silverstreak98maro

iTrader: (7)

Ive got a h/c car 373 rear gears n yank 4000 stall wanting to run 100/150 shot is the stall too big it is a tight stall through shark nozzle not plate any suggestions would be greatly appreciated thanx

red 95 t/a

TA6spdRDC

iTrader: (2)

You may be able to use it depending on what you shift at.

blackls1ta00

iTrader: (27)

*** it chev hit it and shift at 6600!lol

Nitro Dave's Nitrous Outlet

iTrader: (25)

If the stall actually stalls 4000 it is alittle loose for nitrous. That being said a 100 to 150 may not be an issue. You will just have to put it on and see. If its to loose send it to yank and have it restalled.
Dave

Ksths2

iTrader: (1)

I'm shootin 150 from the hit 100% w/ a 3.90 gear, using a 4000 vig converter.

Leaving about 2200rpms, footbrake, gets me 1.41 60's with my C5 on a QTP hoosier pullin the skinnies 4" & works great!

I will be the first though and say it seems tight for a 4000, it used to be a 3600 so i shipped it back & they changed it to 4000.

Only problem i've got is its super close to 7000rpms through the 1/4 traps! (I wish it was a 3.73 now lol)

algws6

iTrader: (3)

what size tire and what does it trap?

Ksths2

iTrader: (1)

im running Hoosier QTP 28x11.5x16 (true 10" tread) 129mph in 1/4, for some damn reason it won't break 130 lol

OH! and i drive it to the track w/ the A/C on & tunes blarrin!

algws6

iTrader: (3)

what did you have to do to get those big meats on there? 129/3.90s/7000, i wonder if your blowing through the convertor a bit.

Ksths2

iTrader: (1)

Nothin, bolted right up once i found the right offset rims. The only time they rub is when the tire grows with lots of mph, but they rubbed through the front of the plastic inner wheel well . No biggie though.
but yes they are very close all the way around, inside, outside etc.

StreetSilverado

iTrader: (17)

I think you'll be fine as long as you don't go over 150. I bet it'll start blowing through the converter if you do.

GIMPY02

Ive got a 4k stall vig converter stock heads comp cams si5 cam and on a 150 shot of nitros through a NOS plate system. Car 60's 1.37 on 26" mt drag radials

TA1364

iTrader: (11)

I think it will work, biggest problem will be trying to get it to hook. Ive spray 175 on a yank pt4400 but it definatly is turning some extra rpms up top.

shortdog

iTrader: (1)

Spraying over a 150 on a ss4000 here, shifting at around 6800 rpms. Went from a 26" tire/3.23, to a 28"/3.73, popped the rear end, back to a 3.23 until I get 9".

It might be a bit loose for the bottle, but I wanna run good on motor also.

TA1364

iTrader: (11)

What did your car run with that setup before it broke? Good to know someone has done it. I am going to try 175-200 on a cam only setup with a ss4000.

1badWS6

iTrader: (32)

GIMPY, what were your times with that set up you mentioned?

shortdog

iTrader: (1)

Bottom 10s @ 130+ two years ago, but my setup has changed a tad since then. Never got a chance to run a full pass with the 28" tires.

TA1364

iTrader: (11)

Nice. I'll be looking for some 10.20s at 131-133

Phantom

iTrader: (16)

We have a ss4000 in our trans am. 150 will be pushing its effective limits in my opinion