How to ruin a musting meet
08-30-2010, 08:50 AM
#1
Teching In
Thread Starter
iTrader: (1)
Join Date: Feb 2009
Location: Kingwood, TX
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
How to ruin a musting meet So this oast saturday I knew some buddies with there rusty stangs and followed them up to there stan meet. there was about 10 of them from GT's GTCS, a GT500 and a new 2011 GT500. I have know most of these guys for a while so I got some runs in with a few bolt on GT's. usual just skating away from them...
Then a GT with MT/ET's out back and skinnies up from pulls in and sounds pretty good, has a decent cam lope, and is primered out.
So I go converse with him I ask him to run. he says he a built 4.6, spray the whole 9 yards. so he goes gets gas comes back and the rest was history.
http://www.youtube.com/watch?v=_e8wt8la5To
Wne from a 20 roll. he wanted the punch so I went off his jump
Cool guy, nice car and fun run. just what a saturday night needs
Then a GT with MT/ET's out back and skinnies up from pulls in and sounds pretty good, has a decent cam lope, and is primered out.
So I go converse with him I ask him to run. he says he a built 4.6, spray the whole 9 yards. so he goes gets gas comes back and the rest was history.
http://www.youtube.com/watch?v=_e8wt8la5To
Wne from a 20 roll. he wanted the punch so I went off his jump
Cool guy, nice car and fun run. just what a saturday night needs
. Good kill though. What are you mods? Was he spraying a baby shot? 
08-30-2010, 12:24 PM
#7
TECH Apprentice
iTrader: (20)
Join Date: Jul 2009
Location: Liberal land
Posts: 390
Likes: 0
Received 0 Likes
on
0 Posts
Can't see the vid at work but if he decided to try to build a 4.6 2 valver, he made a terrible choice. Your buddies must have some slow-azz stangs if none of them can keep up with a bolt on TA lol. A few of my freinds mustangs will shat on some of the quickest street cars around here.
Sweet kill none the less and I'll def check out the vid when I get home.
Sweet kill none the less and I'll def check out the vid when I get home.
Trending Topics
08-30-2010, 05:04 PM
#12
Staging Lane
Scary thing is, the guy is using spell check. I've got a coworker whose grammar is as bad as bennetts and relies religiously on spell checker. Except that his *(and OP's) grammar skills are so far gone that even that leaves open the door to obvious mistakes.
OP: nice kills btw!
OP: nice kills btw!
08-30-2010, 07:08 PM
#14
Teching In
Join Date: Aug 2008
Location: South East USA
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
Nice kill... but I don't know about his "built" 4.6, 
... You have to be dumb to invest $ in that 2V engine, might as well, sell it and get a Cobra, which presumeably still gets it's azz handed to him based on the stories here...
... You have to be dumb to invest $ in that 2V engine, might as well, sell it and get a Cobra, which presumeably still gets it's azz handed to him based on the stories here...
08-30-2010, 07:40 PM
#15
Teching In
Thread Starter
iTrader: (1)
Join Date: Feb 2009
Location: Kingwood, TX
Posts: 39
Likes: 0
Received 0 Likes
on
0 Posts
Okay okay, I wrote this in the early morning with a fussy new born in my lap. So give a guy a break!
When I asked him to run he did not mention any mods except spray. I did hear a pretty nasty lope at idle and I am sure it was not a "missfire". But someone there asked him earlier and he mentioned it was a built 2v. Beats me but who knows whats going on with it. And he was running slicks and skinnies....
As for my car Mod list is
Lid
PP throttle body
Pacestter LT's
Lethal Performance true duals
Built t56
3.73 gears out back
And fully gutted
When I asked him to run he did not mention any mods except spray. I did hear a pretty nasty lope at idle and I am sure it was not a "missfire". But someone there asked him earlier and he mentioned it was a built 2v. Beats me but who knows whats going on with it. And he was running slicks and skinnies....
As for my car Mod list is
Lid
PP throttle body
Pacestter LT's
Lethal Performance true duals
Built t56
3.73 gears out back
And fully gutted
08-30-2010, 09:56 PM
#16
Registered User
Join Date: Aug 2010
Posts: 0
Likes: 0
Received 0 Likes
on
0 Posts
lol! lame! maybe im lost but dont a ls1 have a 2v engine? lmao stupied people! hatin on the 4.6... but looks to me he was door to door with ya till 4 of your gears! that puts ya at what 100mph? so 1/8 mile he would have got ya! im just sayin! and a little birdie tells me if u bring some change he will go it again! 
08-30-2010, 10:49 PM
#17
lol! lame! maybe im lost but dont a ls1 have a 2v engine? lmao stupied people! hatin on the 4.6... but looks to me he was door to door with ya till 4 of your gears! that puts ya at what 100mph? so 1/8 mile he would have got ya! im just sayin! and a little birdie tells me if u bring some change he will go it again!
A fully built, big cammed, sprayed 4.6 on slicks and skinnies kept up with a mild bolt-on LS for the first 8th mile.
Very impressive.
08-30-2010, 11:03 PM
#19
TECH Apprentice
iTrader: (20)
Join Date: Jul 2009
Location: Liberal land
Posts: 390
Likes: 0
Received 0 Likes
on
0 Posts
lol! lame! maybe im lost but dont a ls1 have a 2v engine? lmao stupied people! hatin on the 4.6... but looks to me he was door to door with ya till 4 of your gears! that puts ya at what 100mph? so 1/8 mile he would have got ya! im just sayin! and a little birdie tells me if u bring some change he will go it again!
4.6 2V < LSx 2V
By the way, you spelled stupied wrong for all of us stupied people.
