My Custom Set Of Torque Thrust II
07-17-2010, 03:56 PM
#101
those look so bad *** .. im thinking of getting a pair like those for the rear of my 94
formula ..only with the centers in black or gunmetal powdercoat. my car is bright red.
formula ..only with the centers in black or gunmetal powdercoat. my car is bright red.
12-16-2010, 10:42 PM
#104
You aren't going to be able to get a lip bigger than the standard 17x11's and tuck them within the fenders without a narrowed rear....... Page two shows his custom wheels on a standard length rear, and as you can see, they stick out probably 2" on either side. I'm not sure what exactly you're asking otherwise.
12-16-2010, 11:10 PM
#105
i know they have a big lip but the off set is 17x11 why do they stick out so much if they are 17x11's?is it the lip? I has 17x11 with 315's and didnt stick out like that. what all needs to be done to narrow a rear end?I really want to do this to my car.thanks guys and sorry I dont know much about this dept
12-17-2010, 04:36 AM
#106
i know they have a big lip but the off set is 17x11 why do they stick out so much if they are 17x11's?is it the lip? I has 17x11 with 315's and didnt stick out like that. what all needs to be done to narrow a rear end?I really want to do this to my car.thanks guys and sorry I dont know much about this dept
For example: I have 15x10 bogarts for the rear of my SS. to make a 15x10" wide wheel fit correctly with a factory width rearend on our cars you need a wheel with 7.5" of back spacing. I decided that I wanted a "deeper dish" so I ordered a MWC fab9 rearend that had been narrowed 3" per side, thus giving me the opportunity of 3" of extra dish to the wheel vs the standard setup.
When I ordered wheels I now had to order a 15X10" wheel that had a 4.5" backspacing, since the rearend is narrowed 3" this put the outer edge of the wheel in the same location a stock but gave me TONS of extra dish.
If I were to put a the standard 7.5" BS wheel on the rear of my car now it would sit inboard 3" and look ridicules, on the same note if I was to put my custom 4.5" BS wheels on the back of a factory width F-body they would not have enough BS and would stick out 3" past the quarter panel and look like something you might see driving through the barrio.
Hope this helps you put it into perspective.
12-17-2010, 10:02 AM
#107
11 Second Club
Thread Starter
iTrader: (35)
Join Date: Dec 2004
Location: NW Chicago burbs
Posts: 2,163
Likes: 0
Received 0 Likes
on
0 Posts
i know they have a big lip but the off set is 17x11 why do they stick out so much if they are 17x11's?is it the lip? I has 17x11 with 315's and didnt stick out like that. what all needs to be done to narrow a rear end?I really want to do this to my car.thanks guys and sorry I dont know much about this dept
03-02-2011, 10:56 AM
#109
TECH Apprentice
iTrader: (13)
Join Date: Jan 2008
Location: godley
Posts: 334
Likes: 0
Received 0 Likes
on
0 Posts
I just bought a rear yesterday and suppose to be 2" per side . Do you have the flange to flange measurement from your rear So I can double check mine and if mine is 2 what offset should I order with the 12" wide wheel? What is the widest tire that will work with bfh/bumpstop/rolled fenders?I appreciate your help. Thanks
Looks good!
03-02-2011, 09:18 PM
#111
11 Second Club
Thread Starter
iTrader: (35)
Join Date: Dec 2004
Location: NW Chicago burbs
Posts: 2,163
Likes: 0
Received 0 Likes
on
0 Posts
I have the measurements laying around in the garage I believe. Your wheel / Tire combo is going to be dependant on you.
I would install the rear end and then measure how you want the wheels to fit & sit. I did it the oppsite and had to order another set because I didn't like how the wheels sat in the fender.
The rule has been 2'' off each side of the rear end means 2'' off the stock backspacing but that run didn't work for me and my wheels were tucked too much for my liking. I ended up with a backspacing for a rear end cut almost 3'' on each side to have my wheels sit with no rubbing issues and no clearance issues.
I would install the rear end and then measure how you want the wheels to fit & sit. I did it the oppsite and had to order another set because I didn't like how the wheels sat in the fender.
The rule has been 2'' off each side of the rear end means 2'' off the stock backspacing but that run didn't work for me and my wheels were tucked too much for my liking. I ended up with a backspacing for a rear end cut almost 3'' on each side to have my wheels sit with no rubbing issues and no clearance issues.
03-02-2011, 09:29 PM
#112
11 Second Club
Thread Starter
iTrader: (35)
Join Date: Dec 2004
Location: NW Chicago burbs
Posts: 2,163
Likes: 0
Received 0 Likes
on
0 Posts
17x11 with 5.75 backspacing since my rear was cut 2'' each side. (didn't like how they tucked)
So I measured instead of following the rule and these sit to more of my liking and are 1'' wider then the previous set. No spacers, No tricks Just ordered another set of wheels with different offset
So I measured instead of following the rule and these sit to more of my liking and are 1'' wider then the previous set. No spacers, No tricks Just ordered another set of wheels with different offset
03-28-2011, 08:36 AM
#114
On The Tree
iTrader: (3)
Join Date: Aug 2004
Location: Oxford
Posts: 163
Likes: 0
Received 0 Likes
on
0 Posts
So TOMZWHEELS is apparently out of business now.
Any recommendations for a place to order custom wheels like this?
Also, has anyone tried to get a very narrow set of front TT2 wheels, like 17x4?
Thx.
Any recommendations for a place to order custom wheels like this?
Also, has anyone tried to get a very narrow set of front TT2 wheels, like 17x4?
Thx.
