Stripped allen head bolt
#5
TECH Enthusiast
Thread Starter
iTrader: (19)
Join Date: Jun 2002
Location: San Francisco
Posts: 740
Likes: 0
Received 0 Likes
on
0 Posts
The bolt is actually not even on my car, its on the mnotorcycle im tryin' to fix. Its got a rounded head like a machine screw so vice grips are out. I was gonna try the dremel thing but that took forever last time and I just wanted to see if anyone had any other ideas.
#6
Originally Posted by 9silverbird8
Just like it says. Anyone got any ideas for removing that sucker?
http://www.caseytool.com/twistsockets.html
Trending Topics
#9
TECH Fanatic
iTrader: (3)
Join Date: Jan 2003
Location: miami beach fl
Posts: 1,652
Likes: 0
Received 0 Likes
on
0 Posts
http://www.arizonatools.com/catalog/...1038&catId=116
will work
http://www.etoolcart.com/browseprodu...AHN-11135.HTML
is the kit I use
12 pt torx bits can also be pounded i nand used to remove em
I get to deal with lots of stripped allen and torx becasue the germans seem to think they are the cats *** ......................they arent
will work
http://www.etoolcart.com/browseprodu...AHN-11135.HTML
is the kit I use
12 pt torx bits can also be pounded i nand used to remove em
I get to deal with lots of stripped allen and torx becasue the germans seem to think they are the cats *** ......................they arent
#10
TECH Enthusiast
iTrader: (4)
Join Date: Aug 2003
Location: Phoenix AZ
Posts: 633
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by DynoDR
How about a "twist socket"?
http://www.caseytool.com/twistsockets.html
http://www.caseytool.com/twistsockets.html
best tool I bought off the matco lady
Originally Posted by tuff
If you had a welder you could weld a nut over the stud and weld through the nut to the stud like a plug weld.
#11
TECH Enthusiast
Thread Starter
iTrader: (19)
Join Date: Jun 2002
Location: San Francisco
Posts: 740
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by ta12sec
http://www.arizonatools.com/catalog/...1038&catId=116
will work
http://www.etoolcart.com/browseprodu...AHN-11135.HTML
is the kit I use
12 pt torx bits can also be pounded i nand used to remove em
I get to deal with lots of stripped allen and torx becasue the germans seem to think they are the cats *** ......................they arent
will work
http://www.etoolcart.com/browseprodu...AHN-11135.HTML
is the kit I use
12 pt torx bits can also be pounded i nand used to remove em
I get to deal with lots of stripped allen and torx becasue the germans seem to think they are the cats *** ......................they arent
#12
On The Tree
Join Date: Nov 2002
Location: Elizabethton, TN
Posts: 116
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by ta12sec
I get to deal with lots of stripped allen and torx becasue the germans seem to think they are the cats *** ......................they arent
#14
TECH Fanatic
iTrader: (27)
Please help!!!!!
Thanks in advance.
Last edited by jdoyle; 08-14-2012 at 11:32 PM.
#16
Moderator
iTrader: (11)
Join Date: Mar 2002
Location: East Central Florida
Posts: 12,604
Likes: 0
Received 6 Likes
on
6 Posts
Every motorcycle owner ought to have a hand impact driver.
They cost about 10-20 bucks and come with a 5/16" hex that
takes Philips (so you can back out those crusty Jap bike
case screws and replace them with Allens) and a 3/8" square
drive head (so you can put an Allen bit on there). A 2# baby
sledgehammer and a little wrist tension, and these suckers
work great. The happer forces the bit into the fastener just
when you need it to.
Not all of them come with the 3/8 square socket bit, watch
for that. The cheap $6.99 Harbor Freight one looks to not,
but I've picked up flea market ones for 5 bucks that did.
http://www.sears.com/shc/s/p_10153_12605_SPM3278860402P
They cost about 10-20 bucks and come with a 5/16" hex that
takes Philips (so you can back out those crusty Jap bike
case screws and replace them with Allens) and a 3/8" square
drive head (so you can put an Allen bit on there). A 2# baby
sledgehammer and a little wrist tension, and these suckers
work great. The happer forces the bit into the fastener just
when you need it to.
