FAST90mm + QTP HVM LT's = *The Real Deal*
#1
!LS1 11 Second Club
Thread Starter
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Finalized Numbers
Old: 425/387 (LS6/SLP LT's/3" True Duals X dumped)
New: 458/403 (FAST90/QTP HVM/QTP ORY + SLP 2OTL)
Same Dyno. Same internals. Mother of All Bolt Ons Swap.
More info to follow.
Edit: Dyno sheet attached (458 was thru open cutouts - closed shown)... though not a direct back to back X to Y comparo (due to the other mods swapped), I hope this makes people realize that properly made Y-pipes put down the numbers.
Old: 425/387 (LS6/SLP LT's/3" True Duals X dumped)
New: 458/403 (FAST90/QTP HVM/QTP ORY + SLP 2OTL)
Same Dyno. Same internals. Mother of All Bolt Ons Swap.
More info to follow.
Edit: Dyno sheet attached (458 was thru open cutouts - closed shown)... though not a direct back to back X to Y comparo (due to the other mods swapped), I hope this makes people realize that properly made Y-pipes put down the numbers.
![](http://home.att.net/~carlos.ramirez1/wsb/media/116212/site1048.jpg)
Last edited by SouthFL.02.SS; 03-19-2005 at 10:19 AM.
#2
10 Second Club
iTrader: (5)
Join Date: Apr 2003
Location: Okinawa, Japan
Posts: 1,220
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
mother of bitch thats awesome for that TSP cam youre running, i need to try some of those headers and that dual cutout y-pipe, im still using Jet hot 1.75" headers and Mufflex y pipe with a 3" cutout in the I pipe, im also thinking of doing a 85mm lid and 85mm maf to replace the factory size stuff on my 90 90 combo
once again congrats
once again congrats
#3
!LS1 11 Second Club
Thread Starter
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
85mm lid, 85mm maf
1 3/4" QTP's
Cutouts only gained 1rwhp. The QTP ORY and the 2OTL flow like a ****.
I'm picking up the dyno info tomorrow, along with the car.
1 3/4" QTP's
Cutouts only gained 1rwhp. The QTP ORY and the 2OTL flow like a ****.
I'm picking up the dyno info tomorrow, along with the car.
#4
10 Second Club
iTrader: (5)
Join Date: Apr 2003
Location: Okinawa, Japan
Posts: 1,220
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
wow thats impressive i need to put mine on the dyno and see the difference of my cutout and SLP dual dual which supposedly flows alright
ok i was under the impression that you had the 1 7/8 headers with those collectors
sounds like you got a strong car there, do you happen to know the a/f and timing they put in there?
ok i was under the impression that you had the 1 7/8 headers with those collectors
sounds like you got a strong car there, do you happen to know the a/f and timing they put in there?
#5
!LS1 11 Second Club
Thread Starter
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by Kurtomac
wow thats impressive i need to put mine on the dyno and see the difference of my cutout and SLP dual dual which supposedly flows alright
ok i was under the impression that you had the 1 7/8 headers with those collectors
sounds like you got a strong car there, do you happen to know the a/f and timing they put in there?
ok i was under the impression that you had the 1 7/8 headers with those collectors
sounds like you got a strong car there, do you happen to know the a/f and timing they put in there?
Thanks!
Trending Topics
#8
!LS1 11 Second Club
Thread Starter
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by 30th t/a
that is 1 healthy motor. what are you hopen to run? high 10s?
#10
TECH Enthusiast
Join Date: Dec 2004
Location: Chattanooga
Posts: 576
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by gomer
Damn, my wife is really pissed at you right now. Your post is the one that made me go ahead and order my 90/90 setup ![Devil](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_devil.gif)
![Devil](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_devil.gif)
![Happy](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_stretch.gif)
Never tell her.. say well if you can't remember I'll be damned if I am going to tell you..etc
![Happy](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_stretch.gif)
![Happy](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_stretch.gif)
#13
LS1Tech Premium Sponsor
iTrader: (4)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Awesome results man! I need to talk you into trying out a MiniStick camshaft in place of that 231.237
![Happy](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_stretch.gif)
![Happy](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_stretch.gif)
__________________
Jason
Co-Owner, Texas Speed & Performance, Ltd.
