need help fast....t/b question
#1
On The Tree
Thread Starter
iTrader: (9)
Join Date: Jul 2006
Posts: 151
Likes: 0
Received 0 Likes
on
0 Posts
need help fast....t/b question
ok, i bought a ported t/b from a user here who said it was a 00...He also said he had used it on his 98..which i didnt think would work...anyways...i just installed it on my car which is also a 00...cams on the t/b are the same size so i figure it is from a 00....The t/b had the bump stop mod done to it also...I just put it on my car and my car will not stay running...will go when gas is depressed but will not idle, just dies......Can the screw be adjusted to make it work or has it probly been ground down too much with the bump stop mod...Thanks,,oh yea when i gave it some gas the car kinda back fired..
#3
12 Second Club
iTrader: (49)
i think, 2000+ had an idle adjustment screw. if not, you may have to make the computer relearn the idle. unplug the TPS and IAC, turn the key on/run position, (dont start) and leave it for a few minutes. then come back, turn the key off, plug the sensors back in and turn it on for a few more minutes. come back and start the car.
#6
Moderator
iTrader: (4)
Join Date: Nov 2003
Location: Plainfield, CT
Posts: 10,520
Likes: 0
Received 0 Likes
on
0 Posts
Check the hole in the TB blade and compare it to the one in your stocker. It may have been drilled out for a Cammed car.
I would disconnect the battery ground. Unplug all the sensors and make sure they are in correctly. Reconnect the battery. Make sure your PCV hose is connected. restart the car and see what happens.
I would disconnect the battery ground. Unplug all the sensors and make sure they are in correctly. Reconnect the battery. Make sure your PCV hose is connected. restart the car and see what happens.
Trending Topics
#8
On The Tree
Thread Starter
iTrader: (9)
Join Date: Jul 2006
Posts: 151
Likes: 0
Received 0 Likes
on
0 Posts
..
the holes look the same...i did forget to push back in one of the coolant hoses...drvr side bottom...i pushed it back on and it still does it....i am trying the tps and iac as we speak...how long should i wait ..
#13
On The Tree
Thread Starter
iTrader: (9)
Join Date: Jul 2006
Posts: 151
Likes: 0
Received 0 Likes
on
0 Posts
idle
yea it idles around 400, if i give it gas and let off it goes to around 300 and then comes back up to around 400....should i adjust that screw or is there another way to handle that..its an a4
#15
On The Tree
Thread Starter
iTrader: (9)
Join Date: Jul 2006
Posts: 151
Likes: 0
Received 0 Likes
on
0 Posts
..
ok, its too low...i tried to move the car and it died on me..i have a diablo sport tuner but dont see anything in the book about adjusting idle...only rev limiter...should i try the screw or what...It has now showing a ses light so i ran diagnostics.....fault 1 p0122 t/b sensor A, ciruit low input,,,fault 2 P0155 02S Heater Circuit Bank 2 Sensor 1 Malfunction,,,Fault 3 P0506 Idle Control System, RPM lower then expected....Also this t/b came with sensors on it...Should I try to put the sensors that came off of my stock t/b on to the ported one
Last edited by bow125106; 08-12-2007 at 07:03 PM.