6-Speed Record?
#1
Thread Starter
10 Second Club
iTrader: (6)
Joined: Jan 2006
Posts: 673
Likes: 0
From: Hattiesburg, MS
6-Speed Record?
What is the stock bottom end(rod, pistons, and etc.), stock 6-speed tranny record? I am talking about nitrous, boost, anypower adder but they have to be on the stock bottom end and stock tranny.
#5
Originally Posted by PowerShift408
How old are you teenage phenom? Maybe I can challenge your for the youngest fastest title next season...
#6
Thread Starter
10 Second Club
iTrader: (6)
Joined: Jan 2006
Posts: 673
Likes: 0
From: Hattiesburg, MS
I just turned 17 years old. I ran my first 10 sec pass when I was 16. And I also had a 12 sec mustang prior to this car(I was 14 when I got it) But yea my car is stock bottom end....so if your 408 car can't outrun mine then. We are still racing in Missisissippi. What are you talking about next season? I am mainly working on suspension right now. The car has come some high 1.5 60ft's before but it cuts consistent mid to low 1.6's. My goal is to get the car in the high 1.4's so that should be worth a tenth or two. Oh and I'm still on the stock aluminum driveshaft.
Last edited by TeEnAgE pHeNoM; 11-16-2006 at 08:27 AM.
#7
Originally Posted by TeEnAgE pHeNoM
I just turned 17 years old. I ran my first 10 sec pass when I was 16. And I also had a 12 sec mustang prior to this car(I was 14 when I got it) But yea my car is stock bottom end....so if your 408 car can't outrun mine then. We are still racing in Missisissippi. What are you talking about next season? I am mainly working on suspension right now. The car has come some high 1.5 60ft's before but it cuts consistent mid to low 1.6's. My goal is to get the car in the high 1.4's so that should be worth a tenth or two. Oh and I'm still on the stock aluminum driveshaft.
Trending Topics
#9
Originally Posted by TeEnAgE pHeNoM
What is the stock bottom end(rod, pistons, and etc.), stock 6-speed tranny record? I am talking about nitrous, boost, anypower adder but they have to be on the stock bottom end and stock tranny.
#10
Thread Starter
10 Second Club
iTrader: (6)
Joined: Jan 2006
Posts: 673
Likes: 0
From: Hattiesburg, MS
Yea well I'm at 10.6x right now with the trap speed to go 10.4x and my tranny is good that I know of. I don't powershift so maybe that will extend the life of it. Why don't you just put on kit on your car Rodney? Run some 9's.
#11
Originally Posted by TeEnAgE pHeNoM
Yea well I'm at 10.6x right now with the trap speed to go 10.4x and my tranny is good that I know of. I don't powershift so maybe that will extend the life of it. Why don't you just put on kit on your car Rodney? Run some 9's.
#16
I went 12.80 on a stock 300hp 327 cam only (1967 camaro engine) using the solid lift 30/30 vette cam, dule plane intake and 780 dp holley with with a stock 4 speed with 5.14 gears! Right after my first pair of M/T et streets. I was happy with those times for an old factory setup. The gears required to launch that muncie without torque were a bit radical for the highway.
You guys got me beat though on both age and funding.
Have all that fun for me too. Faster, faster, must go faster
Henry
You guys got me beat though on both age and funding.
Have all that fun for me too. Faster, faster, must go faster
Henry
#18
Thread Starter
10 Second Club
iTrader: (6)
Joined: Jan 2006
Posts: 673
Likes: 0
From: Hattiesburg, MS
Originally Posted by camscam02
ill be have you beat for youngest N/a! lol just turned 17 a couple weeks ago! no spary for me right now! here in the next month im looking to go 10's cam only!
My raceweight is the same as yours and you have a slightly bigger cam though. Not to mention that you have an automatic! Nice times though man! I wish I could get some of that negative DA! I hope to hit some 11.50'
s on motor when I take it to the track when it warms up!
#20
Originally Posted by camscam02
lol yup its all about the auto and a big stall! lol and ya the raceweight is the same!( that sucks!) do you Daily drive your car?
9.8 138-140 on motor 3100lbs (will be over 3200 once i get the cage installed so i can make more than one pass)