RCSB 283 s-10 vs. 03 mach1 5spd (orange)
#1
RCSB 283 s-10 vs. 03 mach1 5spd (orange)
I was at the store getting some gas....as i was driving out of the parking lot, the mach flew by...hehe so i then proceded to chase him down....when i got next to him we had a stop coming up...At the light i revved and he revved back...and it was on like donkey kong.
I launched at about 3300, i was on the et streets.... they werent warm but they hooked good nevertheless. I slipped a lil, but gripped well enough to stay at his door out of the whole. As i wound first gear past 5 grand i started to gain a lil and all the way up to about 7200, i slammed 2nd and continued to creep up side side by side. Letting 2nd wind out got me a nose....as i threw third i began to pass him up...at the end of third he was just about at my bumper. when we shut it off...
we talked at the next light ...alls he had was cai, flowmasters w/cats
walked his ***....without the dual overhead cams too...hehe lol i know his motor has way more potential....mine just currently built better.
I launched at about 3300, i was on the et streets.... they werent warm but they hooked good nevertheless. I slipped a lil, but gripped well enough to stay at his door out of the whole. As i wound first gear past 5 grand i started to gain a lil and all the way up to about 7200, i slammed 2nd and continued to creep up side side by side. Letting 2nd wind out got me a nose....as i threw third i began to pass him up...at the end of third he was just about at my bumper. when we shut it off...
we talked at the next light ...alls he had was cai, flowmasters w/cats
walked his ***....without the dual overhead cams too...hehe lol i know his motor has way more potential....mine just currently built better.
#2
Nice kill...especially in your S10....kind of curious on the details of it. I ahve seen one with a 383 in it...it was one bad ****.
BTW - <1 car length is HARDLy 'walking his ***'.
BTW - <1 car length is HARDLy 'walking his ***'.
#4
283 bored .040
k&n 14x4 with X-stream lid
Crane blueprint cam of the L-79 327/350hp .447 lift [hydraulic lift,not roller]
Vortecs off a 98 5.0/305ci.heads are slightly ported&milled[no roller rockers]
Valve sizes are 1.89/1.50, the biggest a 283 left the fac. was 1.72 int. valve
Edelbrock Vortec Performer-RPM air-gap
650 Speed Demon
Hedman long tubes, into a custom 2.5in. x-pipe fed into 2.5 40series Flows
4 speed T-10, 3:42's; 26in mickey thompson Et Streets
this motor yields about a 10:1-10.25:1 comp. ratio
at the track launching the truck @ 3000-3300rpm range i knocked off 13.5's shifting @ about 7300rpm
Thats his setup I copied from the small block section. There was a small debate about its ability and reason behind it.
Good race. With et streets it sounds legit.
k&n 14x4 with X-stream lid
Crane blueprint cam of the L-79 327/350hp .447 lift [hydraulic lift,not roller]
Vortecs off a 98 5.0/305ci.heads are slightly ported&milled[no roller rockers]
Valve sizes are 1.89/1.50, the biggest a 283 left the fac. was 1.72 int. valve
Edelbrock Vortec Performer-RPM air-gap
650 Speed Demon
Hedman long tubes, into a custom 2.5in. x-pipe fed into 2.5 40series Flows
4 speed T-10, 3:42's; 26in mickey thompson Et Streets
this motor yields about a 10:1-10.25:1 comp. ratio
at the track launching the truck @ 3000-3300rpm range i knocked off 13.5's shifting @ about 7300rpm
Thats his setup I copied from the small block section. There was a small debate about its ability and reason behind it.
Good race. With et streets it sounds legit.
#5
lol...i know....but wudeva i win! btw... ive been tuning on it and i bumped the timing to 33degrees total...it was at 30 when i managed the 13.5's.... but its loving this extra timing 13.39-13.49 isnt out of the picture.....i messed up by not goin rolller on a motor that loves to revv....ive already got a nice setup picked out ...coming sooon!!!
Trending Topics
#8
Yup i guessed the year...i guess it was an 04' ... since i thought they only came out in 03' ...LOL goes to show im not a ford guy... besides if i woulda been in the LS1 would'nve even been a race.
#9
Originally Posted by ZL1camaro
Yup i guessed the year...i guess it was an 04' ... since i thought they only came out in 03' ...LOL goes to show im not a ford guy... besides if i woulda been in the LS1 would'nve even been a race.
Nice truck.......and the bolded above......um, ok.
What's with all the stang hatin' lately?
#15
Originally Posted by Irunelevens
Based on a few of his previous posts that I've seen, that could very well be the former...
#16
Originally Posted by ZL1camaro
call me ignorant. i call it correct.... it was a joke bro... peace im outi
I was serious......I wasn't sure......no smilie...so I asked.