the way it combats acceleration forces. Some oil gets through the center but most is forced to the sides and is sort of trapped, and at the very least slowed down from going rearward. This probably works, but only so good. It had to be cut because thats where the pickup will be located now. Also notice the new -10AN drain for the turbo, more on that in a bit.
![Name: 20170703_161421_zpsrrclli7i.jpeg
Views: 4442
Size: 855.4 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583424d1501199149-updated-three-trips-tnt-pics-vids-20170703_161421_zpsrrclli7i.jpeg)
This is what was left after everything was clearanced. The hump that was on the right had to be removed for the tubing to clear, and I added the crossbar in the back to help keep the oil from going up the back of the engine during acceleration. Not pretty but functional. I just used flat bar I had laying around.
![Name: 20170703_164947_zps814ra6ty.jpeg
Views: 4442
Size: 314.3 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583425d1501199149-updated-three-trips-tnt-pics-vids-20170703_164947_zps814ra6ty.jpeg)
Then I realized I've just shifted my issues, now I may lose pressure during braking. So i pulled the baffle back out, bent two little sheet metal V flaps, and made two more crossbar flats across the top. The idea was to essentially reverse the stock idea, pickup in the back and control the oil going forward. Not pretty but functional.
![Name: 20170704_151213_zps6nreu6uo.jpeg
Views: 4512
Size: 1.14 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583426d1501199149-updated-three-trips-tnt-pics-vids-20170704_151213_zps6nreu6uo.jpeg)
Now I wanted to do something fun. Lets see how much oil this pan can hold. Also, I wanted to know what level I could be at and still have the turbo drain properly.
6 Quarts:
![Name: 20170704_142620_zpsqbmltsni.jpeg
Views: 4508
Size: 1.04 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583427d1501199149-updated-three-trips-tnt-pics-vids-20170704_142620_zpsqbmltsni.jpeg)
7 Quarts:
![Name: 20170704_142724_zpszohli8wp.jpeg
Views: 4412
Size: 127.1 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583428d1501199149-updated-three-trips-tnt-pics-vids-20170704_142724_zpszohli8wp.jpeg)
8 Quarts:
![Name: 20170704_142819_zpsrb407swc.jpeg
Views: 4410
Size: 1.01 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583429d1501199149-updated-three-trips-tnt-pics-vids-20170704_142819_zpsrb407swc.jpeg)
Pan held level and 9 Quarts:
![Name: 20170704_142911_zps4fd4lpus.jpeg
Views: 4418
Size: 114.0 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583430d1501199149-updated-three-trips-tnt-pics-vids-20170704_142911_zps4fd4lpus.jpeg)
So we know my turbo will drain with the 7 quarts i plan on running, but what about windage, where is the crank in all of this?
![Name: 20170704_143107_zpsj4t21ojj.jpeg
Views: 4474
Size: 1.05 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583431d1501199149-updated-three-trips-tnt-pics-vids-20170704_143107_zpsj4t21ojj.jpeg)
1.5 inches into the pan. Let's see how that hits the marks we just made.
![Name: 20170704_143211_zpsq1qvqaas.jpeg
Views: 4484
Size: 106.8 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583432d1501199149-updated-three-trips-tnt-pics-vids-20170704_143211_zpsq1qvqaas.jpeg)
I got the feed for the turbo tapped in above the oil filter with a 1/8NPT to -4AN fitting. Also got these in, these are for the 4l80e, and will convert the cooler outlets to -8AN which is what I have in the car currently.
![Name: 20170704_220743_zpsvpmwourj.jpeg
Views: 4458
Size: 1.06 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583433d1501199149-updated-three-trips-tnt-pics-vids-20170704_220743_zpsvpmwourj.jpeg)
Stay tuned, more to come.
![Burnout](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_burnout.gif)
Got a few things done on my days off. First, i knew a had a mismatch on injectors/rails. What I have is car injectors, a truck intake, and truck billet rails. Here's the height difference.
