84 Corvette with LS1 engine and transmission
11-28-2007, 03:24 PM
#1
On The Tree
Thread Starter
iTrader: (47)
Join Date: Mar 2006
Location: melbourne FL
Posts: 172
Likes: 0
Received 0 Likes
on
0 Posts
84 Corvette with LS1 engine and transmission I bought this car from Mario Cabrera (a Corvette Forum Member) and it was built by Trace Torrence (also a Corvette Forum Member) in Houston, Texas. I bought it with no transmission, torque arm, driveshaft and exhaust. I had a local Florida shop install a new 4l60e transmission and Torque arm adapter as well as the exhaust. It is an awesome car and built very well. I am selling the car because I have a new baby on the way.
The car is street legal with catalytic converters. The odometer is showing 0000 as it is new as with most components being replaced or upgraded. I believe is has low miles, under 100k. It was built to compete with C5 Corvettes but I have not raced it SCCA yet but it does very well around town.
Asking $8500 obo and I'm open to offers
I am in Melbourne, Florida
PM with questions and contact info please @ rich.wesson@earthlink.net
CHASSIS
Poly bushings, front and rear
Sloted brakes up front
Hawk HPS pads
Stainless steel braided brake lines
(4) Koni shocks
Lowered front and rear 2.25 inches with Vette brakes springs
(4) Genuine C5 Z06 wheels with Michelin Pilot rubber.
Camber brace
Speed bleeders in all 4 calipers
32 mm front sway bar
26 mm rear sway bar
ENGINE
2001 engine rebuilt 10,000 miles ago with F-body oil pan and intake manifold
AC needs compressor mounted on LS1
S&P Power steering pulley set
C5 Corvette Alternator and power steering pump\Reservoir and water pump
New aluminum Radiator
Corvette C5 motor mounts
GM stock Lucas 28 lb fuel injectors
160 degree thermostat
LS1 coil on Plug
Splitfire spark plugs
Precats and main cat with stock mufflers for passing inspection and emissions for now
Smog pump removed
S&P Braided stainless steel feed and return fuel lines
S&P fuel rails from 98 vette with new fuel pump and filter
S&P custom engine harness with 98 custom programmed computer.
Taylor silicone plug wires
TRANSMISSION
4L60E Rebuilt and installed by Automatic Specialties
Upgraded clutch package
Reworked valve body for firm shifts
Rebuilt torque converter
Custom polished Aluminum C-beam and driveshaft
Custom torque arm adapter
Rebuilt Dana 36 posi with 3:73 gears
INTERIOR
Has Alpine CD player CDA-7822 and custom rear speaker box.
Newly upholstered leather seats
Custom dash with new GM Electric Gauges
Has black console and black passenger side bread box now.
The car is street legal with catalytic converters. The odometer is showing 0000 as it is new as with most components being replaced or upgraded. I believe is has low miles, under 100k. It was built to compete with C5 Corvettes but I have not raced it SCCA yet but it does very well around town.
Asking $8500 obo and I'm open to offers
I am in Melbourne, Florida
PM with questions and contact info please @ rich.wesson@earthlink.net
CHASSIS
Poly bushings, front and rear
Sloted brakes up front
Hawk HPS pads
Stainless steel braided brake lines
(4) Koni shocks
Lowered front and rear 2.25 inches with Vette brakes springs
(4) Genuine C5 Z06 wheels with Michelin Pilot rubber.
Camber brace
Speed bleeders in all 4 calipers
32 mm front sway bar
26 mm rear sway bar
ENGINE
2001 engine rebuilt 10,000 miles ago with F-body oil pan and intake manifold
AC needs compressor mounted on LS1
S&P Power steering pulley set
C5 Corvette Alternator and power steering pump\Reservoir and water pump
New aluminum Radiator
Corvette C5 motor mounts
GM stock Lucas 28 lb fuel injectors
160 degree thermostat
LS1 coil on Plug
Splitfire spark plugs
Precats and main cat with stock mufflers for passing inspection and emissions for now
Smog pump removed
S&P Braided stainless steel feed and return fuel lines
S&P fuel rails from 98 vette with new fuel pump and filter
S&P custom engine harness with 98 custom programmed computer.
Taylor silicone plug wires
TRANSMISSION
4L60E Rebuilt and installed by Automatic Specialties
Upgraded clutch package
Reworked valve body for firm shifts
Rebuilt torque converter
Custom polished Aluminum C-beam and driveshaft
Custom torque arm adapter
Rebuilt Dana 36 posi with 3:73 gears
INTERIOR
Has Alpine CD player CDA-7822 and custom rear speaker box.
Newly upholstered leather seats
Custom dash with new GM Electric Gauges
Has black console and black passenger side bread box now.
Last edited by 72Elkytpi; 03-03-2008 at 07:21 AM.
11-29-2007, 09:54 PM
#2
On The Tree
Thread Starter
iTrader: (47)
Join Date: Mar 2006
Location: melbourne FL
Posts: 172
Likes: 0
Received 0 Likes
on
0 Posts
I would like to sell this car so Im negotiable on price. I bought it, put the tranny in and now Im getting very busy so I am going to let it go.
so let me know what you think
thanks
Next step is Ebay
so let me know what you think
thanks
Next step is Ebay
Last edited by 72Elkytpi; 02-21-2008 at 12:01 PM.
12-03-2007, 01:57 PM
#7
On The Tree
Thread Starter
iTrader: (47)
Join Date: Mar 2006
Location: melbourne FL
Posts: 172
Likes: 0
Received 0 Likes
on
0 Posts
LS engines are fun to work on. There is no BS with getting the distributor to go in on the correct tooth. GM has done some great work designing.
Trending Topics
02-26-2008, 01:38 PM
#12
On The Tree
Thread Starter
iTrader: (47)
Join Date: Mar 2006
Location: melbourne FL
Posts: 172
Likes: 0
Received 0 Likes
on
0 Posts
Im sure its nice, Im not into red interiors though. In fact I think Im going to change out my blue interior for black.
Noone seems to have any money right now anyway.
What do you guys think of swapping in the 91-96 interior into the 84-90 vettes.
Noone seems to have any money right now anyway.
What do you guys think of swapping in the 91-96 interior into the 84-90 vettes.
