The GMW - E36 with a 5.3 and a CD009
#243
TECH Junkie
iTrader: (1)
No - Ford went with a Volvo-style clutch cable on the foxbody. 😉
OEM Volvo clutch cable pulling on the slightly longer SN95 clutch arm, Quicktime bell, McLeod aluminum flywheel, Hayes clutch, Ford throw out bearing, Tremec T5z all behind the LS3.
OEM Volvo clutch cable pulling on the slightly longer SN95 clutch arm, Quicktime bell, McLeod aluminum flywheel, Hayes clutch, Ford throw out bearing, Tremec T5z all behind the LS3.
Last edited by Michael Yount; 04-14-2022 at 10:09 PM.
The following users liked this post:
G Atsma (04-14-2022)
The following users liked this post:
G Atsma (04-21-2022)
#246
Quick update. The car is running pretty solid. I saw some higher temps than I liked when sitting in traffic so I drained the cooling system, pulled vacuum on it, and pulled new coolant in. Since then she has been perfect. Took her out for a Memorial Day cruise and the car is so much fun to drive. Hope to get a real alignment done this week.
The following users liked this post:
G Atsma (05-31-2022)
#247
TECH Senior Member
This thing HAS to be making Beemer purists overstuff their panties,,,,
#248
Added 3rd center hood vent
Just added center hood vent.
also just installed f body ac compressor. Fits e36 w frame rail massage.
upping my elec fan combo from 1600 cfm cap to 3300cfm w custom shroud… hoping to be able to idle in Hou heat w ac.
Your car looks fun!
also just installed f body ac compressor. Fits e36 w frame rail massage.
upping my elec fan combo from 1600 cfm cap to 3300cfm w custom shroud… hoping to be able to idle in Hou heat w ac.
Your car looks fun!
#249
@G Atsma this car is like a Johnsonville sausage factory to those purists haha
@one4torque thanks man! I designed my louvers to be a little longer to allow for all that heat around the headers to escape (see below. Pay no attention to the terrible paint haha. That will eventually get addressed). After a 30 minutes of hard driving in almost 90 degree heat yesterday you could feel the heat pouring out of the vents. I put a IR temp gun on the louvers and there was almost a 40 degree delta between the louvers and the hood.
@one4torque thanks man! I designed my louvers to be a little longer to allow for all that heat around the headers to escape (see below. Pay no attention to the terrible paint haha. That will eventually get addressed). After a 30 minutes of hard driving in almost 90 degree heat yesterday you could feel the heat pouring out of the vents. I put a IR temp gun on the louvers and there was almost a 40 degree delta between the louvers and the hood.
The following users liked this post:
Michael Yount (05-31-2022)
The following users liked this post:
G Atsma (05-31-2022)
The following 4 users liked this post by TNspeed1:
#254
Quick update. The car has been running great. Still need to get a full alignment done and hope to have that wrapped up before the end of month. Also I got tired of sliding around in the factory seat. I found a good deal on a very lightly used Corbeau FX1 seat. Unfortunately all of the mounts I tried placed the seat to close to the dash. Being 6'-5" I had to make my own seat mount and now everything is mounted perfectly in the car.
The following 2 users liked this post by TNspeed1:
Homer_Simpson (07-15-2022), Michael Yount (07-13-2022)
#256
@Michael Yount how the heck are you! I will definitely do that. I have it pretty close right now, but want a pro to dial it in. Also the same place will corner balance the car so I might be able to kill two birds with one stone.