![Name: 20170703_131123_zpsszkrkk1s.jpeg
Views: 4520
Size: 1,015.0 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583417d1501199149-updated-three-trips-tnt-pics-vids-20170703_131123_zpsszkrkk1s.jpeg)
After mocking it up and seeing the space between the rail and the intake, I measured that i needed 4 .850 spacers. I went to Home Depot and got some 1/2" square and round tubing. After playing with them I decided I like the square tubing better, so I made 4 spacers and bought 4 longer bolts. I believe they were m6x1.0x40mm.
![Name: 20170703_133952_zpsnrjmcoa1.jpeg
Views: 4437
Size: 141.3 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583418d1501199149-updated-three-trips-tnt-pics-vids-20170703_133952_zpsnrjmcoa1.jpeg)
Both sides on, crossover installed, they fit nice.
![Name: 20170703_140550_zpsprrumab7.jpeg
Views: 4491
Size: 1.13 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583419d1501199149-updated-three-trips-tnt-pics-vids-20170703_140550_zpsprrumab7.jpeg)
Spin the motor over. I'm not gonna use or need the low oil sensor thats in the pan, so I'm gonna remove it and buy a plug. Cruising around ebay searching that size I realize someone makes a plug specifically for this, so I bought it. This is not tapered thread so an oring must be used.
![Name: 20170703_153303_zpsc486e1qa.jpeg
Views: 4456
Size: 846.6 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583420d1501199149-updated-three-trips-tnt-pics-vids-20170703_153303_zpsc486e1qa.jpeg)
Didnt get a complete "before" pic, but i decided to move the oil sump to the rear of the pan. We know these engines can starve for oil on hard launches so I wanted to correct this and honestly didnt want to spend 200 on Improved Racing's baffle. The main cap bolts are about 4.5 inches apart, and since the support bolts to them I figure why not just move it back one....So I cut the tube and remounted it...
![Name: 20170703_143845_zps1otwjfwn.jpeg
Views: 4449
Size: 321.6 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583421d1501199149-updated-three-trips-tnt-pics-vids-20170703_143845_zps1otwjfwn.jpeg)
Grabbed the old pickup tube that came with the engine and hacked a piece out and welded it in.
![Name: 20170703_161407_zpspgn1joyq.jpeg
Views: 4422
Size: 288.2 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583422d1501199149-updated-three-trips-tnt-pics-vids-20170703_161407_zpspgn1joyq.jpeg)
That was pretty easy, now we have to alter the pan to make it work. Here is the stock baffle, as you can see the pickup is in the center of the motor but in the front of the pan's sump. That is great for braking, and probably decent for corners, but poor for hard acceleration.
![Name: 20170703_142525_zpsxdprvmyc.jpeg
Views: 4396
Size: 789.1 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583423d1501199149-updated-three-trips-tnt-pics-vids-20170703_142525_zpsxdprvmyc.jpeg)
Under the bolt in baffle there is a casted in V shape. That is the way it combats acceleration forces. Some oil gets through the center but most is forced to the sides and is sort of trapped, and at the very least slowed down from going rearward. This probably works, but only so good. It had to be cut because thats where the pickup will be located now. Also notice the new -10AN drain for the turbo, more on that in a bit.
![Name: 20170703_161421_zpsrrclli7i.jpeg
Views: 4442
Size: 855.4 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583424d1501199149-updated-three-trips-tnt-pics-vids-20170703_161421_zpsrrclli7i.jpeg)
This is what was left after everything was clearanced. The hump that was on the right had to be removed for the tubing to clear, and I added the crossbar in the back to help keep the oil from going up the back of the engine during acceleration. Not pretty but functional. I just used flat bar I had laying around.
![Name: 20170703_164947_zps814ra6ty.jpeg
Views: 4442
Size: 314.3 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583425d1501199149-updated-three-trips-tnt-pics-vids-20170703_164947_zps814ra6ty.jpeg)
Then I realized I've just shifted my issues, now I may lose pressure during braking. So i pulled the baffle back out, bent two little sheet metal V flaps, and made two more crossbar flats across the top. The idea was to essentially reverse the stock idea, pickup in the back and control the oil going forward. Not pretty but functional.
