Ap-Engineering 347 cheap street short block
#1
PSJ Wannabe & Attention Whore
Thread Starter
iTrader: (-10)
Join Date: Jan 2004
Posts: 531
Likes: 0
Received 0 Likes
on
0 Posts
Ap-Engineering 347 cheap street short block
Ap-engineering
Cheap Street 347 Cubic Inch Ls6 Shortblock
$2,799.00 W/cores
· Polished & Magnafluxed Stock Crank
· Diamond Forged Pistons / Flat Tops Or Dish
· Diamond 4130 Chromemoly Wrist Pins
· Diamond Proselect Ring Set / File Fit
· Eagle H Beam Connecting Rods
· Federal Mogul 152m Main Bearings
· Clevite Cb663h Connecting Rod Bearings
· Arp Main Studs
· Blueprinted & Fully Balanced
· Assembled
Options
· Camshafts - $399.00
· Ported & Prepped Oil Pumps - $120.00
· INSTALL FRONT, REAR COVER & OIL PAN - N/C
(CUSTOMER MUST BUY GASKETS OR SEND THEM TO US)
· ARP HEAD STUDS - $219.00
****CORE CHARGES (BLOCK & CRANK) - $700.00****
Im here Monday through Friday 9 am until 5 pm to aswer any of your questions.
Cheap Street 347 Cubic Inch Ls6 Shortblock
$2,799.00 W/cores
· Polished & Magnafluxed Stock Crank
· Diamond Forged Pistons / Flat Tops Or Dish
· Diamond 4130 Chromemoly Wrist Pins
· Diamond Proselect Ring Set / File Fit
· Eagle H Beam Connecting Rods
· Federal Mogul 152m Main Bearings
· Clevite Cb663h Connecting Rod Bearings
· Arp Main Studs
· Blueprinted & Fully Balanced
· Assembled
Options
· Camshafts - $399.00
· Ported & Prepped Oil Pumps - $120.00
· INSTALL FRONT, REAR COVER & OIL PAN - N/C
(CUSTOMER MUST BUY GASKETS OR SEND THEM TO US)
· ARP HEAD STUDS - $219.00
****CORE CHARGES (BLOCK & CRANK) - $700.00****
Im here Monday through Friday 9 am until 5 pm to aswer any of your questions.
Last edited by BOO HOO BRIAN; 01-23-2004 at 04:15 PM.
#7
TECH Fanatic
iTrader: (8)
Join Date: Aug 2003
Location: Germany
Posts: 1,145
Likes: 0
Received 0 Likes
on
0 Posts
I just wanted to post that i am in the process of building an engine through AP Engineering. I have had all of my questions and concerns answered fast and friendly. They gave me many options from budget to high dollar and have been extremely Helpful. I have received a few PM's from people in Michigan refering me to them even after i decided to go with them. Thanks APE, i look forward to our buildup.
Scoobs
Scoobs
Trending Topics
#9
TECH Junkie
Join Date: Dec 2001
Location: Lakeland, FL
Posts: 3,242
Likes: 0
Received 0 Likes
on
0 Posts
I'll second what scoobs said. I am also having a bottom end built by APE and Chris has been more than helpful and answers my pm's/emails and phone calls quicker than any sponsor I have done business with before. Thanks alot Chris !
#11
Launching!
Join Date: Sep 2002
Location: Clinton Twp. Mi
Posts: 297
Likes: 0
Received 0 Likes
on
0 Posts
Thanks guy's just trying to help and bring a better product to the market! If you remember when I brought Diamond Pistons to this board no buddy had really heard of them and the LS1 market was not being taken care of by the other pistons manufactures. Now how many people on this board have heard of Diamond pistons? Also how many people are running them? It's a pretty big amount and they carry a lot of shelf pistons to help lower the cost so you don't have to buy customs. Well that is the same thing I am trying to do now with my company. Give you guy's a good quality product and make it affordable. I am open to any suggestion you guy's may have that will help me bring this a long.
