97badass

iTrader: (8)

ok merv i screwed up... which way do the main caps go in the block? i know 1-5 starting in the front, but which direction

93Z2871805

iTrader: (5)

All of the numbers go on the driver's side of the block 1-4. 5 is the rear and the number goes to the passenger side. The "U" part of the 1 and 5 caps face inward.

97badass

iTrader: (8)

yeah i got it figured out 1-4 tabs to back 5 tab to front, next week the block goes to the machine shop. im delivering my t56 to the guy that bought it tonight, tomorrow im working on the engine bay, and saturday i work till noon so no progress till next week.

97badass

iTrader: (8)

engine is going to the machine shop monday after work, im picking up the rings and bearings probably tomorrow. the deal with the heads fell through, so back to finishing up the shortblock

97badass

iTrader: (8)

new bearings and rings ready to go in as soon as its back from the shop. and my cam will be here next week

97badass

iTrader: (8)

takes 3 days at the machine shop, so i rescheduled for wednesday so i actually have time to get everything else ready while im waiting. the engine bay is coming the rest of the way apart today so i can start painting it.

I-C5

iTrader: (1)

Nice man keep up the good work...my iron lq4/ ls2 is in the exact same stage as yours...at the shop getting cleaned up.

97badass

iTrader: (8)

i was planning on using the stock bottom end but a handful of sand fell down in it and i changed my mind real quick. plus cam bearings will be a breeze with no crank or rods in there

93Z2871805

iTrader: (5)

97badass

iTrader: (8)

i know, i know, i will get your pics when i get the engine back. thats when it should look like real progress! or it will still look the same, only clean...

ive got to get stuff powdercoated also.

97badass

iTrader: (8)

$145 to hone and tank it!

97badass

iTrader: (8)

the drivers side engine harness is a pitfa!!!!!!! but its out. i finally got the abs block out using a pipe wrench on the nuts. next step is pulling the front clip off and dropping the k member. then paint

97badass

iTrader: (8)

engine is getting the 5 stage hone tomorrow! its already been tanked once. the engine bay is stripped of everything electrical, brake booster steering column and tomorrow the front clip is coming off then friday the k member/front suspension to media blast the engine bay this weekend then im going to prime it after im done blasting and get it cleaned up. ive been taking pics when i remember.

the_merv

iTrader: (88)

Wtf is a stage 5 hone..lol

1961ba427

iTrader: (26)

I hope I'm wrong, but it sounds like several stages of extra billing is the difference between it and a good torque plate hone.

the_merv

iTrader: (88)

I hope they are using Torque Plates..

97badass

iTrader: (8)

yes its a torque plate hone and i think it is unnecessary for it. but 3 different grits then 2 polish using a cork stone. idfk but if the rings dont seal hes paying for it to be redone and new rings. hes the only shop i can make it to after work. the other guy ive always used wont stay later for me to get there. so im kinda stuck getting screwed on this deal

97badass

iTrader: (8)

well guys, its GO time... im going to have that front clip off tonight and hopefully the front suspension!
front clip is off besides the hood to cover up the empty engine bay

97badass

iTrader: (8)

anyone want pics? i got my engine back today

93Z2871805

iTrader: (5)

Post them up