![Name: 20170704_151213_zps6nreu6uo.jpeg
Views: 4512
Size: 1.14 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583426d1501199149-updated-three-trips-tnt-pics-vids-20170704_151213_zps6nreu6uo.jpeg)
Now I wanted to do something fun. Lets see how much oil this pan can hold. Also, I wanted to know what level I could be at and still have the turbo drain properly.
6 Quarts:
![Name: 20170704_142620_zpsqbmltsni.jpeg
Views: 4508
Size: 1.04 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583427d1501199149-updated-three-trips-tnt-pics-vids-20170704_142620_zpsqbmltsni.jpeg)
7 Quarts:
![Name: 20170704_142724_zpszohli8wp.jpeg
Views: 4412
Size: 127.1 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583428d1501199149-updated-three-trips-tnt-pics-vids-20170704_142724_zpszohli8wp.jpeg)
8 Quarts:
![Name: 20170704_142819_zpsrb407swc.jpeg
Views: 4410
Size: 1.01 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583429d1501199149-updated-three-trips-tnt-pics-vids-20170704_142819_zpsrb407swc.jpeg)
Pan held level and 9 Quarts:
![Name: 20170704_142911_zps4fd4lpus.jpeg
Views: 4418
Size: 114.0 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583430d1501199149-updated-three-trips-tnt-pics-vids-20170704_142911_zps4fd4lpus.jpeg)
So we know my turbo will drain with the 7 quarts i plan on running, but what about windage, where is the crank in all of this?
![Name: 20170704_143107_zpsj4t21ojj.jpeg
Views: 4474
Size: 1.05 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583431d1501199149-updated-three-trips-tnt-pics-vids-20170704_143107_zpsj4t21ojj.jpeg)
1.5 inches into the pan. Let's see how that hits the marks we just made.
![Name: 20170704_143211_zpsq1qvqaas.jpeg
Views: 4484
Size: 106.8 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583432d1501199149-updated-three-trips-tnt-pics-vids-20170704_143211_zpsq1qvqaas.jpeg)
I got the feed for the turbo tapped in above the oil filter with a 1/8NPT to -4AN fitting. Also got these in, these are for the 4l80e, and will convert the cooler outlets to -8AN which is what I have in the car currently.
![Name: 20170704_220743_zpsvpmwourj.jpeg
Views: 4458
Size: 1.06 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583433d1501199149-updated-three-trips-tnt-pics-vids-20170704_220743_zpsvpmwourj.jpeg)
Stay tuned, more to come.
Last edited by 01ssreda4; 07-10-2017 at 05:01 PM.
#349
TECH Senior Member
Thread Starter
iTrader: (96)
Join Date: Aug 2007
Location: Turnin' Wrenches Infractions: 005
Posts: 24,240
Likes: 0
Received 81 Likes
on
72 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Ok got some more parts in, on the left is a manual boost controller, top right is some -8 ORB AN fittings for the fuel rails, and the bottom right is a weldable 1/8 NPT bung for the trans pan.
![Name: 20170710_202744_zpss1yjn7wv.jpeg
Views: 4479
Size: 831.2 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583207d1501198233-updated-three-trips-tnt-pics-vids-20170710_202744_zpss1yjn7wv.jpeg)
PST forged yoke for the 4l80e on the left and the stocker on the right. Im going to swap this onto my existing PST shaft.
![Name: 20170710_202836_zps8ixefz4v.jpeg
Views: 4531
Size: 856.3 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583208d1501198233-updated-three-trips-tnt-pics-vids-20170710_202836_zps8ixefz4v.jpeg)
My 80e output shaft has an oring, your yoke needs to have a smooth lip to seal on it.