Thanks again.
Thanks again.
#12
On The Tree
Join Date: Oct 2002
Location: Slow....in Tampa
Posts: 198
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by AP-Engineering
Thanks guy's just trying to help and bring a better product to the market! If you remember when I brought Diamond Pistons to this board no buddy had really heard of them and the LS1 market was not being taken care of by the other pistons manufactures. Now how many people on this board have heard of Diamond pistons? Also how many people are running them? It's a pretty big amount and they carry a lot of shelf pistons to help lower the cost so you don't have to buy customs. Well that is the same thing I am trying to do now with my company. Give you guy's a good quality product and make it affordable. I am open to any suggestion you guy's may have that will help me bring this a long.
Thanks again.
Thanks again.
WOW! Its too bad all vendors aren't like this! Better product and cheaper cost to the consumer? Can't beat that!
#13
TECH Junkie
iTrader: (1)
Well, I will take a moment to give some props again. Chris was extremely helpful at diamond and I may have been the 1st one to order a 409 Stroker as he took APE over..in fact, odered 2 409s from them in the past month. After dealing w. Chris and the crew over the phone, its hard for others to meet your expectations. Fair prices , good service and I'm betting on an excellent build to boot! Thanks again to Chris and Brian for answering the damn phone and always getting back during such a busy expansion.
jason
jason
#14
Under criminal investigation for fraud
iTrader: (-2)
Join Date: Jan 2004
Posts: 1,350
Likes: 0
Received 0 Likes
on
0 Posts
Jammer, no problem that is what we are here for. You were the first to order the short blocks. Let John know that I spoke with Eagle today and cranks are on the way. Should be here before the end of the week. Also your Callies is going to ship out on Thursday. So we should have both cranks no later than next Monday. On John's engine that is all we are waiting for. Thanks for the props.
Thanks
Thanks
#18
TECH Fanatic
iTrader: (8)
Join Date: Aug 2003
Location: Germany
Posts: 1,145
Likes: 0
Received 0 Likes
on
0 Posts
Hey Mike, Mine will probably be finished last. Jay is doing the Heads now. I also sent him my LS6 intake and ordered on of his 80mm TB's. When its all said and done he will ship it to AP-E, most likely around the middle of this month. I have a good friend who lives in michigan with a WS6. He is coming down the first week of March. His cousin whom i know is driving my car back up to michigan on the return trip where AP-E will begin the tear down/ install / tune. Im also replacing the Ypipe, catback, fuel system and adding a 12 bolt. Its going to be a who new car. Those JPR heads should shine. You have the HVLD design ones?
#19
Staging Lane
Join Date: Aug 2002
Location: Jackson, MI
Posts: 77
Likes: 0
Received 0 Likes
on
0 Posts
I believe AP Engineering is going to have a great year this year with some very satisfied customers. After meeting with Chris, Brian and the rest of the crew at their shop and seeing the attitude and approach to business, I would be surprised if my prediction doesn't come to fruition (spelling?).
#20
TECH Regular
Join Date: Jul 2002
Location: Essexville,MI
Posts: 403
Likes: 0
Received 0 Likes
on
0 Posts
Well it seems they are definantly going in a 110% opposite direction than the former owners were. And they already have some wicked cars in the stables, just no one knows of them quite yet. I hope to be one of them after they tie up about 398,756 loose ends that were left on my car and get it on the dyno to tune the new motor/blower/trans combo.
Kudos on starting to get some pub to the shop, and actually being there to help.
Andy
PS Chris did you get my PM about a buddy I have that wants to get a qoute from you on a motor buildup for NOS? If not let me know.
Kudos on starting to get some pub to the shop, and actually being there to help.
Andy
PS Chris did you get my PM about a buddy I have that wants to get a qoute from you on a motor buildup for NOS? If not let me know.