High revving V8's
#21
More proof that it didnt happen. No way stock cast heads would flow enough to rev past 7k. The cam is too big for the heads too. Not having any mercy on cars would not help that anchor of an engine rev to over 9k. Sorry it didnt happen.
#23
Originally Posted by fbody83
Anyone have any racing or dyno vids of v8's revving over 7000? I love the sound of them! I have this one vid of a camaro and a bike racing and in the end the camaro sounds like he rev's to high hell. Anyone have any info on this car or know them?
http://media.putfile.com/Camaro-w-n2o-vs-CBR600f4i
http://media.putfile.com/Camaro-w-n2o-vs-CBR600f4i
His car pushes over 7000. I have another video of him racing a BPU supra reving to 7200. Great sounding setup, Lt's and x pipe duals
#25
TECH Apprentice
iTrader: (4)
Join Date: Jan 2004
Location: Chi-Town
Posts: 339
Likes: 0
Received 0 Likes
on
0 Posts
i spin my 383 LT1 past 8000, shifting at 8000 on spray, and i do drive it on the street. i will see if i can post a vid or you can find the MFBA dyno day at speed inc vid on this sight, its a green formula.
#26
TECH Addict
iTrader: (8)
first engine i ever built was a 355 (12 years ago), rebuilt stock bottom end. hyd .480 cam stock heads w/ the right springs. In a car w/ 4.56 gears I accidentally took it past 8k a few times. went there with ease. 1st gear was a killer. no rev limiter or anything. but its possible. Ive heard of basically stock 350s running insane rpms. Not lasting long but they did it.
#28
Teching In
Join Date: Jun 2005
Location: omaha, nebraska
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
ya i bent a couple push rods spun a rocker arm the 1st time i pushed the engine that far i just recently torn down the engine every thing looked good
the cylinder walls were a little wavey
bearings were good
my new setup is
same block punched 40 over
forged speed pro pistons and rings
clevite 77 bearings
scat nodular crank
stock **** rods 5.7
dart iron eagal heads 2.05in/1.60ex
hardend pushrods
1.5 roller rockers
edlbrook tunnel ram
2 450cfm holleys
doug herbert cam 320dur 5.88lift
will see how that holds up this summer
the cylinder walls were a little wavey
bearings were good
my new setup is
same block punched 40 over
forged speed pro pistons and rings
clevite 77 bearings
scat nodular crank
stock **** rods 5.7
dart iron eagal heads 2.05in/1.60ex
hardend pushrods
1.5 roller rockers
edlbrook tunnel ram
2 450cfm holleys
doug herbert cam 320dur 5.88lift
will see how that holds up this summer
#31
TECH Junkie
Join Date: Jan 2002
Location: At the office
Posts: 3,015
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by fbody83
#32
Launching!
I think i have seen that Verbs guy a few times too. But he was always losing to some guy in a wheelchair. BTW, we need that portion of the video of you and Bryce racing when we put the handicap symbol on the back glass. Load it on here.
#33
TECH Junkie
Join Date: Jan 2002
Location: At the office
Posts: 3,015
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by lt1camaro95
I think i have seen that Verbs guy a few times too. But he was always losing to some guy in a wheelchair. BTW, we need that portion of the video of you and Bryce racing when we put the handicap symbol on the back glass. Load it on here.