![Name: 20170710_202847_zpsnccgsidf.jpeg
Views: 4556
Size: 1.12 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583209d1501198233-updated-three-trips-tnt-pics-vids-20170710_202847_zpsnccgsidf.jpeg)
![Name: 20170710_194402_zpsxvwry8xb.jpeg
Views: 4493
Size: 1.11 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583211d1501198233-updated-three-trips-tnt-pics-vids-20170710_194402_zpsxvwry8xb.jpeg)
Vacuum block, yes its colorful![The Jester](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_jest.gif)
![Name: 20170710_202559_zpsvfi5xx2a.jpeg
Views: 4423
Size: 860.1 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583212d1501198233-updated-three-trips-tnt-pics-vids-20170710_202559_zpsvfi5xx2a.jpeg)
Basically the converter I bought will work with almost any LS flexplate because it has two (6 bolt) bolt patterns on it. So I didn't actually need to buy a flexplate, but I wanted to at minimum use all 6 bolts, where the stock 60e plate thats on the engine is only 3 bolts. This is an aftermarket 80e plate with all 6 holes part number ATP Z-270. The reason you see this and stuff like the manual boost controller, not welding fittings in is because I'm trying to trim expense where I can. This can get out of control with all the little bullshit things that would have to do/buy. Im basically trying to stretch this last bit as far as I can.
![Name: 20170710_203021_zpsjavwwynp.jpeg
Views: 4480
Size: 1.09 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583213d1501198233-updated-three-trips-tnt-pics-vids-20170710_203021_zpsjavwwynp.jpeg)
This is Chrs1313 dual 450 pumps. I also bought the hotwire harness so installation should be simple.
![Name: 20170708_181541_zpsv5v7clza.jpeg
Views: 4493
Size: 968.7 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583214d1501198233-updated-three-trips-tnt-pics-vids-20170708_181541_zpsv5v7clza.jpeg)
Aeromotive 13303 fuel pressure regulator, this is -8AN in and out.
![Name: 20170708_181554_zps5rwo2ysx.jpeg
Views: 4456
Size: 1.10 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583216d1501198233-updated-three-trips-tnt-pics-vids-20170708_181554_zps5rwo2ysx.jpeg)
Here is the plug for the oil pan. Bought from ICT Billet on ebay.
![Name: 20170708_160633_zpsuyagg42v.jpeg
Views: 4494
Size: 1.04 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583217d1501198233-updated-three-trips-tnt-pics-vids-20170708_160633_zpsuyagg42v.jpeg)
I took the valve covers off and drilled a hole in them. I also cut and removed some of the baffles.
![Name: 20170708_144832_zpsw3egtofj.jpeg
Views: 4380
Size: 992.0 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583218d1501198233-updated-three-trips-tnt-pics-vids-20170708_144832_zpsw3egtofj.jpeg)
Installed a -10AN fitting for the breather. Went back after this pic and removed all the baffling, decided it was now useless lets get rid of it.
![Name: 20170708_152353_zpsnxpyx6v8.jpeg
Views: 4492
Size: 1.12 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583219d1501198233-updated-three-trips-tnt-pics-vids-20170708_152353_zpsnxpyx6v8.jpeg)
I did one on each side to go the the catch can.
![Name: 20170708_163421_zpsgm4eqdou.jpeg
Views: 4426
Size: 852.9 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583221d1501198233-updated-three-trips-tnt-pics-vids-20170708_163421_zpsgm4eqdou.jpeg)
Pulled the harness off the bracket and trimmed the center metal out. Seems like an easy no weld solution. Once we get a little closer to finished I will probably buy a 90 degree -10 fitting for both covers.
![Name: 20170710_202744_zpss1yjn7wv.jpeg
Views: 4479
Size: 831.2 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583207d1501198233-updated-three-trips-tnt-pics-vids-20170710_202744_zpss1yjn7wv.jpeg)
PST forged yoke for the 4l80e on the left and the stocker on the right. Im going to swap this onto my existing PST shaft.
![Name: 20170710_202836_zps8ixefz4v.jpeg
Views: 4531
Size: 856.3 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583208d1501198233-updated-three-trips-tnt-pics-vids-20170710_202836_zps8ixefz4v.jpeg)
My 80e output shaft has an oring, your yoke needs to have a smooth lip to seal on it.
