86 5.3 C10 Swap
#43
TECH Apprentice
Thread Starter
iTrader: (1)
Join Date: Mar 2011
Location: waverly, ohio
Posts: 315
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Everything is together all the fluids are topped off and turned the key and nothing. I didn't have much time to do much i did swap the coil connectors and still it just cranked. I noticed it didn't turn over to fast. The MSD is grounded to the back of the head a.d the hot wire is connected to the old coil wire. I haven't checked for spark yet. That's on the agenda along with a bigger batt'ry. If all else fails Im going to need a crank or cam sensor.
#44
TECH Apprentice
Thread Starter
iTrader: (1)
Join Date: Mar 2011
Location: waverly, ohio
Posts: 315
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I was wrong to jump to conclusions about a sensor. I regrounded my negative cable and it fired right up. Now i get to work on something else like my caprice then again one project is never really done, lol.
#46
TECH Apprentice
Thread Starter
iTrader: (1)
Join Date: Mar 2011
Location: waverly, ohio
Posts: 315
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Im glad my box didn't fry either. I did get to take the truck out. It ran great it wanted to stumble a little bit, it may have been where it wasn't warmed up. I think i may need to invest in another cooling fan or i got some grime in the steam port piping because it got a little hot when i pulled in the driveway.
#49
#51
TECH Apprentice
Thread Starter
iTrader: (1)
Join Date: Mar 2011
Location: waverly, ohio
Posts: 315
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I went to napa and got a p/s repair line. It came with a 16mm fitting and 6" of hard line. I flared the other end of it and put a 3/8" hard line fitting. I think the threads were 5/8x11 or 5/8x18 and used a coupler. The other side i just used a hose clamp and a piece of rubber hose.
[IMG]
[/IMG]
[IMG]
![](http://i1259.photobucket.com/albums/ii543/Darren_Roar/20130515_121148_zpsf739fe93.jpg)
#55
TECH Apprentice
Thread Starter
iTrader: (1)
Join Date: Mar 2011
Location: waverly, ohio
Posts: 315
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
![Hijacked!](https://ls1tech.com/forums/images/smilies/myhijacked2.gif)
[IMG]
![](http://i1259.photobucket.com/albums/ii543/Darren_Roar/20130518_115455_zps85fcd84c.jpg)
Last edited by darren roar; 05-18-2013 at 11:26 AM.
#56
TECH Apprentice
Thread Starter
iTrader: (1)
Join Date: Mar 2011
Location: waverly, ohio
Posts: 315
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
A year later I've got around To The 5.3 that blew up in my truck. It lost compression and was over heating. The drivers side didn't look that bad when I took the head off but the passengers side was a different story. The passengers head has a chunk missing between 2 & 4 cylinder combustion chambers. Has anyone else seen this? The drivers side can this be honed out or does it need bored?
[IMG]
[/IMG]
[IMG]
[/IMG]
[IMG]
[/IMG]
[IMG]
![](http://i1259.photobucket.com/albums/ii543/Darren_Roar/Mobile%20Uploads/20140521_005916_zpsvtshfdo2.jpg)
[IMG]
![](http://i1259.photobucket.com/albums/ii543/Darren_Roar/Mobile%20Uploads/20140521_010037_zps6vzwedgz.jpg)
[IMG]
![](http://i1259.photobucket.com/albums/ii543/Darren_Roar/Mobile%20Uploads/20140521_101647_zpsuaek5bhl.jpg)
#57
Staging Lane
Join Date: Feb 2014
Location: Pocatello Idaho
Posts: 81
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
truck looks good man,i had a question iam doing a similar swap5.3 l33 with a hair dryer on it. my question is how did you do your alternator wiring? i have the 2 wire plug in it,my battery is in the bed with the ground on the frame and positive ran to the starter. the wires i got from the junk yard had a battery cable for the negative side with a 8 or 10 pin plug in it.... what do i need to get this thing to charge?
#58
TECH Apprentice
Thread Starter
iTrader: (1)
Join Date: Mar 2011
Location: waverly, ohio
Posts: 315
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
truck looks good man,i had a question iam doing a similar swap5.3 l33 with a hair dryer on it. my question is how did you do your alternator wiring? i have the 2 wire plug in it,my battery is in the bed with the ground on the frame and positive ran to the starter. the wires i got from the junk yard had a battery cable for the negative side with a 8 or 10 pin plug in it.... what do i need to get this thing to charge?