2005 Twin Turbo C6
404cid Stroker, 67mm Twins
994rwhp/902lb ft @ 22 psi (mustang dyno) www.Texas-Speed.com
Jason
Co-Owner, Texas Speed & Performance, Ltd.
2005 Twin Turbo C6
404cid Stroker, 67mm Twins
994rwhp/902lb ft @ 22 psi (mustang dyno) www.Texas-Speed.com
#15
!LS1 11 Second Club
Thread Starter
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Thanks all!
A few notes:
This heads/cam combo has really woken up with this final round of bolt-ons.
Before, the TSP231/237 really pulled hard up top (as it should). I ran it cam-only at first, then with the TEA 1.5's. The addition of the heads bumped peak hp from 390 to 425, but the H/C combo still lacked low end, yet pulled like mad up top.
With the addition of the 85mm/90mm intake tract, and the HVMC LT's the engine now responds VERY STRONGLY across the ENTIRE rev range. It's like a new animal all together.
While this thread features the virtues of the FAST90/QTP HVM LT's bolt-ons, I must commend TSP and TEA for the kick *** nature of their internals. The ol', lazy 231/237 grind (one of the largest grinds available at the time) and these intro/budget heads (recommended to my by Brian from TEA when I was shopping around over a year ago, as I couldn't afford their Stage 2.5 LS6 heads) really perform.
I'll post up the graphs as soon as I can.
By the way, not only was this the same dyno, it was same tuner. I was told today that this car pulled the highest NA Heads/Cam 346ci numbers yet at Kelley Chevrolet (South Florida is not exactly Texas or Michigan when it comes to strong LS1 engine setups). And it's well known around these parts that their dyno is far from liberal.
A few notes:
This heads/cam combo has really woken up with this final round of bolt-ons.
Before, the TSP231/237 really pulled hard up top (as it should). I ran it cam-only at first, then with the TEA 1.5's. The addition of the heads bumped peak hp from 390 to 425, but the H/C combo still lacked low end, yet pulled like mad up top.
With the addition of the 85mm/90mm intake tract, and the HVMC LT's the engine now responds VERY STRONGLY across the ENTIRE rev range. It's like a new animal all together.
While this thread features the virtues of the FAST90/QTP HVM LT's bolt-ons, I must commend TSP and TEA for the kick *** nature of their internals. The ol', lazy 231/237 grind (one of the largest grinds available at the time) and these intro/budget heads (recommended to my by Brian from TEA when I was shopping around over a year ago, as I couldn't afford their Stage 2.5 LS6 heads) really perform.
I'll post up the graphs as soon as I can.
By the way, not only was this the same dyno, it was same tuner. I was told today that this car pulled the highest NA Heads/Cam 346ci numbers yet at Kelley Chevrolet (South Florida is not exactly Texas or Michigan when it comes to strong LS1 engine setups). And it's well known around these parts that their dyno is far from liberal.
#16
TECH Fanatic
iTrader: (4)
Join Date: Nov 2001
Location: West Palm Beach, Fl
Posts: 1,066
Likes: 0
Received 11 Likes
on
9 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech20year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Wow, I'm impressed! Don't think 123 mph trap speed in decent air will be a problem (assuming decent traction too). I've hit 122.9 with 438 rwhp at Moroso. I don't recall from your previous posts, did you port your intake? I want to install mine but haven't figured out what I should do about porting the intake.
#17
!LS1 11 Second Club
Thread Starter
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by Bill00Formula
Wow, I'm impressed! Don't think 123 mph trap speed in decent air will be a problem (assuming decent traction too). I've hit 122.9 with 438 rwhp at Moroso. I don't recall from your previous posts, did you port your intake? I want to install mine but haven't figured out what I should do about porting the intake.