Not all of them come with the 3/8 square socket bit, watch
for that. The cheap $6.99 Harbor Freight one looks to not,
but I've picked up flea market ones for 5 bucks that did.
http://www.sears.com/shc/s/p_10153_12605_SPM3278860402P
#18
Staging Lane
iTrader: (1)
Every motorcycle owner ought to have a hand impact driver.
They cost about 10-20 bucks and come with a 5/16" hex that
takes Philips (so you can back out those crusty Jap bike
case screws and replace them with Allens) and a 3/8" square
drive head (so you can put an Allen bit on there). A 2# baby
sledgehammer and a little wrist tension, and these suckers
work great. The happer forces the bit into the fastener just
when you need it to.
Not all of them come with the 3/8 square socket bit, watch
for that. The cheap $6.99 Harbor Freight one looks to not,
but I've picked up flea market ones for 5 bucks that did.
http://www.sears.com/shc/s/p_10153_12605_SPM3278860402P
They cost about 10-20 bucks and come with a 5/16" hex that
takes Philips (so you can back out those crusty Jap bike
case screws and replace them with Allens) and a 3/8" square
drive head (so you can put an Allen bit on there). A 2# baby
sledgehammer and a little wrist tension, and these suckers
work great. The happer forces the bit into the fastener just
when you need it to.
Not all of them come with the 3/8 square socket bit, watch
for that. The cheap $6.99 Harbor Freight one looks to not,
but I've picked up flea market ones for 5 bucks that did.
http://www.sears.com/shc/s/p_10153_12605_SPM3278860402P
The nature of combining steel fastener and aluminum, over time, vibration, expansion, contraction and galvanic action will ended up with difficulty in fastener removal.
I have SnapOn, IMO, use good tools to avoid the painfull damage controls!
#19
Moderator
iTrader: (11)
Join Date: Mar 2002
Location: East Central Florida
Posts: 12,604
Likes: 0
Received 6 Likes
on
6 Posts
The cool thing about the hand tool is that you're actually
driving the bit into the workpiece just when you need the
seating force to fight cam-out. An impact gun, you can lean
into it but that's still only a hundred or so pounds of in-force
(unless you're sitting on it). But the "impact" is pure rotary.
If the Allen in question is rounded beyond help, another
idea might be to get a slightly oversized Torx bit, call it
expendable and use the hand impact tool to pound it in
and hopefully grab. Maybe bevel the lead face a hair, to
help it in.
driving the bit into the workpiece just when you need the
seating force to fight cam-out. An impact gun, you can lean
into it but that's still only a hundred or so pounds of in-force
(unless you're sitting on it). But the "impact" is pure rotary.
If the Allen in question is rounded beyond help, another
idea might be to get a slightly oversized Torx bit, call it
expendable and use the hand impact tool to pound it in
and hopefully grab. Maybe bevel the lead face a hair, to
help it in.
#20
Staging Lane
iTrader: (1)
The cool thing about the hand tool is that you're actually
driving the bit into the workpiece just when you need the
seating force to fight cam-out. An impact gun, you can lean
into it but that's still only a hundred or so pounds of in-force
(unless you're sitting on it). But the "impact" is pure rotary.
If the Allen in question is rounded beyond help, another
idea might be to get a slightly oversized Torx bit, call it
expendable and use the hand impact tool to pound it in
and hopefully grab. Maybe bevel the lead face a hair, to
help it in.
driving the bit into the workpiece just when you need the
seating force to fight cam-out. An impact gun, you can lean
into it but that's still only a hundred or so pounds of in-force
(unless you're sitting on it). But the "impact" is pure rotary.
If the Allen in question is rounded beyond help, another
idea might be to get a slightly oversized Torx bit, call it
expendable and use the hand impact tool to pound it in
and hopefully grab. Maybe bevel the lead face a hair, to
help it in.
Not trying to be argumentive, TIA!!