Wastegates, BOV, ProFlo, Injectors, DBW stuff
#1
TECH Veteran
Thread Starter
iTrader: (17)
Join Date: Mar 2009
Location: Indy
Posts: 4,220
Likes: 0
Received 0 Likes
on
0 Posts
Wastegates, BOV, ProFlo, Injectors, DBW stuff
Category: Accessories
Price: $123465
Part Fits: 2010+ Camaro, 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird, Corvette, 04-06 Pontiac GTO, 04+ Cadillac CTS-V, 67-92 Chevrolet Camaro, 67-92 Pontiac Firebird
Location (State): IN
Item Condition: Used
Engine: LS1/LS6
LS Engine?: Fits LS Engine
**Edlebrock ProFlo xt for LS1- 400 shipped lower 48
**JGS 40mm vband gates- 220 shipped each with fire ring and vband clamp lower 48
**jgs 60mm BOV 185 shipped lower 48
** GM DBW Pedal, vette- 75 shipped lower 48
** GM LS3 gold blade DBW TB- 125 shipped lower 48
** Holley 120lb injectors, will have cleaned and flowed and shipped from Eric Derr- 400 shipped lower 48
**I also have the HOlley DBW Pedal and tb harness as well if anyone wants that with the pedal and TB. Will do a package deal. Price can be discussed.
All prices do NOT include paypal which will need to be added. If you'd rather send as a gift to bypass thats fine too. My trader rating speaks for itself.
All items are ready to be shipped As soon as payments are confirmed and a valid shipping address is received. I will not ship unless the item can be signed for. All shipments are insured for the full value of the item and will require a direct signature. Just getting that out of the way now.
Thanks all. Items are a touch dusty, have been sitting in the garage untouched since Late November when they were removed from the RX7.
#5
TECH Veteran
Thread Starter
iTrader: (17)
Join Date: Mar 2009
Location: Indy
Posts: 4,220
Likes: 0
Received 0 Likes
on
0 Posts
i used copper silicone. and the TB plate on the intake as a bunch of holes, 4 of which are offset and over lapping, all threaded, i hated this, so i took the same size hole, drill bit and just cleared the threads out so i could use a bolt and nut rather then threading into the "half" holes that it comes with. Not much thread engagment that way. Nut to be clear, it comes with quite a few mounting locations. I did not drill "NEW" holes. just opened up what was there.
thank you for bringing that up, been awhile i forgot.
thank you for bringing that up, been awhile i forgot.
#6
TECH Fanatic
iTrader: (42)
i used copper silicone. and the TB plate on the intake as a bunch of holes, 4 of which are offset and over lapping, all threaded, i hated this, so i took the same size hole, drill bit and just cleared the threads out so i could use a bolt and nut rather then threading into the "half" holes that it comes with. Not much thread engagment that way. Nut to be clear, it comes with quite a few mounting locations. I did not drill "NEW" holes. just opened up what was there.
thank you for bringing that up, been awhile i forgot.
thank you for bringing that up, been awhile i forgot.
So everything will line up with a ls2 TB, just need copper silicone?
#7
TECH Veteran
Thread Starter
iTrader: (17)
Join Date: Mar 2009
Location: Indy
Posts: 4,220
Likes: 0
Received 0 Likes
on
0 Posts
As far as i know, they bolt in place of each other. Yes, i used Silicone RTV, the orange stuff, works amazing. Rails are separate from Edlebrock and i dont have any either.