![Name: 20170710_202847_zpsnccgsidf.jpeg
Views: 4556
Size: 1.12 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583209d1501198233-updated-three-trips-tnt-pics-vids-20170710_202847_zpsnccgsidf.jpeg)
![Name: 20170710_194402_zpsxvwry8xb.jpeg
Views: 4493
Size: 1.11 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583211d1501198233-updated-three-trips-tnt-pics-vids-20170710_194402_zpsxvwry8xb.jpeg)
Vacuum block, yes its colorful
![The Jester](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_jest.gif)
![Name: 20170710_202559_zpsvfi5xx2a.jpeg
Views: 4423
Size: 860.1 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583212d1501198233-updated-three-trips-tnt-pics-vids-20170710_202559_zpsvfi5xx2a.jpeg)
Basically the converter I bought will work with almost any LS flexplate because it has two (6 bolt) bolt patterns on it. So I didn't actually need to buy a flexplate, but I wanted to at minimum use all 6 bolts, where the stock 60e plate thats on the engine is only 3 bolts. This is an aftermarket 80e plate with all 6 holes part number ATP Z-270. The reason you see this and stuff like the manual boost controller, not welding fittings in is because I'm trying to trim expense where I can. This can get out of control with all the little bullshit things that would have to do/buy. Im basically trying to stretch this last bit as far as I can.
![Name: 20170710_203021_zpsjavwwynp.jpeg
Views: 4480
Size: 1.09 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583213d1501198233-updated-three-trips-tnt-pics-vids-20170710_203021_zpsjavwwynp.jpeg)
This is Chrs1313 dual 450 pumps. I also bought the hotwire harness so installation should be simple.
![Name: 20170708_181541_zpsv5v7clza.jpeg
Views: 4493
Size: 968.7 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583214d1501198233-updated-three-trips-tnt-pics-vids-20170708_181541_zpsv5v7clza.jpeg)
Aeromotive 13303 fuel pressure regulator, this is -8AN in and out.
![Name: 20170708_181554_zps5rwo2ysx.jpeg
Views: 4456
Size: 1.10 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583216d1501198233-updated-three-trips-tnt-pics-vids-20170708_181554_zps5rwo2ysx.jpeg)
Here is the plug for the oil pan. Bought from ICT Billet on ebay.
![Name: 20170708_160633_zpsuyagg42v.jpeg
Views: 4494
Size: 1.04 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583217d1501198233-updated-three-trips-tnt-pics-vids-20170708_160633_zpsuyagg42v.jpeg)
I took the valve covers off and drilled a hole in them. I also cut and removed some of the baffles.
![Name: 20170708_144832_zpsw3egtofj.jpeg
Views: 4380
Size: 992.0 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583218d1501198233-updated-three-trips-tnt-pics-vids-20170708_144832_zpsw3egtofj.jpeg)
Installed a -10AN fitting for the breather. Went back after this pic and removed all the baffling, decided it was now useless lets get rid of it.
![Name: 20170708_152353_zpsnxpyx6v8.jpeg
Views: 4492
Size: 1.12 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583219d1501198233-updated-three-trips-tnt-pics-vids-20170708_152353_zpsnxpyx6v8.jpeg)
I did one on each side to go the the catch can.
![Name: 20170708_163421_zpsgm4eqdou.jpeg
Views: 4426
Size: 852.9 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583221d1501198233-updated-three-trips-tnt-pics-vids-20170708_163421_zpsgm4eqdou.jpeg)
Pulled the harness off the bracket and trimmed the center metal out. Seems like an easy no weld solution. Once we get a little closer to finished I will probably buy a 90 degree -10 fitting for both covers.
![Name: 20170708_152343_zpsavwvqymx.jpeg
Views: 4447
Size: 1,016.5 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583225d1501198233-updated-three-trips-tnt-pics-vids-20170708_152343_zpsavwvqymx.jpeg)
#351
TECH Senior Member
Thread Starter
iTrader: (96)
Join Date: Aug 2007
Location: Turnin' Wrenches Infractions: 005
Posts: 24,240
Likes: 0
Received 81 Likes
on
72 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I know, gonna run that one with 6 bolts for now.
Couple of things though, Im really not looking to turn a ton of rpm, and turbos do bring their powerband in slow and I dont believe I will best my NA 60ft time so it should be fine.
