DYNO Results ! 68 Cutlass / LS1 / A4
#1
Staging Lane
Thread Starter
iTrader: (2)
Join Date: May 2007
Location: Minnetonka, MN
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
DYNO Results ! 68 Cutlass / LS1 / A4
My conversion is mostly complete. Complete enough for a final tune anyway.
I need to post some pics. I'll get to that in the next few days.
My build: 2002 LS1 with 20K miles, 4L60E, Hightech Motorsports (Elk River MN) reverse split cam 230/226 ground by Comp. Springs & push-rods, Around 3K Coan stall with lock-up. Hooker supercomp swap headders, full 2 1/2" dual exhaust with cross pipe. BRP engine mounting. Spearthech Harness. B-Body plastic tank with Walbro pump. 3.08 gears out back hope to change to 3.42. Electric fans from a Dodge Concord to mix things up!
After purging the fuel line, this fired for the first time so fast I nearly crapped my pants.
I haven't done this before so someone review my results:
Near 370 at the wheels!
Eric
I need to post some pics. I'll get to that in the next few days.
My build: 2002 LS1 with 20K miles, 4L60E, Hightech Motorsports (Elk River MN) reverse split cam 230/226 ground by Comp. Springs & push-rods, Around 3K Coan stall with lock-up. Hooker supercomp swap headders, full 2 1/2" dual exhaust with cross pipe. BRP engine mounting. Spearthech Harness. B-Body plastic tank with Walbro pump. 3.08 gears out back hope to change to 3.42. Electric fans from a Dodge Concord to mix things up!
After purging the fuel line, this fired for the first time so fast I nearly crapped my pants.
I haven't done this before so someone review my results:
Near 370 at the wheels!
Eric
#6
Staging Lane
Thread Starter
iTrader: (2)
Join Date: May 2007
Location: Minnetonka, MN
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
Ya, I'll work on the pics.
I haven't gotten my foot into it yet. I wanted to wait until after the dyno tune which was yesterday. It wouldn't run without leaving a big vacuum leak out the side of the throttle body. The tuner quickly took care of that.
There was light rain on the way home so I didn't dare get too agressive.
Maybe tonight!
Can anyone digest the graph from the dyno tune? The peak numbers look good but what do others think about the "area under the line"
Eric
I haven't gotten my foot into it yet. I wanted to wait until after the dyno tune which was yesterday. It wouldn't run without leaving a big vacuum leak out the side of the throttle body. The tuner quickly took care of that.
There was light rain on the way home so I didn't dare get too agressive.
Maybe tonight!
Can anyone digest the graph from the dyno tune? The peak numbers look good but what do others think about the "area under the line"
Eric
#7
TECH Fanatic
iTrader: (8)
Ya, I'll work on the pics.
I haven't gotten my foot into it yet. I wanted to wait until after the dyno tune which was yesterday. It wouldn't run without leaving a big vacuum leak out the side of the throttle body. The tuner quickly took care of that.
There was light rain on the way home so I didn't dare get too agressive.
Maybe tonight!
Can anyone digest the graph from the dyno tune? The peak numbers look good but what do others think about the "area under the line"
Eric
I haven't gotten my foot into it yet. I wanted to wait until after the dyno tune which was yesterday. It wouldn't run without leaving a big vacuum leak out the side of the throttle body. The tuner quickly took care of that.
There was light rain on the way home so I didn't dare get too agressive.
Maybe tonight!
Can anyone digest the graph from the dyno tune? The peak numbers look good but what do others think about the "area under the line"
Eric
id also like to see some pics
Trending Topics
#9
Staging Lane
Thread Starter
iTrader: (2)
Join Date: May 2007
Location: Minnetonka, MN
Posts: 66
Likes: 0
Received 0 Likes
on
0 Posts
68 Cutlass LS1 pics
Here are a few pics. I was able to drive it in to work today.
There are a ferw details yet, like wiring for water temp guage wiich is the wire zip tied to the fuel rail. It also need a good clean-up.
Eric
There are a ferw details yet, like wiring for water temp guage wiich is the wire zip tied to the fuel rail. It also need a good clean-up.
Eric