Black Series Display Controllers INSTOCK!
Black Series Display Controllers INSTOCK! Hey Huys I am starting a fresh thread just incase you over look the old one.
Ok guys we have these gauges on the shelf and ready to ship.. All Back orders have been shiped and you should start seeing some buzz about them from people using them shortly!!!
https://ls1tech.com/forums/nitrous-oxide/736609-new-products-black-series-display-controllers.html
Ok guys we have these gauges on the shelf and ready to ship.. All Back orders have been shiped and you should start seeing some buzz about them from people using them shortly!!!
https://ls1tech.com/forums/nitrous-oxide/736609-new-products-black-series-display-controllers.html
Buzzzzzzz
Hope to get some great pics and do a lil write up with mine, doing a few changes to my system
(non-progressive gauge). Having to redo my panel since the heater is controlled by the gauge 
Hopefully...
Delete AFR gauge...monitored and displayed in the Black gauge,
Remove and replace Nitrous gauge with Black gauge (Freeing up a pod)
Install in Pod, Stage Activation lights (In drivers vision, pretty useless in console) and relocate tune switch to Pod
Features added to my System
Enable AFR cutoff's
Log Nitrous Bottle Pressure w/ new sending unit
Move LC-1 cal from engine compartment to panel
Hope to get some great pics and do a lil write up with mine, doing a few changes to my system
(non-progressive gauge). Having to redo my panel since the heater is controlled by the gauge Hopefully...
Delete AFR gauge...monitored and displayed in the Black gauge,
Remove and replace Nitrous gauge with Black gauge (Freeing up a pod)
Install in Pod, Stage Activation lights (In drivers vision, pretty useless in console) and relocate tune switch to Pod
Features added to my System
Enable AFR cutoff's
Log Nitrous Bottle Pressure w/ new sending unit
Move LC-1 cal from engine compartment to panel
Hi dave
I looked for the Black Series Display Controllers on your site and did not see them. They look very cool. I there a PDF copy of the manual that we can see? Is the a OBD gage or what? Who make them? What is there site?
Thanks
I looked for the Black Series Display Controllers on your site and did not see them. They look very cool. I there a PDF copy of the manual that we can see? Is the a OBD gage or what? Who make them? What is there site?
Thanks
Closed ex-Sponsor Account
iTrader: (1)
Joined: Jul 2004
Posts: 2,797
Likes: 0
From: Wichita Falls, TX
We will get them on our site asap.
Trending Topics
In the install process now, hoping to have the Gauge Accessories working (Wideband and heater) today, gonna let Vinny set up the noid wiring for the safety's in the engine bay. Couple of hours I should have some power off pics (maybe some power on ones as well...)
Since I am going to be nw the N20 game, I would like to get the best set up possible. I am going to be getting one of the two guages, but what wideband works best with these units?
Its in, will wire and have powered up shots tommorrow.
Hooking up the LC-1 Wideband, the heater, and the nitrous sending pressure sending unit; will snap pics of the various displays when its up and running
Hooking up the LC-1 Wideband, the heater, and the nitrous sending pressure sending unit; will snap pics of the various displays when its up and running
Closed ex-Sponsor Account
iTrader: (1)
Joined: Jul 2004
Posts: 2,797
Likes: 0
From: Wichita Falls, TX
If you want progressive, then the P
Want bottle weight, then the V
Either one works with any wideband as long as it has a analog output.
Beer power that puppy up.
I am working on it! Just buttoned up the drivers side, put the wires in conduit and routed and tie wrapped them out of the way (Vinny would be proud!)...pulling the passenger side apart now to run the nitrous pressure sending unit harness back as well as the heater relay wire. Then I have to route the LC-1 wires to the cab (the second analog input as well as the cal setup I moving to the cab vice the engine compartment)...
Wife has off today so progress may be even slower
LOL good thing I am salary and not hourly! 
I am working on it! Just buttoned up the drivers side, put the wires in conduit and routed and tie wrapped them out of the way (Vinny would be proud!)...pulling the passenger side apart now to run the nitrous pressure sending unit harness back as well as the heater relay wire. Then I have to route the LC-1 wires to the cab (the second analog input as well as the cal setup I moving to the cab vice the engine compartment)...
Wife has off today so progress may be even slower LOL good thing I am salary and not hourly!
Wife has off today so progress may be even slower
LOL good thing I am salary and not hourly!
Looks nice, but I can't wait to see it lit-up!
I am at the back, trying to figure out my heater scheme...even though the gauge has the built in heater controls, the pressure gauge is on the mainline in my configuration, so I have to have the bottle open for the gauge to correctly control it...however, I think I will just connect the heater wire from the gauge to the relay, like it was from a switch (and the heater pressure switch on the bottle will work as it should). The gauge will auto shut it off after 15 minutes (with the bottle closed) because it will not see a change in pressure; if the bottle gets to pressure before the 15 minutes the bottle heater switch will shut it off. I can live with that and just be aware of it.