![Bomb](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_bomb.gif)
#354
TECH Senior Member
Thread Starter
iTrader: (96)
Join Date: Aug 2007
Location: Turnin' Wrenches Infractions: 005
Posts: 24,240
Likes: 0
Received 81 Likes
on
72 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Started with the transmission, pressure washed it, and painted it. You cant see in this pic but the 1/8 NPT temp bung is welded in. I put a little rtv on both sides of the gasket before i laid the pan on.
![Name: 20170714_100742_zpsedp1sqsn.jpeg
Views: 4433
Size: 937.5 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583120d1501198233-updated-three-trips-tnt-pics-vids-20170714_100742_zpsedp1sqsn.jpeg)
I also installed a new output shaft seal and test fit the new DS yoke.
![Name: 20170714_102546_zpsxymuwetu.jpeg
Views: 4467
Size: 252.5 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583121d1501198233-updated-three-trips-tnt-pics-vids-20170714_102546_zpsxymuwetu.jpeg)
The gauge came with a red light cover which i had to light up and try out.
![Name: 20170714_125731_zpshc0ynguv.jpeg
Views: 4379
Size: 338.0 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583122d1501198233-updated-three-trips-tnt-pics-vids-20170714_125731_zpshc0ynguv.jpeg)
This is a Nelson 60e to 80e conversion harness. You can see it has the wiring for the extra speed sensor that the 4l80s have.
![Name: 20170714_125509_zpsbqmjl1jv.jpeg
Views: 4410
Size: 803.7 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583123d1501198233-updated-three-trips-tnt-pics-vids-20170714_125509_zpsbqmjl1jv.jpeg)
Pushrods came in, so I installed those, torqued the rockers down, installed new valve cover gaskets. The pushrods were an ebay score, new without box, about $70, they are Manley brand. After that I decided lets do something a little more fun......So I got out the air grinder...
![Name: 20170714_113121_zpspdnm2bu3.jpeg
Views: 4448
Size: 1.11 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583124d1501198233-updated-three-trips-tnt-pics-vids-20170714_113121_zpspdnm2bu3.jpeg)
The ring is 4.25", this is a 3.5" pipe. I think it looks fine, but most people I talk to think it would look better 4".....
![Name: 20170714_150516_zpssy9ksl3n.jpeg
Views: 4457
Size: 1.12 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583125d1501198233-updated-three-trips-tnt-pics-vids-20170714_150516_zpssy9ksl3n.jpeg)
These pics with flash make the car look filthy, of course some of this hasnt seen the light of day since the car was new. Working under the hood I removed the fuel lines in the engine bay, and removed the ABS delete that was install (linelock and proportioning valve), and removed the master cylinder and brake booster off the firewall. It will be replaced with a Strange manual master and a couple of new short lines that dont run around to the front of the strut tower.
![Name: 20170714_145550_zpso0msjvoi.jpeg
Views: 4439
Size: 1.16 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583126d1501198233-updated-three-trips-tnt-pics-vids-20170714_145550_zpso0msjvoi.jpeg)
Pulled the battery, battery tray, and coolant jug. There is a little rust under there so I'm gonna clean this up and possibly paint, havent decided yet. This is standing at the driver headlight looking at where the battery sits.
![Name: 20170714_113020_zpslsmwatab.jpeg
Views: 4370
Size: 1.06 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583127d1501198233-updated-three-trips-tnt-pics-vids-20170714_113020_zpslsmwatab.jpeg)
I was looking at coolant expansion tanks and really really liked the Moroso aluminum ones. But not being able to justify the $110 I opted for this Dorman for $9 shipped. I like the fact that I can see the level through it. My initial thinking is since Im running the small battery maybe they can share the space? Here's my brainstorming........this is standing at the passenger fender looking straight down.
![Name: 20170714_113052_zpsajar3fzz.jpeg
Views: 4320
Size: 91.3 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583128d1501198233-updated-three-trips-tnt-pics-vids-20170714_113052_zpsajar3fzz.jpeg)
Circle D converter shipped yesterday and still more parts on the way.....Thorough engine bay cleaning coming up next!!!
![Name: 20170714_100742_zpsedp1sqsn.jpeg
Views: 4433
Size: 937.5 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583120d1501198233-updated-three-trips-tnt-pics-vids-20170714_100742_zpsedp1sqsn.jpeg)
I also installed a new output shaft seal and test fit the new DS yoke.
