Lowering the TA... Advice Needed
Lowering the TA... Advice Needed I dont want it "slammed". I just want it somewhat lower. Seems to be that a LOT of Fbodies go w/ a Pro-Kit & arent complaining too much about it. I'm just worried about bottoming out or scraping everything. I'll eventually have long tubes, but from what iv heard, as long as i stay away from SLPs, i wont have to worry about the long tubes scraping b/c they tuck very well underneath.
a buddy told me that i should go w/ the BMR springs b/c they only drop the car an inch. So basically, im tryin to decide b/t the Pro-Kit and the BMR. Also, should I remove the rear Isolator?
I'm planning on doing this when I get the rims.. which will be 17x9.5 up front and 17x11 in the back so this too is something to take into consideration.
Here is the package deal im looking at from Thunder Racing. scroll down and you'll see it...
http://thunderracing.com/catalog/?ac...&vid=3&pcid=91
I just dont know if i should go w/ BMRs or the Pro-Kit
any suggestions or insight would be highly appreciated.
a buddy told me that i should go w/ the BMR springs b/c they only drop the car an inch. So basically, im tryin to decide b/t the Pro-Kit and the BMR. Also, should I remove the rear Isolator?
I'm planning on doing this when I get the rims.. which will be 17x9.5 up front and 17x11 in the back so this too is something to take into consideration.
Here is the package deal im looking at from Thunder Racing. scroll down and you'll see it...
http://thunderracing.com/catalog/?ac...&vid=3&pcid=91
I just dont know if i should go w/ BMRs or the Pro-Kit
any suggestions or insight would be highly appreciated.
I recently ordered that package from Thunder with the intention of getting the BMRs, but went with the Pro Kit because I was told that the BMR springs are on back-order for as long as they could tell.
I REALLY appreciate the input fellas...
Id love to see some pics if anyone cares to post any or they can PM me a link. 01 RED WS6, def. send me some pics sometime if you would. I dont think i wanna go w/ too much lower than an inch.
again, thanks guys
Id love to see some pics if anyone cares to post any or they can PM me a link. 01 RED WS6, def. send me some pics sometime if you would. I dont think i wanna go w/ too much lower than an inch.
again, thanks guys
https://ls1tech.com/forums/suspension-brakes/300651-drop-like-its-hot.html
here are the pics from the before and after
here are the pics from the before and after
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
01 Red WS6, nice pics... i cant tell much of a difference, but the car looks good. I also just saw it over on LS2. im likin the BMRs
Last edited by DANSBIRD; Apr 19, 2005 at 05:35 PM.
Well the before was taken the night before I got the springs put in and the after was the same day they were installed. They have settled a little more. Once you get them in you can tell. I wasn't expecting that much of a differance but it was a nice drop. I'll try to get some more pics this weekend and the final drop measurments to show the total drop
prokits with 18's on a slight uphill
check sig for other suspension mods
no complaints what so ever but i may change out to Ground Controls cuz i want the height adjustment to lower the front a tad
check sig for other suspension mods
no complaints what so ever but i may change out to Ground Controls cuz i want the height adjustment to lower the front a tad
