Your typical "Guess my numbers!" thread :)
#1
TECH Resident
Thread Starter
iTrader: (7)
Join Date: Dec 2008
Location: CT
Posts: 796
Likes: 0
Received 0 Likes
on
0 Posts
Your typical "Guess my numbers!" thread :)
I am bored at work, so figured I'd throw a post up
I am finally getting my car back together after being apart and sitting in my driveway for over a year!
Last Thursday we got the engine all back together - 1st start up I wanted to ... We reused the LS7 lifters which apparently collapsed on the 1st start up from sitting for so long. It was SO LOUD! When we turned the car off we could hear the pushrods falling (little plinking noises). Today we received the Comp Cams Pro Magnums and Dual 3" Electronic cutouts for the y pipe! She should be running by the end of the week!
1999 Camaro Z28 M6
The mod list:
Stock Ls1 bottom end
Comp Cams Promagnum Lifters
Comp Cams hardened pushrods
Harland Sharp SLS17 Rockers
TSP Tsunami Cam (235/240 .648/.609 @ 111)
Stock 241 heads with springs and retainers
FAST 78mm intake manifold
80MM Throttle Body (forgot brand)
1 3/4 Pacesetter Longtubes
3" ORY pipe with dual Cutouts
Dynomax Intermediate pipe
Magnaflow muffler
Lid/K&N filter/Smooth Bellow/Descreened MAF
PCMforLess Mail Order tune by Bryan
Walbro 255 pump
FAST 60lbs Injectors
Hotwire kit
I had 28" tire and skinnies from my previous turbo setup and running the stock rearend on 3.42 gears
Just wondering what you guys think it will make on a Dynojet Mind you I am only about 45 - 55 ft above sea level in the CT river valley!
I am finally getting my car back together after being apart and sitting in my driveway for over a year!
Last Thursday we got the engine all back together - 1st start up I wanted to ... We reused the LS7 lifters which apparently collapsed on the 1st start up from sitting for so long. It was SO LOUD! When we turned the car off we could hear the pushrods falling (little plinking noises). Today we received the Comp Cams Pro Magnums and Dual 3" Electronic cutouts for the y pipe! She should be running by the end of the week!
1999 Camaro Z28 M6
The mod list:
Stock Ls1 bottom end
Comp Cams Promagnum Lifters
Comp Cams hardened pushrods
Harland Sharp SLS17 Rockers
TSP Tsunami Cam (235/240 .648/.609 @ 111)
Stock 241 heads with springs and retainers
FAST 78mm intake manifold
80MM Throttle Body (forgot brand)
1 3/4 Pacesetter Longtubes
3" ORY pipe with dual Cutouts
Dynomax Intermediate pipe
Magnaflow muffler
Lid/K&N filter/Smooth Bellow/Descreened MAF
PCMforLess Mail Order tune by Bryan
Walbro 255 pump
FAST 60lbs Injectors
Hotwire kit
I had 28" tire and skinnies from my previous turbo setup and running the stock rearend on 3.42 gears
Just wondering what you guys think it will make on a Dynojet Mind you I am only about 45 - 55 ft above sea level in the CT river valley!
Last edited by sujomatt; 06-28-2011 at 11:53 AM.
#3
TECH Resident
Thread Starter
iTrader: (7)
Join Date: Dec 2008
Location: CT
Posts: 796
Likes: 0
Received 0 Likes
on
0 Posts
Man I'd be the happiest guy in CT if i hit that # - My honest goal is just to make it over 400 lol
I dont know much about the FAST 78mm intake vs a FAST 90mm ... they essentially the same minus the throttle body size??
I dont know much about the FAST 78mm intake vs a FAST 90mm ... they essentially the same minus the throttle body size??
Last edited by sujomatt; 06-21-2011 at 03:32 PM.
Trending Topics
#8
TECH Resident
Thread Starter
iTrader: (7)
Join Date: Dec 2008
Location: CT
Posts: 796
Likes: 0
Received 0 Likes
on
0 Posts
Thx bro, that gives me some confidence she wont be a complete slouch!
I wanted a FAST 90 buuuut I didn't want to get a throttle body and a bigger MAF and all that jazz at the time which was wayyyyyy back in the day when I had a crappy job. This is only square one (again) right now!
I do plan on getting a FAST 102 and matching TB this winter. As well as a TSP MAF and FTP Lid. I'd like to see what I can do with that on stock flowing 241s. But we will see what life has in store for me in the meantime lol
I do plan on getting a FAST 102 and matching TB this winter. As well as a TSP MAF and FTP Lid. I'd like to see what I can do with that on stock flowing 241s. But we will see what life has in store for me in the meantime lol
#15
TECH Resident
Thread Starter
iTrader: (7)
Join Date: Dec 2008
Location: CT
Posts: 796
Likes: 0
Received 0 Likes
on
0 Posts
The car finally runs and drives. Just need the cutout relocated to a better spot, the subframe connector put on and have the mounts replaced with new poly mounts.. And then DYNO TIME!
#18
TECH Resident
Thread Starter
iTrader: (7)
Join Date: Dec 2008
Location: CT
Posts: 796
Likes: 0
Received 0 Likes
on
0 Posts
So I took it for a rip on an onramp - video below.
Looks better in 720p (HD)
http://www.youtube.com/watch?v=RYcda...e_gdata_player
Looks better in 720p (HD)
http://www.youtube.com/watch?v=RYcda...e_gdata_player