![Name: 20170714_102546_zpsxymuwetu.jpeg
Views: 4467
Size: 252.5 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583121d1501198233-updated-three-trips-tnt-pics-vids-20170714_102546_zpsxymuwetu.jpeg)
The gauge came with a red light cover which i had to light up and try out.
![Name: 20170714_125731_zpshc0ynguv.jpeg
Views: 4379
Size: 338.0 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583122d1501198233-updated-three-trips-tnt-pics-vids-20170714_125731_zpshc0ynguv.jpeg)
This is a Nelson 60e to 80e conversion harness. You can see it has the wiring for the extra speed sensor that the 4l80s have.
![Name: 20170714_125509_zpsbqmjl1jv.jpeg
Views: 4410
Size: 803.7 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583123d1501198233-updated-three-trips-tnt-pics-vids-20170714_125509_zpsbqmjl1jv.jpeg)
Pushrods came in, so I installed those, torqued the rockers down, installed new valve cover gaskets. The pushrods were an ebay score, new without box, about $70, they are Manley brand. After that I decided lets do something a little more fun......So I got out the air grinder...
![Name: 20170714_113121_zpspdnm2bu3.jpeg
Views: 4448
Size: 1.11 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583124d1501198233-updated-three-trips-tnt-pics-vids-20170714_113121_zpspdnm2bu3.jpeg)
The ring is 4.25", this is a 3.5" pipe. I think it looks fine, but most people I talk to think it would look better 4".....
![Name: 20170714_150516_zpssy9ksl3n.jpeg
Views: 4457
Size: 1.12 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583125d1501198233-updated-three-trips-tnt-pics-vids-20170714_150516_zpssy9ksl3n.jpeg)
These pics with flash make the car look filthy, of course some of this hasnt seen the light of day since the car was new. Working under the hood I removed the fuel lines in the engine bay, and removed the ABS delete that was install (linelock and proportioning valve), and removed the master cylinder and brake booster off the firewall. It will be replaced with a Strange manual master and a couple of new short lines that dont run around to the front of the strut tower.
![Name: 20170714_145550_zpso0msjvoi.jpeg
Views: 4439
Size: 1.16 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583126d1501198233-updated-three-trips-tnt-pics-vids-20170714_145550_zpso0msjvoi.jpeg)
Pulled the battery, battery tray, and coolant jug. There is a little rust under there so I'm gonna clean this up and possibly paint, havent decided yet. This is standing at the driver headlight looking at where the battery sits.
![Name: 20170714_113020_zpslsmwatab.jpeg
Views: 4370
Size: 1.06 MB](https://ls1tech.com/forums/attachments/multimedia-exchange/583127d1501198233-updated-three-trips-tnt-pics-vids-20170714_113020_zpslsmwatab.jpeg)
I was looking at coolant expansion tanks and really really liked the Moroso aluminum ones. But not being able to justify the $110 I opted for this Dorman for $9 shipped. I like the fact that I can see the level through it. My initial thinking is since Im running the small battery maybe they can share the space? Here's my brainstorming........this is standing at the passenger fender looking straight down.
![Name: 20170714_113052_zpsajar3fzz.jpeg
Views: 4320
Size: 91.3 KB](https://ls1tech.com/forums/attachments/multimedia-exchange/583128d1501198233-updated-three-trips-tnt-pics-vids-20170714_113052_zpsajar3fzz.jpeg)
Circle D converter shipped yesterday and still more parts on the way.....Thorough engine bay cleaning coming up next!!!
Last edited by 01ssreda4; 07-15-2017 at 08:00 AM.
#359
TECH Senior Member
Thread Starter
iTrader: (96)
Join Date: Aug 2007
Location: Turnin' Wrenches Infractions: 005
Posts: 24,240
Likes: 0
Received 81 Likes
on
72 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Hughes has one also. Guarantee they are no better then this one I got for 45. One company just went through the trouble of having it certified and another didnt. I ran a cat stamped SFI plate in my H/C/I combo and they weren't know to be the greatest thing, yet they still had a legit sticker on them.