started the day with 3 pedals...finished with 2 pedals
#1
8 Second 6 Speed Director
Thread Starter
iTrader: (6)
Join Date: May 2002
Location: windsor, ont. canada - Home of the fastest LT1 6spd.
Posts: 3,293
Likes: 0
Received 1 Like
on
1 Post
started the day with 3 pedals...finished with 2 pedals (VIDEO LINK)
well my Liberty built trans has been working so well, i tried to find a few more hp to put through it. well i managed that, the car always keep me on my toes, so to speak (pun intended). today my pass on the bottle was absolutely wild!
i just installed a new set of lifters. went like so...
1.35 60' yanking the wheels and launching out of the hole a little bit bent outta shape, grab second gear and yank the wheels about 6-8" and i know i am on a pass, grab 3rd gear just before the 330' and that is where it got very ugly.
as i sit hear at my computer with my right fight elevated to help keep the swelling down on the 3 toes i think i might have broke, i am very thankful i paid $300 for a custom kevlar blanket for my bellhousing, no it didn't keep the track clean but there is only a small hole in my floor by my right foot, and the rest of the clutch and pressure plate were everywhere else!
much like last year when my G Force 3rd gear popped into 5 pieces, the motor revved up pretty quick on the jug, not a good thing. when i am up and moving properly i will do a compression check to see if i have any lifted ringlands, more than likely i do, but time will tell.
now you may be wondering about the title of the post..... when the clutch decided to leave it normal place of operation, parts of the bellhousing violently
impacted the floor, leaving me a tad bit on the gimpy side. well, needless to say next to the stud sitting on my floor from the flywheel after all of this, i found my gas pedal in it's final resting place!
all i know is i will be begging McLeod industries to get their bullet proof bell housing to the market ASAP! i have no idea how extensive the damage is, but it could've been contained with a proper bellhousing, which no one makes! i will see if someone can make a one of for me, because i like my feet right where they are!
my .02, never short cut on your safety equipment.
now i will remain 9oh until next year and i wil resume my quest for the next sinle digit. it is all GOOD
madman,
i added a quarter pound of air and tweaked the front shocks, and what i think also helped was increasing build time for the bottle. car left hard as hell that is by far the scariest my ride has ever been through the first 2 gears!
video:
http://videos.camaroz28.com/video/82...d6018464ad.htm
i just installed a new set of lifters. went like so...
1.35 60' yanking the wheels and launching out of the hole a little bit bent outta shape, grab second gear and yank the wheels about 6-8" and i know i am on a pass, grab 3rd gear just before the 330' and that is where it got very ugly.
as i sit hear at my computer with my right fight elevated to help keep the swelling down on the 3 toes i think i might have broke, i am very thankful i paid $300 for a custom kevlar blanket for my bellhousing, no it didn't keep the track clean but there is only a small hole in my floor by my right foot, and the rest of the clutch and pressure plate were everywhere else!
much like last year when my G Force 3rd gear popped into 5 pieces, the motor revved up pretty quick on the jug, not a good thing. when i am up and moving properly i will do a compression check to see if i have any lifted ringlands, more than likely i do, but time will tell.
now you may be wondering about the title of the post..... when the clutch decided to leave it normal place of operation, parts of the bellhousing violently
impacted the floor, leaving me a tad bit on the gimpy side. well, needless to say next to the stud sitting on my floor from the flywheel after all of this, i found my gas pedal in it's final resting place!
all i know is i will be begging McLeod industries to get their bullet proof bell housing to the market ASAP! i have no idea how extensive the damage is, but it could've been contained with a proper bellhousing, which no one makes! i will see if someone can make a one of for me, because i like my feet right where they are!
my .02, never short cut on your safety equipment.
now i will remain 9oh until next year and i wil resume my quest for the next sinle digit. it is all GOOD
madman,
i added a quarter pound of air and tweaked the front shocks, and what i think also helped was increasing build time for the bottle. car left hard as hell that is by far the scariest my ride has ever been through the first 2 gears!
video:
http://videos.camaroz28.com/video/82...d6018464ad.htm
Last edited by taner; 10-30-2007 at 06:58 AM.
#3
Banned
iTrader: (22)
Join Date: Jan 2004
Location: Schaumburg,IL
Posts: 4,957
Likes: 0
Received 0 Likes
on
0 Posts
glad to hear you didn't get hurt to bad...
