Taking a stab at an LS engine in my '99 Sonoma
#23
TECH Enthusiast
Thread Starter
iTrader: (15)
Join Date: Jun 2005
Posts: 609
Likes: 0
Received 0 Likes
on
0 Posts
Still working on it. I will do some detailed pics of the steering knuckle once I get the other side off to compair.
Other than that. The calipers are CTS-v fronts, and the rotors are C-6 Vette Z-51's.
Other than that. The calipers are CTS-v fronts, and the rotors are C-6 Vette Z-51's.
#26
I'd like to add that I still need some parts. List below.
Need Corvette A/C compressor and braket. With bolts if can.
Need a 2000 + F-body engine harness for an A-4 trans. Would like to have no EGR. But will deal with it if I can get a harness soon. No AIR system.
If close enough, would like to buy a low mile 4L60E trans from an LS equiped car or truck.
Need a Corvette front belt drive system with balancer pully, alternator, power steering pump, idler and tensioner pullies, brakets and bolts. (might buy brand new if I have to)
I also am looking for a complete charcole grey interior swap. And a body harness from an all power extended cab 2 wd truck.
Need Corvette A/C compressor and braket. With bolts if can.
Need a 2000 + F-body engine harness for an A-4 trans. Would like to have no EGR. But will deal with it if I can get a harness soon. No AIR system.
If close enough, would like to buy a low mile 4L60E trans from an LS equiped car or truck.
Need a Corvette front belt drive system with balancer pully, alternator, power steering pump, idler and tensioner pullies, brakets and bolts. (might buy brand new if I have to)
I also am looking for a complete charcole grey interior swap. And a body harness from an all power extended cab 2 wd truck.
#27
TECH Junkie
iTrader: (11)
I'd like to add that I still need some parts. List below.
Need Corvette A/C compressor and braket. With bolts if can.
Need a 2000 + F-body engine harness for an A-4 trans. Would like to have no EGR. But will deal with it if I can get a harness soon. No AIR system.
If close enough, would like to buy a low mile 4L60E trans from an LS equiped car or truck.
Need a Corvette front belt drive system with balancer pully, alternator, power steering pump, idler and tensioner pullies, brakets and bolts. (might buy brand new if I have to)
I also am looking for a complete charcole grey interior swap. And a body harness from an all power extended cab 2 wd truck.
Need Corvette A/C compressor and braket. With bolts if can.
Need a 2000 + F-body engine harness for an A-4 trans. Would like to have no EGR. But will deal with it if I can get a harness soon. No AIR system.
If close enough, would like to buy a low mile 4L60E trans from an LS equiped car or truck.
Need a Corvette front belt drive system with balancer pully, alternator, power steering pump, idler and tensioner pullies, brakets and bolts. (might buy brand new if I have to)
I also am looking for a complete charcole grey interior swap. And a body harness from an all power extended cab 2 wd truck.
Russ
#28
TECH Resident
iTrader: (28)
Nice build...I'm putting a LS2 in my 2002 S10....I'm over on S10Forum as Petro...I'm still stuck on buying parts though....haha...It's gonna be a longer than expected..
http://www.s10forum.com/forum/f30/pe...roject-397265/
http://www.s10forum.com/forum/f30/pe...roject-397265/
#29
TECH Apprentice
iTrader: (2)
Join Date: Jul 2005
Location: Texas
Posts: 305
Likes: 0
Received 0 Likes
on
0 Posts
Hmmh,where are you located? I just gutted a 2003 S10 (reg cab)that has all charcoal grey interior. I have everything but seats and carpet. Dash,headliner,visors,kick panels,rear wall carpet, and sill plates. If you can use any of this let me know. The harness I have is reg cab no power options.
#30
TECH Resident
iTrader: (2)
I'd like to add that I still need some parts. List below.
Need Corvette A/C compressor and braket. With bolts if can.
Need a 2000 + F-body engine harness for an A-4 trans. Would like to have no EGR. But will deal with it if I can get a harness soon. No AIR system.
If close enough, would like to buy a low mile 4L60E trans from an LS equiped car or truck.
Need a Corvette front belt drive system with balancer pully, alternator, power steering pump, idler and tensioner pullies, brakets and bolts. (might buy brand new if I have to)
I also am looking for a complete charcole grey interior swap. And a body harness from an all power extended cab 2 wd truck.
Need Corvette A/C compressor and braket. With bolts if can.
Need a 2000 + F-body engine harness for an A-4 trans. Would like to have no EGR. But will deal with it if I can get a harness soon. No AIR system.
If close enough, would like to buy a low mile 4L60E trans from an LS equiped car or truck.
Need a Corvette front belt drive system with balancer pully, alternator, power steering pump, idler and tensioner pullies, brakets and bolts. (might buy brand new if I have to)
I also am looking for a complete charcole grey interior swap. And a body harness from an all power extended cab 2 wd truck.
#31
looking good. im starting mine soon. 02 s10 alum 5.7. i would rather do 6.0 iron, but i got a motor with a bad bearing for a fair price. as for the wiring, im looking into doing the same repin and reflash. what pcm does your 99 have, 0411?
#36
TECH Enthusiast
Thread Starter
iTrader: (15)
Join Date: Jun 2005
Posts: 609
Likes: 0
Received 0 Likes
on
0 Posts
The body harness is out of another truck with the correct BCM. But the engine harness is still up in the air. I may just bite the bullet and buy one. I think in the end, it will just be money well spent.
#38
TECH Enthusiast
Thread Starter
iTrader: (15)
Join Date: Jun 2005
Posts: 609
Likes: 0
Received 0 Likes
on
0 Posts
I have. Just been taking my sweet *** time. LOL. Most of my spare cash has been going to fund a new home. So the build is taking slower than ever now. But I have been working on the frame, and getting all the ZQ-8 parts. The motor is almost done now too. A few body parts have been taken care of like the bed and doors. I've gotten the body control harness and module to convert to power everything. It's getting there.