How much do tweeter pods cost?
TECH Addict
Joined: Sep 2006
Posts: 2,591
Likes: 1
From: Massachusetts
It's possible that a deep tweeter will work, but it depends on the outside diameter. I would say most likely it will not work, though.
I use Seas Neo tweeters in my custom setup. They're amazing. They fit ok in the tweeter pods, though they look like *** the way I have them :/ I had cut a big hole for my old tweeters, and switched over to the smaller Seas ones, so I was like F it and used epoxy putty to hold them in. It looks SO DAMN BAD lol
I use Seas Neo tweeters in my custom setup. They're amazing. They fit ok in the tweeter pods, though they look like *** the way I have them :/ I had cut a big hole for my old tweeters, and switched over to the smaller Seas ones, so I was like F it and used epoxy putty to hold them in. It looks SO DAMN BAD lol
"mark,
got the tweeter pods started, I wasted about half the day when I decided to double check and make sure they would work with the majority of tweeters and realized they were about half an inch to shallow. I've cut parts for three pairs and I'll glass them up this week. According to the specs on crutchfield they should fit 85% of the tweeters out there.
Just a general update.
Jason"
Soon my peeps, soon
Also, this is the guy I trusted with our Targa Roof so trust me, they will be bitchin 
got the tweeter pods started, I wasted about half the day when I decided to double check and make sure they would work with the majority of tweeters and realized they were about half an inch to shallow. I've cut parts for three pairs and I'll glass them up this week. According to the specs on crutchfield they should fit 85% of the tweeters out there.
Just a general update.
Jason"
Soon my peeps, soon
Also, this is the guy I trusted with our Targa Roof so trust me, they will be bitchin 
Staging Lane
Joined: Nov 2005
Posts: 87
Likes: 0
From: Austin, Texas
Yes, if my tweeters can fit (hopefully flush-mounted,) in these pods, I will buy ASAP... I have funds set aside for this. Give me the word, (and a few pics,) and I'm on-board.
http://www.edesignaudio.com/product_...roducts_id=617
Tweeter mounting depth = 1.78"
Tweeter overall diameter = 1.725"
http://www.edesignaudio.com/product_...roducts_id=617
Tweeter mounting depth = 1.78"
Tweeter overall diameter = 1.725"
Staging Lane
Joined: Nov 2005
Posts: 87
Likes: 0
From: Austin, Texas
I can take a picture of them mounted in my doors, if that will help--but I'd rather not remove them. They fit in the stock tweeterpod no problem...
Can you measure the internal cavity/mounting depth of the pod? I guess it won't be the end of the world if I have to mount it non-flush, but that sure would be nice. A lot of it depends on how you have designed them.
Can you measure the internal cavity/mounting depth of the pod? I guess it won't be the end of the world if I have to mount it non-flush, but that sure would be nice. A lot of it depends on how you have designed them.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo Staging Lane
Joined: Nov 2005
Posts: 87
Likes: 0
From: Austin, Texas
All I can think about is how much better my setup will sound when I get these. I can't stand that my legs, and my passenger's always block the tweeters!
I just hope y'all can make them look relatively-stock.
I'll probably load my old tweeters in the stock panels--just because. I will have to tinker with the setup though, because it could really, really ruin the soundstage. For some reason I am really bothered by having the stock door pods, and not having anything in the tweeter location
I just hope y'all can make them look relatively-stock.
I'll probably load my old tweeters in the stock panels--just because. I will have to tinker with the setup though, because it could really, really ruin the soundstage. For some reason I am really bothered by having the stock door pods, and not having anything in the tweeter location
Thread Starter
Banned
iTrader: (56)
Joined: Jul 2004
Posts: 12,637
Likes: 4
From: Valley Village, CA
UPDATES Here we go...
"Sorry for the late reply, I've had my phone off for the last three days cause everytime I pick it up I get ordered in to work.
Once again cell phone pics, but they seem to be pretty good. I read the thread and got some pics with a tape measure so people can see the size. It's too dark for installed pics, I can get some tomorrow. Depth is right about 1 1/3 and the mounting pad for the tweeter is about 2 1/4. It mounts with a single attachment point. From what I've seen on crutchfield this should accommodate most tweeters out there.
The mounting pad hole can be cut for anysize tweeter. I can also leave it uncut if the buyers wants to do it themselves.
I can paint them black, do a rough textured finish or send them out in primer.
I'm just starting to get a few pair going and will finish them up while I'm waiting for things to dry with the targa mold.
I can start taking orders on the 20th.
The targa mold is getting a bit more work on the flanges done. I'm sealing it on wed and will layup the first piece this weekend. I'll bond the latches on next wednesday/ do a test fitment and go for a test drive at the end of the week after the adhesive has had a few days to dry.
Hope this is all good news, gotta get up in 4hrs.
Jason"
Looks like May will be an exciting month for F-Bodies
Here we go..."Sorry for the late reply, I've had my phone off for the last three days cause everytime I pick it up I get ordered in to work.
Once again cell phone pics, but they seem to be pretty good. I read the thread and got some pics with a tape measure so people can see the size. It's too dark for installed pics, I can get some tomorrow. Depth is right about 1 1/3 and the mounting pad for the tweeter is about 2 1/4. It mounts with a single attachment point. From what I've seen on crutchfield this should accommodate most tweeters out there.
The mounting pad hole can be cut for anysize tweeter. I can also leave it uncut if the buyers wants to do it themselves.
I can paint them black, do a rough textured finish or send them out in primer.
I'm just starting to get a few pair going and will finish them up while I'm waiting for things to dry with the targa mold.
I can start taking orders on the 20th.
The targa mold is getting a bit more work on the flanges done. I'm sealing it on wed and will layup the first piece this weekend. I'll bond the latches on next wednesday/ do a test fitment and go for a test drive at the end of the week after the adhesive has had a few days to dry.
Hope this is all good news, gotta get up in 4hrs.
Jason"
Looks like May will be an exciting month for F-Bodies
Thread Starter
Banned
iTrader: (56)
Joined: Jul 2004
Posts: 12,637
Likes: 4
From: Valley Village, CA
Don't know why but reading back through this thread your post made me think of that (not for the lunch thing either, I already paid
) 
, but is there an update? In one of the posts, you/your supplier said you could start taking orders today. Just curious! Thread Starter
Banned
iTrader: (56)
Joined: Jul 2004
Posts: 12,637
Likes: 4
From: Valley Village, CA
I was told I'd get pics of the finished first set this weekend 