Molded Splash Guard for LS1, like Z06 Vette...
06-10-2009, 10:52 PM
#1
Launching!
Thread Starter
iTrader: (2)
Join Date: Feb 2008
Posts: 225
Likes: 0
Received 0 Likes
on
0 Posts
Molded Splash Guard for LS1, like Z06 Vette... Does anyone make them or has anyone just made them themselves?
My little 295's throw crap all over and I'd like to get that a bit under control and something like what the Z06 has would look good but I havent seen it done on a Camaro or seen anything close.
My little 295's throw crap all over and I'd like to get that a bit under control and something like what the Z06 has would look good but I havent seen it done on a Camaro or seen anything close.
06-11-2009, 04:01 AM
#5
Launching!
iTrader: (2)
Join Date: May 2007
Location: Camp Hill, Pa
Posts: 270
Likes: 0
Received 0 Likes
on
0 Posts
There are a couple of auto parts stores in my area that sell the molded splash guards specifically made for Camaros............was thinking they might look good especially if you shoot them the same color of the car......
06-11-2009, 09:20 AM
#7
12 Second Club
Join Date: Feb 2009
Location: AZ
Posts: 263
Likes: 0
Received 0 Likes
on
0 Posts
. I found factory one's on ebay but they just don't look tall enough. let me know if you figure something out. Trending Topics
06-11-2009, 09:39 AM
#8
TECH Enthusiast
iTrader: (4)
Join Date: Dec 2008
Location: Haverhill Ma
Posts: 628
Likes: 0
Received 0 Likes
on
0 Posts
Any tips on how to make these ourselves? Just buy ZR1 mudflaps and cut away until they fit or what? 6LE if you make these I'm buying them lol I need something because between rubber from the track getting all over my bumper or rock chips from driving down the gravel I need something to stop stuff flying off my tires!
06-11-2009, 11:40 AM
#9
12 Second Club
Join Date: Feb 2009
Location: AZ
Posts: 263
Likes: 0
Received 0 Likes
on
0 Posts
Any tips on how to make these ourselves? Just buy ZR1 mudflaps and cut away until they fit or what? 6LE if you make these I'm buying them lol I need something because between rubber from the track getting all over my bumper or rock chips from driving down the gravel I need something to stop stuff flying off my tires!
http://www.c5racer.com/catalog/#
they are the c6 splash guards.
06-11-2009, 05:44 PM
#11
I could do one of two things...
1) Sell you pre-cut ones to fit your car for $150 (my cost to buy is $125)
2) Sell you basically a reverse canard (like I make for the side splitters) for $75 raw aluminum, $100 powder coated satin black or textured black (to look like ABS) + shipping.
Who's down for what?
1) Sell you pre-cut ones to fit your car for $150 (my cost to buy is $125)
2) Sell you basically a reverse canard (like I make for the side splitters) for $75 raw aluminum, $100 powder coated satin black or textured black (to look like ABS) + shipping.
Who's down for what?
06-11-2009, 07:49 PM
#12
On The Tree
iTrader: (1)
Join Date: Oct 2002
Location: Ontario, CA
Posts: 103
Likes: 0
Received 0 Likes
on
0 Posts
I could do one of two things...
1) Sell you pre-cut ones to fit your car for $150 (my cost to buy is $125)
2) Sell you basically a reverse canard (like I make for the side splitters) for $75 raw aluminum, $100 powder coated satin black or textured black (to look like ABS) + shipping.
Who's down for what?
1) Sell you pre-cut ones to fit your car for $150 (my cost to buy is $125)
2) Sell you basically a reverse canard (like I make for the side splitters) for $75 raw aluminum, $100 powder coated satin black or textured black (to look like ABS) + shipping.
Who's down for what?
Last edited by 2000SSgeorge; 06-11-2009 at 07:50 PM. Reason: .
Table read for a film that day... 