I had a buddy almost lose his foot about 5 years ago as well when a SPEC clutch came apart. The gas pedal was cut off and had to be the most clean cut I ever seen.
he walked away with no issues other then a slightly damaged car
I had a buddy almost lose his foot about 5 years ago as well when a SPEC clutch came apart. The gas pedal was cut off and had to be the most clean cut I ever seen.
he walked away with no issues other then a slightly damaged car
#4
FormerVendor
iTrader: (37)
MAN THAT SUCKS!!!!!!!!!!!!!!!!!!, I am glad you weren't injured to badly. The bad thing is Mcleod told me they had to have 100 orders to even prototype a lt-1 blowproof bellhousing. Might want to add some 1/4 inch plate to the floor board in that area to prevent personal injury.
#6
8 Second 6 Speed Director
Thread Starter
iTrader: (6)
Join Date: May 2002
Location: windsor, ont. canada - Home of the fastest LT1 6spd.
Posts: 3,293
Likes: 0
Received 1 Like
on
1 Post
boom...
http://motorcitynationals.com/v-web/...bum294/DOC4982
launch...
http://motorcitynationals.com/v-web/...bum294/DOC4979
video to follow.
http://motorcitynationals.com/v-web/...bum294/DOC4982
launch...
http://motorcitynationals.com/v-web/...bum294/DOC4979
video to follow.
Trending Topics
#11
7 Second Club
iTrader: (5)
Join Date: Nov 2001
Location: Gainesville, Florida # of drag strips runs: ?!?!?
Posts: 8,834
Likes: 0
Received 1 Like
on
1 Post
Holy crap, man that sucks! Glad to hear you'll be okay to race another day.
And definately +1 on safety equipment thoughts, but that's another discussion entirely....
Derek
And definately +1 on safety equipment thoughts, but that's another discussion entirely....
Derek
#12
FormerVendor
iTrader: (37)
On an LT1 Bellhousing it is not as deep as the LS1/SBC. The LT1 is actually the shallowest one they make since it is a pull style clutch. He could convert the front plate and input shaft to an LS1 but that would be the only way it would work. Then he could use the LS1 hydraulics and a Scatter Shield for the LS1.
Amber
Amber
#15
8 Second 6 Speed Director
Thread Starter
iTrader: (6)
Join Date: May 2002
Location: windsor, ont. canada - Home of the fastest LT1 6spd.
Posts: 3,293
Likes: 0
Received 1 Like
on
1 Post
only 1 broken toe, the other one is severly bruised/sprained. i will be back to 100% or whatever that is for me soon enuff. thanks!
amber,
thanks for the tip, i have a feeling i may be at the Street twin's limit? dunno i am waiting for a call back from Mcleod. funny thing is i seem to break everything that never breaks, lol!!! i have had ZERO issues with the performance of the clutch. it is NOW seeing approx. 1000fwhp, and it was performing exactly as it was supposed to. maybe it was just due to be changed. or it could have been a flaw in the valeo pressure plate?
roman,
no idea how bad the car is, it sits in the trailer, i will get to it later.
amber,
thanks for the tip, i have a feeling i may be at the Street twin's limit? dunno i am waiting for a call back from Mcleod. funny thing is i seem to break everything that never breaks, lol!!! i have had ZERO issues with the performance of the clutch. it is NOW seeing approx. 1000fwhp, and it was performing exactly as it was supposed to. maybe it was just due to be changed. or it could have been a flaw in the valeo pressure plate?
roman,
no idea how bad the car is, it sits in the trailer, i will get to it later.
Last edited by taner; 11-06-2007 at 12:26 AM.
#17
8 Second 6 Speed Director
Thread Starter
iTrader: (6)
Join Date: May 2002
Location: windsor, ont. canada - Home of the fastest LT1 6spd.
Posts: 3,293
Likes: 0
Received 1 Like
on
1 Post
i spoke to mcleod, but not the exact person to answer that question, i believe it is high horsepower, but not yet certain. believe me i have put this clutch setup through it's paces over the years as my hp has increased in the car. it has been an awesome clutch setup. i highly recommend it to anyone making any amount of power! just be prepared to break a few parts
#19
TECH Fanatic
iTrader: (21)
Join Date: Feb 2006
Location: Allen Park, MI
Posts: 1,370
Likes: 0
Received 0 Likes
on
0 Posts
ya, makes me happy my clutch just stopped working instead of exploding like that at milan.
definately want to get the proper safety equipment for my car next year to save my car and myself.
definately want to get the proper safety equipment for my car next year to save my car and myself.
#20
TECH Fanatic
iTrader: (2)
Join Date: Jan 2004
Location: Ewing, NJ
Posts: 1,222
Likes: 0
Received 0 Likes
on
0 Posts
glad to hear you are gonna be ok. let me know what they say about the bell housings availability. i know someone who has wanted one for a while now for his blown LT1 and hasn't been able to find anything.