H/c LS1 Iroc with billet 78/75 VS turbo and 8.8 build
#1
H/c LS1 Iroc with billet 78/75 VS turbo and 8.8 build
Hey guys, doing ANOTHER swap, up to about 5-6 now. After the recent results of my dads nova, 11's in a 3409# car in 4800 d/a, got me a little more excited to finish this swap. Car is going to be full weight full interior with a/c.
85iroc
04 ls1
Custom grind fti cam 223/227 on a 111
Arp bolts and new oil pump
Ls7 lifters
Ported/milled/5 angle valve job 243's
Built to snot 60e with pt4000 yank
4th gen 3:42 posi rear
Racing innovations stainless headers
Home built tq arm
Lcarb
4th gen tank with factory style nylon fuel lines
96mm intake
Etc etc etc
This is my first swap I shared on here, I also have or have done a 79' z28, 80k20, two 70ss novas, and soon a 68 firebird and 97 t/a. I do my own motors, trans, harnesses, and tunes.
85iroc
04 ls1
Custom grind fti cam 223/227 on a 111
Arp bolts and new oil pump
Ls7 lifters
Ported/milled/5 angle valve job 243's
Built to snot 60e with pt4000 yank
4th gen 3:42 posi rear
Racing innovations stainless headers
Home built tq arm
Lcarb
4th gen tank with factory style nylon fuel lines
96mm intake
Etc etc etc
This is my first swap I shared on here, I also have or have done a 79' z28, 80k20, two 70ss novas, and soon a 68 firebird and 97 t/a. I do my own motors, trans, harnesses, and tunes.
Last edited by Cwarta; 04-20-2017 at 11:11 PM.
#4
I like it, just because no one replied doesn't mean we aren't reading.
Is that a pp intake? Any reason to go that over an ls6?
What did you use to mount the drive train?
What about exhaust details?
Is that a pp intake? Any reason to go that over an ls6?
What did you use to mount the drive train?
What about exhaust details?
#5
On The Tree
iTrader: (4)
Hey man what motor mounts did you use? Do you think your headers would work with the stock clamshell mounts with Hawks' mount pedestals? I've been looking for headers because it's really the only thing I need to get my motor fired but I don't wanna spend the $700 on Hawks' headers. Great built man I've been workin on mine for about 2 years haha
#6
Thanks guys!
I've got the Pp intake because I picked it up for $109 brand new in the box locally. I've done a ton of reading on it, and the people who have bought it like it, and I've seen back to back dyno results of a 9rwhp gain over the ls6 intake, more than once. Either way, it looks better than the truck I intake haha.
I built the tq arm it is tunnel mounted, not finished yet. Car runs but I'm working on some issues. Custom mad trans crossmember.
Exhaust is up in the air still, either 4" single or dual 3"
Motor mounts are actually trans adapt s10 kit I got used locally, fit great and work great. Headers are 1 3/4 racing innovations swap headers off eBay, $350 shipped fit like a glove, drop right in with engine in the car!
I've got the Pp intake because I picked it up for $109 brand new in the box locally. I've done a ton of reading on it, and the people who have bought it like it, and I've seen back to back dyno results of a 9rwhp gain over the ls6 intake, more than once. Either way, it looks better than the truck I intake haha.
I built the tq arm it is tunnel mounted, not finished yet. Car runs but I'm working on some issues. Custom mad trans crossmember.
Exhaust is up in the air still, either 4" single or dual 3"
Motor mounts are actually trans adapt s10 kit I got used locally, fit great and work great. Headers are 1 3/4 racing innovations swap headers off eBay, $350 shipped fit like a glove, drop right in with engine in the car!
Trending Topics
#9
I'm not familiar with the Hawks pads, but from doing my reading it appears the racing innovations headers are the same ones Hawks sells or sold. They fit great and have a to. Of clearance everywhere. I think you would be fine!
Thanks for the compliments on the tq arm.
Ran into some problems tonight. I went out and got my 02 sensor wires swapped side to side because I had gotten them crisscrosses when I did my harness. Got that done, fired up the car. Tired right up then died. Tried it again and same thing. Third time nothing on the switch at all, no click no nothing. Noticed when I flip my switch forward all the interior lights dim almost dark. Checked power with a volt meter, 12.1v switch off, 7 with switch on. Out a battery charger on it and checked it, 12v+ with switch off, switch on 7v and my battery charger starts humming real loud like it's under a heavy load. I e got a serious power drain somewhere and I cannot find it. No smoke no smell no nothing.
Thanks for the compliments on the tq arm.
Ran into some problems tonight. I went out and got my 02 sensor wires swapped side to side because I had gotten them crisscrosses when I did my harness. Got that done, fired up the car. Tired right up then died. Tried it again and same thing. Third time nothing on the switch at all, no click no nothing. Noticed when I flip my switch forward all the interior lights dim almost dark. Checked power with a volt meter, 12.1v switch off, 7 with switch on. Out a battery charger on it and checked it, 12v+ with switch off, switch on 7v and my battery charger starts humming real loud like it's under a heavy load. I e got a serious power drain somewhere and I cannot find it. No smoke no smell no nothing.
#10
On The Tree
iTrader: (4)
Thanks a lot for your replies about the headers and motor mounts man I appreciate it! I'll be following your build. And for your parasitic draw, is the case of one of your o2s touching a body ground or is there an opening in any of your wires? That's odd that it only seemed to happen after you switched your o2s
#12
Turned out the brand new battery shorted out internally. Had it tested, failed instantky. Gave me a replacement and it fired right up. Now to get my idle,figured out. Can't get my hp tuners to read tps on dbc cars Fter the latest update.
#18
I actually built my own, my engine is as far back as the mounts will allow, and the header ends very close to the frame angling in no way possible to get a pipe on it with out some crazy nasty elbow right off the header. I cut my frame partially out and rebuilt it, my y pipe is very tucked up into the car now. I can take pictures if you would like. Have not had a chance to drive it yet with the new stall, I had a 3600 previously and it was veryyyy street friendly.. I want the car to run hard, so I got this stall haha. Hope run mid 11's at least in 3500+ d/a