fixes for lean in front?
#1
On The Tree
Thread Starter
iTrader: (2)
Join Date: Oct 2011
Location: Abilene, TX
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Ok well I got my ls1 prokit with kybs installed and I have got the common lean going now. The driver front sits about 1 inch higher than passenger front. I've read countless threads but want to know what you have done to correct this lean. Doesn't have to be exact bit a whole inch seems excessive to me. Thanks for any help guys.
#3
On The Tree
Thread Starter
iTrader: (2)
Join Date: Oct 2011
Location: Abilene, TX
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Lol no I didn't mean to do it. Don't know to do it on purpose anyways. I guess ill have to have someone check it while I'm sitting in it. But seriously I'm no light weight at 250 lbs but don't think that's enough to drop another inch or am I wrong?
Morning bump for tips
Morning bump for tips
#5
On The Tree
Thread Starter
iTrader: (2)
Join Date: Oct 2011
Location: Abilene, TX
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Ok ill double check the end links. I did install new ones at time on shock install with springs. Any tips as far as how tight it should be and proper install procedure?
Well end links are nice and tight evenly on both sides. Anymore ideas from anyone? It is driving me crazy. I know I am probably going to have some lean nomatter what I do but it seems a little much. I double checked the driver front and made sure the spring is sitting properly in the seat and mount. No clue what to look for next
Well end links are nice and tight evenly on both sides. Anymore ideas from anyone? It is driving me crazy. I know I am probably going to have some lean nomatter what I do but it seems a little much. I double checked the driver front and made sure the spring is sitting properly in the seat and mount. No clue what to look for next
#7
On The Tree
Thread Starter
iTrader: (2)
Join Date: Oct 2011
Location: Abilene, TX
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Have not had the car aligned yet. The rear sits just as low as the passenger front with the hose mod.
Alright bumping it. I have had the car alligned to specs recommended on this site. Prior I had taken the driver wheel off to make sure the spring was sitting correctly in its perch. All looks good to me. Drove the car out of town this past week to make sure it settled and its still one inch higher than the passenger front. All other corners are even except this one. Could really use some tips on what needs to be done if anything can be. Thanks guys
Alright bumping it. I have had the car alligned to specs recommended on this site. Prior I had taken the driver wheel off to make sure the spring was sitting correctly in its perch. All looks good to me. Drove the car out of town this past week to make sure it settled and its still one inch higher than the passenger front. All other corners are even except this one. Could really use some tips on what needs to be done if anything can be. Thanks guys
Trending Topics
#9
On The Tree
Thread Starter
iTrader: (2)
Join Date: Oct 2011
Location: Abilene, TX
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Yea so I have read bud. This Friday I'm going to remove end links again and double check the pigtails on springs in the rear since I heard it can affect the front height somewhat and go from there. Do you think a combination of errors there could maybe tweak it a little closer than an inch or is it just high hopes?
Also to note I measured my driver front which is 26 3/4 and then my friends 2000 ta which is all factory and his is 27 1/2. I know all cars are different but 3/4 of an inch drop does not seem right after my install
Also to note I measured my driver front which is 26 3/4 and then my friends 2000 ta which is all factory and his is 27 1/2. I know all cars are different but 3/4 of an inch drop does not seem right after my install
#10
TECH Senior Member
iTrader: (35)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
So you're double sure this was checked on a flat and level surface?
Okay, so does the car level out if you disconnect the front sway bar end-links?
Are the Sway bar mounts/bushings, worn, loose, broken, damaged in anyway?
If the answer is yes to the first two, and no to the last, and the end-links were adjust the same and neither damaged in any way it's possible the bar is bent.
This would cause the link end mount locations of the sway bar (from L to R) to be at two different heights. This could be from damage or from a bar being manufactured out of spec.
FYI, this is what I went through years ago and found out the bar was manufactured out of spec.
Okay, so does the car level out if you disconnect the front sway bar end-links?
Are the Sway bar mounts/bushings, worn, loose, broken, damaged in anyway?
If the answer is yes to the first two, and no to the last, and the end-links were adjust the same and neither damaged in any way it's possible the bar is bent.
This would cause the link end mount locations of the sway bar (from L to R) to be at two different heights. This could be from damage or from a bar being manufactured out of spec.
FYI, this is what I went through years ago and found out the bar was manufactured out of spec.
#11
On The Tree
Thread Starter
iTrader: (2)
Join Date: Oct 2011
Location: Abilene, TX
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Thanks for the reply blue. Ill check everything next day off according to your post and get back to you. Btw what is the proper way to install and tighten down end links? According to how you fixed your problem
#14
Banned
iTrader: (12)
Join Date: Sep 2011
Location: Wisconsin
Posts: 223
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I can't blame the Eibach's for sure, but many guys have had trouble with them being crappy.. especially the sagging rears. You might want to try a different set of springs at least on the front just to see if the Eibach's are causing the problem. I know it's a lot of work, but if it bothers you that much I would do it.
My car is done with Bilsteins and BMR lowering springs, sits level on all 4 corners. IMO the best springs out there are Strano's and BMR's. Almost identical to each other.
My car is done with Bilsteins and BMR lowering springs, sits level on all 4 corners. IMO the best springs out there are Strano's and BMR's. Almost identical to each other.
#15
On The Tree
Thread Starter
iTrader: (2)
Join Date: Oct 2011
Location: Abilene, TX
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
So update. I removed the front end links while at work, gotta love working in a lube center with lower bays, and there is barely a 1/4 inch difference now. So does that point more towards bent sway bar or bad end links?
So correction. Drove home with swaybar disconnected and measured again. It is a little over 1/2 inch higher than passenger front which is still much better than 1 inch. Will it hurt anything driving without swaybar connected until I buy some new endlinks and get some time off? Do yall think adjusting the rear a little higher without hose mod will indirectly settle the driver front down or did I hear wrong from a post?
So correction. Drove home with swaybar disconnected and measured again. It is a little over 1/2 inch higher than passenger front which is still much better than 1 inch. Will it hurt anything driving without swaybar connected until I buy some new endlinks and get some time off? Do yall think adjusting the rear a little higher without hose mod will indirectly settle the driver front down or did I hear wrong from a post?
#16
Banned
iTrader: (12)
Join Date: Sep 2011
Location: Wisconsin
Posts: 223
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Nothing bad will happen from driving without a front swaybar, I have been for the past year. Your car will pull with the angle of the road and on bumps more, so be a little more careful. But you should be good.
#18
On The Tree
Thread Starter
iTrader: (2)
Join Date: Oct 2011
Location: Abilene, TX
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Well problem is still ongoing. Since I removed the end links the driver side settled down aboit 1/4 inch. Still a little less than 3/4 inch higher than passenger side. I'm unsure of the problem now. I know its frowned upon but I'm thinking of cutting 1/4 coil off the driver front to settle it down close to even. Any thoughts on that fellas?