*The Fikse FM5 thread*
*The Fikse FM5 thread* I'm going to order these wheels in a few months and I'm confused on what finish to go with. Can you guys/gals post your cars with FM5's, finish of the wheels, size, & offsets?
Profil 5's....first of their kind (for 4th gen's) in this finish.
18 x 9.5 (+38mm - offset to clear CTS-V binders)
18 x 11 (+19 - 1" narrowed rear)
Simulated install on the car...
18 x 9.5 (+38mm - offset to clear CTS-V binders)
18 x 11 (+19 - 1" narrowed rear)
Simulated install on the car...
Last edited by LPE 403; Jul 26, 2011 at 02:19 PM.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
How much did you get those Azenis tires for? I have been searching around trying to get ideas without paying 300 a tire.
Tires should last a few years or few days depending on how heavy the foot is 
FormerVendor
Joined: May 2010
Posts: 276
Likes: 11
Fikse,
Sorry, don't mean to hijack, but noticed you on the forum. What can be done about older Fikse wheels that need some TLC? My centers (FM10s) have some etching
on them. All I ever did was wash with soap and water. Thought about sending the centers to get powder coated, but don't have the torque specs for the bolts and believe I would need to order new bolts from you?
Any help or feedback would be appreciated!
Sorry, don't mean to hijack, but noticed you on the forum. What can be done about older Fikse wheels that need some TLC? My centers (FM10s) have some etching
on them. All I ever did was wash with soap and water. Thought about sending the centers to get powder coated, but don't have the torque specs for the bolts and believe I would need to order new bolts from you?Any help or feedback would be appreciated!
FormerVendor
Joined: May 2010
Posts: 276
Likes: 11
Fikse,
Sorry, don't mean to hijack, but noticed you on the forum. What can be done about older Fikse wheels that need some TLC? My centers (FM10s) have some etching on them. All I ever did was wash with soap and water. Thought about sending the centers to get powder coated, but don't have the torque specs for the bolts and believe I would need to order new bolts from you?
Any help or feedback would be appreciated!
Sorry, don't mean to hijack, but noticed you on the forum. What can be done about older Fikse wheels that need some TLC? My centers (FM10s) have some etching
on them. All I ever did was wash with soap and water. Thought about sending the centers to get powder coated, but don't have the torque specs for the bolts and believe I would need to order new bolts from you?Any help or feedback would be appreciated!
If y'all are referring to the first picture of the Maroon Car from post #12, if you will look closer you will notice that the car is half way on a drive way entrance. It gives the appearance it is super low. Not all four wheels are on the same surface.