Orygun guys?
02-01-2012, 02:17 AM
#7143
anyone need an upgraded valvetrain?
I have TEA .650 springs/retainers in my L92s right now. my lunati cam is .651 lift. decided to upgrade to prc .675 springs just to be safe. Also going to have the L92s CNC'd.
so Ill have my .650 springs/retainers forsale. The were only installed in the heads. Never ran. Zero run time. Been sitting in the garage.
Figured Id give the NW section 1st dibs. Sending my heads off within the week, so it will be about 2 weeks ish by the time they come back and the TEA springs are removed.
I have TEA .650 springs/retainers in my L92s right now. my lunati cam is .651 lift. decided to upgrade to prc .675 springs just to be safe. Also going to have the L92s CNC'd.
so Ill have my .650 springs/retainers forsale. The were only installed in the heads. Never ran. Zero run time. Been sitting in the garage.
Figured Id give the NW section 1st dibs. Sending my heads off within the week, so it will be about 2 weeks ish by the time they come back and the TEA springs are removed.
02-06-2012, 05:18 PM
#7145
11 Second Club
new to this area Hey guys,
not sure f this is the best place to post this, btu why not... I am new to the northwest section, but not noe to this site or any of that, even though I don't think I ahve been on here in a few years, lol...
Amyhow, I just recently moved to Oregon after quite a few life changes brought me to the west coast, from just outside Philly, PA. My car is being stored at my father-in-law's place in Washington until we get fully moved in an settled, but I was up there this weekend checking out my car and it made me mis the car and want to get back onto the forums...
not sure f this is the best place to post this, btu why not... I am new to the northwest section, but not noe to this site or any of that, even though I don't think I ahve been on here in a few years, lol...
Amyhow, I just recently moved to Oregon after quite a few life changes brought me to the west coast, from just outside Philly, PA. My car is being stored at my father-in-law's place in Washington until we get fully moved in an settled, but I was up there this weekend checking out my car and it made me mis the car and want to get back onto the forums...
02-06-2012, 05:20 PM
#7146
Hey guys,
not sure f this is the best place to post this, btu why not... I am new to the northwest section, but not noe to this site or any of that, even though I don't think I ahve been on here in a few years, lol...
Amyhow, I just recently moved to Oregon after quite a few life changes brought me to the west coast, from just outside Philly, PA. My car is being stored at my father-in-law's place in Washington until we get fully moved in an settled, but I was up there this weekend checking out my car and it made me mis the car and want to get back onto the forums...
not sure f this is the best place to post this, btu why not... I am new to the northwest section, but not noe to this site or any of that, even though I don't think I ahve been on here in a few years, lol...
Amyhow, I just recently moved to Oregon after quite a few life changes brought me to the west coast, from just outside Philly, PA. My car is being stored at my father-in-law's place in Washington until we get fully moved in an settled, but I was up there this weekend checking out my car and it made me mis the car and want to get back onto the forums...
Todd
02-06-2012, 05:31 PM
#7147
11 Second Club
I might not be cruising in the firebird, it was in the middle of getting built into a strip only car before we started having family issues and decided to move cross country, rigth now it is pretty much just a shell, with a full 10pt cage and mostly stock-ish drivetrain...
I think sometime in the near future I will be bringing it home and getting to work on it more, but I think we are still going to keep it as a drag only car...
I think sometime in the near future I will be bringing it home and getting to work on it more, but I think we are still going to keep it as a drag only car...
02-14-2012, 11:12 AM
#7155
BTW, does anyone in the Portland area have a fender roller that they would be willing to let me use? I need to roll my fenders before March so I can fit my autoX wheels/tires.
