rear control arms?
#4
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
You're probably thinking of founder's LCAs with the three piece poly ball bushings.
https://www.foundersperformance.com/...v=7516fd43adaa
https://www.foundersperformance.com/...v=7516fd43adaa
The bushings have to be pressed into the arms. The install of the arms to the car was fairly tough. The old ones fell right out but I had press press the new Founders into the brackets with a scissor jack.
Last edited by Y2K_Frenzy; 05-23-2022 at 06:36 AM.
#5
TECH Senior Member
iTrader: (4)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Founder-s-swivel-joint-vs-umi-roto-joint
Talking with Sam Strano before buying any parts may be worthwhile. Sam is a master at suggesting best matched set up for the best price possible.
An adjustable LCA's allows dialing every thing in better when alignment is done.
Talking with Sam Strano before buying any parts may be worthwhile. Sam is a master at suggesting best matched set up for the best price possible.
An adjustable LCA's allows dialing every thing in better when alignment is done.
#6
TECH Fanatic
iTrader: (5)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
J&M also makes one/sells one (prob the same exact one) with three piece but it’s a little more expensive. I’ve had the J&M for a good while now on a Mustang and I put the Founders brand on my Camaro not long ago. Both have been good. J&M
The bushings have to be pressed into the arms. The install of the arms to the car was fairly tough. The old ones fell right out but I had press press the new Founders into the brackets with a scissor jack.
The bushings have to be pressed into the arms. The install of the arms to the car was fairly tough. The old ones fell right out but I had press press the new Founders into the brackets with a scissor jack.
#7
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
That makes me wonder how effective the ball and socket is in that design. Rod ends, johnny joints and similar joints like UMI's Roto-joint and Sphon's Del-Sphere, all have air gaps between the mounting ears of the clevis/torque box, and the body of the joint so it car articulate. Rubber accomplishes this by being squishy. If the face of the poly bushing cup, that holds the ball, is flush and very tight against the mounting surface, what do you get out of the pivot ball?
The Testing:
We built a fixture which simulated a factory control arm mounting and tested how much force was needed to make the control arm articulate (twist) in those mounts and the results where astounding.Poly-Joint Bushings:
- 5 degrees of total rotation = 26.1 foot/pounds of torque
- 7.5 degrees of total rotation = 35.8 foot/pounds of torque
- 10 degrees of total rotation = 41.7 foot/pounds of torque
- 5 degrees of total rotation = 124.7 foot/pounds of torque
- 7.5 degrees of total rotation = 156.4 foot/pounds of torque
- 10 degrees of total rotation = not measurable with fixture. The 1/2″ grade 8 bolt twisted in half at 9.2 degrees which was 210 foot/pounds of torque.
![](https://cimg8.ibsrv.net/gimg/ls1tech.com-vbulletin/1500x2000/520de8d4_538b_4de0_9178_d57623bf2e24_f8017e9ac31ec171ac68497d014475b01511b374.jpeg)
![](https://cimg0.ibsrv.net/gimg/ls1tech.com-vbulletin/1500x2000/8ab67abf_9fde_4233_b01e_76f1b270f988_343003d9acd5aa02d0684b9fedd9d34b6c0badf6.jpeg)
https://www.foundersperformance.com/...v=7516fd43adaa
*Edit* The cups that the ***** go in are a soft rubber. You can compress them by hand.
Last edited by Y2K_Frenzy; 05-23-2022 at 09:03 AM.
Trending Topics
The following users liked this post:
Y2K_Frenzy (05-23-2022)
#9
The following users liked this post:
wannafbody (05-25-2022)
#11
#13
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Ok. Got these in and they are really nice looking pieces. The center ball looks to be made of delrin with soft poly outers. First bit of advice, buy the bolts as the new bolts are slightly shorter and have locknuts with them. I found that using screwdrivers as prybars helped a lot. On the axle side, putting the bolt in from the inside was easier.
I took the car for a drive down a not so smooth road with some washboard sections. The ride is firm but not harsh. I didn't notice any wheel hop. Hope this helps someone.
I took the car for a drive down a not so smooth road with some washboard sections. The ride is firm but not harsh. I didn't notice any wheel hop. Hope this helps someone.
Last edited by wannafbody; 05-26-2022 at 07:01 PM.
The following users liked this post:
Y2K_Frenzy (05-26-2022)
#14
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Ok. Got these in and they are really nice looking pieces. The center ball looks to be made of delrin with soft poly outers. First bit of advice, buy the bolts as the new bolts are slightly shorter and have locknuts with them. I found that using screwdrivers as prybars helped a lot. On the axle side, putting the bolt in from the inside was easier.
I took the car for a drive down a not so smooth road with some washboard sections. The ride is firm but not harsh. I didn't notice any wheel hop. Hope this helps someone.
I took the car for a drive down a not so smooth road with some washboard sections. The ride is firm but not harsh. I didn't notice any wheel hop. Hope this helps someone.
#16
TECH Fanatic
iTrader: (1)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Founder-s-swivel-joint-vs-umi-roto-joint
Talking with Sam Strano before buying any parts may be worthwhile. Sam is a master at suggesting best matched set up for the best price possible.
An adjustable LCA's allows dialing every thing in better when alignment is done.
Talking with Sam Strano before buying any parts may be worthwhile. Sam is a master at suggesting best matched set up for the best price possible.
An adjustable LCA's allows dialing every thing in better when alignment is done.
The following users liked this post:
Y2K_Frenzy (06-12-2022)