99 camaro ss feeling slow
#1
TECH Fanatic
Thread Starter
iTrader: (1)
Join Date: Mar 2005
Location: Central jersey, nj
Posts: 1,688
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I have a 99 camaro m6 that has 95k on it. I bought it a few weeks ago and it felt down on power compared to my 01 camaro. So far i put on headers with a ory that goes through the stock slp dual dual exhaust and replaced the spark plugs and o2 sensors. the car felt a lot faster than original, but still not up to what i think it should be. So I went to the track and ran a best of 15.1 at 96...lol. The y pipe hits the floor pretty bad when I was launching, which I think cause the knock sensors to read false knock and pull a lot of timing. After I left the track...if I woulod roll into first at 30 mph and car would pull a lot harder through the gears.
So is the y pipe my problem? Or should I be looking at something else? Maybe cleaning the maf sensor? fuel filter? fuel injectors? maybe find someone with a scan gauge?
thanks!
So is the y pipe my problem? Or should I be looking at something else? Maybe cleaning the maf sensor? fuel filter? fuel injectors? maybe find someone with a scan gauge?
thanks!
#3
TECH Fanatic
Thread Starter
iTrader: (1)
Join Date: Mar 2005
Location: Central jersey, nj
Posts: 1,688
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
95k...what is a full tune up? I did spark plugs and o2 sensors already and felt a huge improvement. How much timing can the ecu pull if it thinks there is knock?
#4
Teching In
Join Date: Jun 2010
Location: Poinciana, Florida
Posts: 44
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Plug Wires
Oil Change
Oil Filter
Z-Max Micro Lubricant (Highly Recommended)
Injector Cleaners/Fuel System Cleaning
Radiator And Coolant Flush
Transmission Fluid Change
Air Filter
Also Buy any Hoses That Look Worn, If the Belt Looks Bad You Might Want to Replace That. Just A Basic List, Everything Can Be Found At Autozone Or your Local Auto Parts Store. If I'm Missing Anything Someone Else On This Forum will Catch It
![Winky](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_wink.gif)
#6
TECH Fanatic
Thread Starter
iTrader: (1)
Join Date: Mar 2005
Location: Central jersey, nj
Posts: 1,688
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
How much timing can the ecu pull if it reads knock?
#7
Teching In
Join Date: Jun 2010
Location: Poinciana, Florida
Posts: 44
Likes: 0
Received 0 Likes
on
0 Posts
Trending Topics
#10
TECH Fanatic
Thread Starter
iTrader: (1)
Join Date: Mar 2005
Location: Central jersey, nj
Posts: 1,688
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
cleaned the maf sensor today...to say it was dirty would be an understatement. there was about 6 bugs in the screen part and the wires were completely black and having gunk on them. Car feels a lot better...but still feels soft if i launch...
#14
LS1Tech Administrator
iTrader: (3)
Join Date: Nov 2001
Location: Schiller Park, IL Member: #317
Posts: 32,318
Likes: 0
Received 1,752 Likes
on
1,252 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech20year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Oil additives are crap for the most part. Steer clear IMO. The only possibile exception would be something like ZDDP for the old flat tappet cammed engines, since most modern oils seem to be reducing zinc content. Even still, I'd rather just stick to a specialty oil like VR-1 that has the proper base structure for old engine applications.
This is often the result of K&N-type filter use. People over-oil them, and this is what happens over time. I'd rather just stick with paper for any applications that use an MAF. And if you absolutely insist on getting that 0.5 hp gain from the K&N, then make sure to check/clean the MAF on a somewhat regular basis (at least with every plug change).
This is often the result of K&N-type filter use. People over-oil them, and this is what happens over time. I'd rather just stick with paper for any applications that use an MAF. And if you absolutely insist on getting that 0.5 hp gain from the K&N, then make sure to check/clean the MAF on a somewhat regular basis (at least with every plug change).
#17
Teching In
Join Date: Jun 2010
Location: Poinciana, Florida
Posts: 44
Likes: 0
Received 0 Likes
on
0 Posts
#18
LS1Tech Administrator
iTrader: (3)
Join Date: Nov 2001
Location: Schiller Park, IL Member: #317
Posts: 32,318
Likes: 0
Received 1,752 Likes
on
1,252 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech20year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Don't worry, lots of people have fallen victim to the claims of oil additives. Some of these products end up being harmless, while some are actually bad for the engine. But one thing they all have in common is they rarely do any good whatsoever.
Just stick to a good quality oil that's right for your application and change it regularly.
Just stick to a good quality oil that's right for your application and change it regularly.
#19
Teching In
Join Date: Jun 2010
Location: Poinciana, Florida
Posts: 44
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Don't worry, lots of people have fallen victim to the claims of oil additives. Some of these products end up being harmless, while some are actually bad for the engine. But one thing they all have in common is they rarely do any good whatsoever.
Just stick to a good quality oil that's right for your application and change it regularly.
Just stick to a good quality oil that's right for your application and change it regularly.
We Use It If We Can't Find 93 Octane.
#20
11 Second Club
iTrader: (18)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
very few octane boosters do enough to raise it any...
1 point of octane boost is actually .1 octane number so most add less than 1 octane number (Ie change 87 to 88)
N.O.S. have some out that are supposed to raise it by 30 or more points, which might be worthwhile for emergencies
1 point of octane boost is actually .1 octane number so most add less than 1 octane number (Ie change 87 to 88)
N.O.S. have some out that are supposed to raise it by 30 or more points, which might be worthwhile for emergencies