Nitrous Oxide Installation | Tuning | Products
Sponsored by:
Sponsored by:

Manual shift no2 guys come in

Thread Tools
 
Search this Thread
 
Old 08-05-2017, 01:19 PM
  #1  
Launching!
Thread Starter
 
gmtechnician's Avatar
 
Join Date: May 2005
Location: Ada, Oklahoma
Posts: 285
Likes: 0
Received 0 Likes on 0 Posts

Default Manual shift no2 guys come in

What rpm are you activating your nitrous. I've got mine set at 3000 and it's not spraying till after the 60ft.
Old 08-06-2017, 03:19 PM
  #2  
Launching!
Thread Starter
 
gmtechnician's Avatar
 
Join Date: May 2005
Location: Ada, Oklahoma
Posts: 285
Likes: 0
Received 0 Likes on 0 Posts

Default

Ok. What rpm are any of you activating your nitrous at.
Old 08-06-2017, 07:34 PM
  #3  
9 Second Club
iTrader: (2)
 
N2RACINGLS1's's Avatar
 
Join Date: Dec 2005
Location: East, TN.
Posts: 1,194
Likes: 0
Received 2 Likes on 2 Posts

Default

Not sure how you are doing that. 3k rpm's 60 foot out doesn't seem possible. I am auto stalled and leave roughly at that rpm and at WOT nitrous is 100% on with no delay. When I run a 6spd I am leaving at 2,200 and shifting into 2nd gear before the 60 foot mark at 6,200 rpm's.

N2
Old 08-09-2017, 10:00 AM
  #4  
"I MAID THEESE"
iTrader: (3)
 
Mavn's Avatar
 
Join Date: Jul 2011
Location: Houston
Posts: 2,744
Received 675 Likes on 425 Posts

Default

Originally Posted by N2RACINGLS1's
Not sure how you are doing that. 3k rpm's 60 foot out doesn't seem possible. I am auto stalled and leave roughly at that rpm and at WOT nitrous is 100% on with no delay. When I run a 6spd I am leaving at 2,200 and shifting into 2nd gear before the 60 foot mark at 6,200 rpm's.

N2
Same... Idk how ypou can 6o ft in 1 gear under 3k lol
Old 08-09-2017, 11:55 AM
  #5  
TECH Junkie
 
MaroonMonsterLS1's Avatar
 
Join Date: Dec 2012
Location: Iowa
Posts: 3,542
Received 1,218 Likes on 782 Posts

Default

Tach switch set wrong? double the RPM (6000) seems believable
Old 08-10-2017, 01:38 PM
  #6  
Launching!
Thread Starter
 
gmtechnician's Avatar
 
Join Date: May 2005
Location: Ada, Oklahoma
Posts: 285
Likes: 0
Received 0 Likes on 0 Posts

Default

I guess I should explain the situation a little better. My car is a 02 Camaro 6 speed. 3.73 gears and 26 inch (315 wide) mickey Thompson drag radials. When I launch on the street I can spin the tire a little and it really takes off hard. At the track the car gets great traction and bogs and has to pull up the rpm range. If I dump the clutch the radials don't give as much and I just go up in smoke. With the t56 first gear at 2.66 and 26 inch tire and 3.73 gears 3000 rpm is at 24 mph. At 24 mph im right at the 60 ft box. The car picked up .7 seconds with a 100 shot and 3.73s but I was hoping for a little more. Especially in the 60 ft. So back to the question has anyone sprayed under 3000 with any luck?
Old 08-10-2017, 03:21 PM
  #7  
FormerVendor
iTrader: (2)
 
brandon@nitrousoutlet's Avatar
 
Join Date: Feb 2013
Location: Waco, TX
Posts: 1,479
Received 20 Likes on 18 Posts

Default

Originally Posted by gmtechnician
I guess I should explain the situation a little better. My car is a 02 Camaro 6 speed. 3.73 gears and 26 inch (315 wide) mickey Thompson drag radials. When I launch on the street I can spin the tire a little and it really takes off hard. At the track the car gets great traction and bogs and has to pull up the rpm range. If I dump the clutch the radials don't give as much and I just go up in smoke. With the t56 first gear at 2.66 and 26 inch tire and 3.73 gears 3000 rpm is at 24 mph. At 24 mph im right at the 60 ft box. The car picked up .7 seconds with a 100 shot and 3.73s but I was hoping for a little more. Especially in the 60 ft. So back to the question has anyone sprayed under 3000 with any luck?
Whats the suspension setup on the car?
Old 08-10-2017, 03:45 PM
  #8  
Launching!
Thread Starter
 
gmtechnician's Avatar
 
Join Date: May 2005
Location: Ada, Oklahoma
Posts: 285
Likes: 0
Received 0 Likes on 0 Posts

Default

The car mainly does autocross duty but it has for now tubular k-member and lower control arms in the front and tubular lower control arms and panhard bar in the back. stock shocks and everything else
Old 08-10-2017, 06:16 PM
  #9  
TECH Apprentice
iTrader: (4)
 
CyberGrey Z28's Avatar
 
Join Date: Oct 2009
Posts: 337
Likes: 0
Received 2 Likes on 2 Posts
Default

You need to launch above 4k with a 6 speed. Get rid of those drags for the track and get a slick mt3053S(26 inch slick)


post up your time slip.
Old 08-12-2017, 04:44 PM
  #10  
9 Second Club
iTrader: (2)
 
N2RACINGLS1's's Avatar
 
Join Date: Dec 2005
Location: East, TN.
Posts: 1,194
Likes: 0
Received 2 Likes on 2 Posts

Default

OK so you are taking it easy off the line. I would not spray below 3K rpm's if the car is under load trying to build mph and rpm's it could backfire and create all kind of problems for you. Just up the shot to 125 and see how it does. Make sure you are at WOT when the nitrous comes on.

N2

Last edited by N2RACINGLS1's; 08-12-2017 at 05:40 PM.
Old 08-12-2017, 04:48 PM
  #11  
10 Second Club
iTrader: (11)
 
Zmg00camaross's Avatar
 
Join Date: Jun 2009
Location: Missouri
Posts: 5,046
Received 47 Likes on 41 Posts

Default

Better tires and launch higher. My car never sees below 5000 rpm at the track. With nitrous you could launch at 4500 and spray straight out of the hole when you release the clutch.




All times are GMT -5. The time now is 08:19 PM.