plastigage - LS1TECH - Camaro and Firebird Forum Discussion - Threads Tagged with plastigage

LS1TECH - Camaro and Firebird Forum Discussion
Tags
Threads Tagged with plastigage

Threads Tagged with plastigage

Thread / Thread Starter

Last Post

Replies

Views

Forum

0015, accurate, bearing, bearings, build, clearance, crank, eagle, engine, plastigage, rod, tight

Is .0015 measured with platigage too tight for a rod bearing clearance?

FastKat on 05-04-2014

05-08-2014 11:29 AM
by crossbreed383

Go to last post

12

19,102

Generation IV Internal Engine

accurate, bearing, bearings, builder, check, checking, clearance, crankshaft, engine, gauge, made, plasti, plastigage, plastigauge, rod

To plastigage or not to plastigage... Rod bearing replacement?

NightmareTA on 08-25-2013

08-25-2013 01:52 PM
by Cam72aro

Go to last post

8

14,983

Forced Induction

53, accuracy, accurate, crank, l33, ls1, ls1tech, main, plastigage, plastiguage

Plastigage accuracy???

showvette on 07-14-2013

07-14-2013 09:10 PM
by showvette

Go to last post

3

3,522

Generation III Internal Engine

bbc, beam, cb663h001, clearance, clevite, eagle, ls1, ls2, ls3, ls7, ls9, plastigage, pontiac, power, rod, sealed, side, tight

Rod clearance issues

Tainted on 01-05-2013

01-06-2013 09:36 PM
by Tainted

Go to last post

15

2,611

Generation IV Internal Engine

0001, 002, accuracy, bearing, bearings, clearance, clearances, feeler, gauge, ls1, ls9, main, plastigage, plastigauge, rod, standard

Plastigage Question???

Bad News22 on 05-09-2012

05-12-2012 08:25 PM
by Bad News22

Go to last post

15

21,827

Generation IV Internal Engine

beam, bearing, bearings, check, clearance, clearances, eagle, h, ls1, ls6, plastigage, rod, rods, setup, standard

rod bearing clearance with plastiguage

3rdCoastPowerSports on 03-09-2012

03-20-2012 05:24 PM
by RezinTexas

Go to last post

12

39,026

Generation III Internal Engine

001, 002, bearing, bearings, clearance, clearances, factory, ls1, ls1tech, lsx, lt1, oil, plastigage, pontiac, rod

factory new rod bearing clearance .002" book says .001-.002

chrisfrost on 11-29-2011

11-29-2011 05:32 PM
by chrisfrost

Go to last post

0

993

Generation III Internal Engine

0009, 0030, bearing, bearings, clearance, connecting, failure, lm7, ls, oil, plastagage, plastigage, reads, rod, rods

conn rod bear oil clearance quest to exp eng builder

chrisfrost on 06-14-2011

06-15-2011 09:25 PM
by A.R. Shale Targa

Go to last post

4

1,247

Generation III Internal Engine

bearings, check, clearance, clearence, crankshaft, lima, locationinstroketoplastigauge, make, measure, ohio, oil, plastigage, plastigauge, plastiguage, platigage, read

More accurate oil clearance check/ 2 pieces of plastigage

chrisfrost on 05-16-2011

05-16-2011 10:09 PM
by chrisfrost

Go to last post

2

1,759

Generation III Internal Engine

accurate, bearing, clearance, engines, gauge, inaccurate, ls1, main, mic, micrometer, plasti, plastigage, plastigauge, plastiguage, torque, versus, work

Plastigage accurate?

93 black t/a on 03-24-2009

03-18-2011 12:41 AM
by gatorhead

Go to last post

17

18,755

LT1-LT4 Modifications

accurate, ajournal, bearing, check, checks, clearance, clearances, clearences, engine, ls1, ls1tech, lsx, measure, plastigage, proper

How do you check bearing clearance the right way?

adrynalinjunkie on 01-24-2011

01-24-2011 07:07 PM
by jim ravencraft

Go to last post

3

1,261

Generation III Internal Engine

0024, 0032, builders, complaints, engine, fort, ft, hot, houston, plastigage, precision, rebuilders, rod, texas, tx, worth

ENGINE BUILDERS,, How is this possible, and what would you recommend

RARON455 on 10-05-2010

10-07-2010 11:25 PM
by KCS

Go to last post

14

1,021

Generation III Internal Engine

60, crank, crankshaft, easy, engine, hand, ls1, ls1tech, mains, plastigage, spin, stiff, tool, torque, torquing, turning

crankshaft turning torque

jrocstar on 09-18-2010

09-18-2010 05:57 PM
by SSPerformance

Go to last post

2

1,682

Generation III Internal Engine

97, clearance, ls1tech, lt1, plastigage, plastigauge

Plastigage Question

93 black t/a on 09-22-2008

09-22-2008 11:34 PM
by fergymoto

Go to last post

1

618

LT1-LT4 Modifications

Exclamation

angle, bolts, cap, gauge, homemade, lsa, main, plastigage, reuse, stock, strong, test, torque, tty, yield

stock main bolts question (pics)

(

Multi-page thread

1 2)

slowjoe99 on 08-18-2008

08-27-2008 09:09 PM
by Wilde Racing

Go to last post

26

2,586

Generation III Internal Engine

0015, 77, bbc, bearing, bearings, crank, gage, high, instructions, plastigage, plastigauge, plastiguage, reads, rod, sbc, tolerances

rod bearing plastigage help?

ezrollin on 07-19-2006

02-20-2008 10:05 PM
by m6ls1maro

Go to last post

18

13,272

Advanced Engineering Tech

assembly, bolts, ls1, main, plastigage, sealer, spec, specs, tips

LS1 assembly, advice/suggestions

69MyWay on 02-07-2005

02-14-2005 03:23 PM
by 69MyWay

Go to last post

6

773

Generation III Internal Engine

agent, bearing, constant, interpolate, ls1, ls1tech, molding, plastigage, plastigauge, plastiguage, release, removing, shells, silicone, time, works

Info on how Plastigauge is used...

Scalpel on 01-24-2004

01-24-2004 08:54 PM
by cm02WS6

Go to last post

1

1,238

Generation III Internal Engine

All times are GMT -5. The time now is 03:41 PM.