Newly cleaned and decked LT1 HEADS!!
#1
Newly cleaned and decked LT1 HEADS!!
Category: Engine - Intake/Fuel
Price: $350
Part Fits: 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird
Location (State): IL
Item Condition: Used
Shipping Information: Item Can be Shipped
Engine: LT1/LT4
LS Engine?: Non-LS Part
I'm looking to get $350 shipped anywhere in the lower 48.
Pics below:
Last edited by am_muscl; 06-01-2011 at 11:40 PM.
#3
the heads were bolted up to the motor and ran for about 15 seconds. they sat on the motor for about 4 months before I pulled them off and the reason I'm selling them is because I just picked up a set yesterday from Sal.
The only reason they may not look "clean" is because I had the valve covers off for a while, while I pulled the springs. but other than that with a little compressed air these things look mint.
The only reason they may not look "clean" is because I had the valve covers off for a while, while I pulled the springs. but other than that with a little compressed air these things look mint.
Trending Topics
#10
I'm putting these up for sale to try and help support my build. I was originally at $350 shipped but I'm willing to take $200 shipped to anywhere in the lower 48.
I have almost $400 into the cleaning, decking, and assembly alone. I swapped the springs out and they are not installed at the moment but they will come with the heads.
I have almost $400 into the cleaning, decking, and assembly alone. I swapped the springs out and they are not installed at the moment but they will come with the heads.
#11
Teching In
Join Date: Jun 2010
Location: goldsboronorth carolina
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
on the second pic the third exh valve is that a chunk missing from the valve seat and can i get a pic of the head without the valves in if so ill take them if no dammage
#12
no there is no chunk missing by the valve, that was just a little dirty. I just took the valves out of all the heads and bubble wrapped them. Below you will see the pics, I just cleaned them up so they look better.
and the middle one where I cleaned, notice there is no chunk missing
my paypal is ballplaya87@hotmail.com
and the middle one where I cleaned, notice there is no chunk missing
my paypal is ballplaya87@hotmail.com
#15
Staging Lane
iTrader: (8)
Join Date: Apr 2005
Location: Irwin PA
Posts: 90
Likes: 0
Received 0 Likes
on
0 Posts
I'll assume new seals were installed, valve guides are good, etc. I'm looking to put these on a stock 95 Formula, just want to know if I can reuse all of my stock parts, or if i would need to buy any replacement parts.
So, a few questions:
Thanks, sorry if the questions are stupid.
So, a few questions:
- how much was milled - is it enough to raise the compression beyond pump gas capabilities?
- will stock length pushrods work?
- will stock rocker studs work?
Thanks, sorry if the questions are stupid.
#16
There are all new valve stem seals, however upon disassembly, one of them was disfigured. All the others are in perfect condition. These were just decked to make sure it was a true flat surface, no milling that would effect compression. Stock length pushrods and rocker arm studs will work just fine.
So the only replacement part you would need is 1 valve stem seal which is less than $1 and some headgaskets, stock ones will be fine.
So the only replacement part you would need is 1 valve stem seal which is less than $1 and some headgaskets, stock ones will be fine.
#19
STILL FOR SALE!! I found some Pac Beehive 1218 springs that were originally set for these heads. They come with the locks and retainers meant for the beehive springs. I will include the pushrods AND springs with the heads for $225 shipped
Really this is a stupid deal and I can't believe they are not gone already.
Really this is a stupid deal and I can't believe they are not gone already.