POWER from a D1
#22
12 Second Club
iTrader: (4)
Join Date: Aug 2003
Location: NorCal
Posts: 1,618
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
what size engine you have stock 346
what is you compression ratio approx 9.2:1 (6.0 heads stock)
what pulley sizes you are running ATI Dampner/4.25
intercooler you are running FMIC OBX
cam size 221/227 .580 114lsa
transmission stock M6
gears 3.70 9"
boost number 12psi @ 6500rpm
extras: Meth, Racetronix single pump, 60lb inj., JetHot LTs no cats.
Tuner: Tuned by Rick @ Synergy
Power: 651rwhp/558rwtq
Dyno: Dynapac Dyno
what is you compression ratio approx 9.2:1 (6.0 heads stock)
what pulley sizes you are running ATI Dampner/4.25
intercooler you are running FMIC OBX
cam size 221/227 .580 114lsa
transmission stock M6
gears 3.70 9"
boost number 12psi @ 6500rpm
extras: Meth, Racetronix single pump, 60lb inj., JetHot LTs no cats.
Tuner: Tuned by Rick @ Synergy
Power: 651rwhp/558rwtq
Dyno: Dynapac Dyno
#24
12 Second Club
iTrader: (4)
Join Date: Aug 2003
Location: NorCal
Posts: 1,618
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Im currently putting a FLT lvl4 4L80E with a Circle-D 4C and Rossler t-brake in it.
![Chug! Chug! Chug!](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_chug.gif)
#25
12 Second Club
iTrader: (19)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Last time I went it did 11.3 @ 128mph with a 1.6 60'.... however I had to wrestle the **** out of it to get 2nd gear to engage. The stock hydraulics REALLY did not like the 5k rpm drop off the line..... had no pedal for 2nd.
Im currently putting a FLT lvl4 4L80E with a Circle-D 4C and Rossler t-brake in it.![Chug! Chug! Chug!](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_chug.gif)
Im currently putting a FLT lvl4 4L80E with a Circle-D 4C and Rossler t-brake in it.
![Chug! Chug! Chug!](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_chug.gif)
#26
TECH Resident
iTrader: (2)
Join Date: Jul 2005
Location: Sparks,NV
Posts: 919
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Last time I went it did 11.3 @ 128mph with a 1.6 60'.... however I had to wrestle the **** out of it to get 2nd gear to engage. The stock hydraulics REALLY did not like the 5k rpm drop off the line..... had no pedal for 2nd.
Im currently putting a FLT lvl4 4L80E with a Circle-D 4C and Rossler t-brake in it.![Chug! Chug! Chug!](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_chug.gif)
Im currently putting a FLT lvl4 4L80E with a Circle-D 4C and Rossler t-brake in it.
![Chug! Chug! Chug!](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_chug.gif)
My apologies to the op I didnt mean to hijack your thread.
#31
10 Second Club
Thread Starter
iTrader: (13)
Join Date: Feb 2006
Location: MOREHEAD KY
Posts: 3,297
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
hay dean its good to see you on here! im sure that your car will do a least what mine did! let me know if you need any help with anything! and ggod luck with you car man!!
#32
TECH Resident
iTrader: (23)
Join Date: Oct 2008
Location: Rhode Island
Posts: 990
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
if you guys wouldn't mind adding onto the op's ?. with all these horsepower numbers what gears are ideal with 6500rpm shifts crossing the traps at the top of 4th? everyone should be close to run 9's or 9's capable. ill be getting a procharger soon to an wonder what gears are best for an m6.
#33
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
if you guys wouldn't mind adding onto the op's ?. with all these horsepower numbers what gears are ideal with 6500rpm shifts crossing the traps at the top of 4th? everyone should be close to run 9's or 9's capable. ill be getting a procharger soon to an wonder what gears are best for an m6.
#34
TECH Veteran
iTrader: (7)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
ok, somebody has to post low #'s, so it might as well be me
D1SC, 6.0 w/225/229, .580/.590 on a 114, Pat. stage 2 heads, Vic Jr intake with 750 blowthru carb, Proc. 3 core sheetmetal intercooler
488RWHP @ 9.6 psi under the carb @ 6200 rpm, 433 torq in my 3700 lb chevelle with a 4l80e, 28" M/T drag radials, 3.73 rear
i have run a best of 10.68 @ 126-i have beat some cars with 150 more RWHP, so what do the #'s really mean anyway-i just used the dyno to make sure the tune was good, plugs, timing, etc
my old car is all steel with full stock interior, just a street car, been together for almost 1 1/2 years, trouble free so far
ran it last week, just to test the trans, time was off, only 11.0 at 122, real bad air, felt car drop off near the end, plug ck was showing lean, so i didnt make any more passes-i dont run it much, first pass is always the slowest anyway-i forget the bottom pulley size, but i think the top is 4.25, i have a 4.0-i use a vette front drive/Procharger setup, built a 403 w/EPD cam, still sitting on the engine stand-prob more in the present setup, but it is what it is
D1SC, 6.0 w/225/229, .580/.590 on a 114, Pat. stage 2 heads, Vic Jr intake with 750 blowthru carb, Proc. 3 core sheetmetal intercooler
488RWHP @ 9.6 psi under the carb @ 6200 rpm, 433 torq in my 3700 lb chevelle with a 4l80e, 28" M/T drag radials, 3.73 rear
i have run a best of 10.68 @ 126-i have beat some cars with 150 more RWHP, so what do the #'s really mean anyway-i just used the dyno to make sure the tune was good, plugs, timing, etc
my old car is all steel with full stock interior, just a street car, been together for almost 1 1/2 years, trouble free so far
ran it last week, just to test the trans, time was off, only 11.0 at 122, real bad air, felt car drop off near the end, plug ck was showing lean, so i didnt make any more passes-i dont run it much, first pass is always the slowest anyway-i forget the bottom pulley size, but i think the top is 4.25, i have a 4.0-i use a vette front drive/Procharger setup, built a 403 w/EPD cam, still sitting on the engine stand-prob more in the present setup, but it is what it is
#35
8 Second Club
iTrader: (34)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
The F1A went 8.90s @ 153 at around 7300rpm with the 3.70/28" tires, I tried a 3.50 but the 60 foot dropped off a little.
But I also ran the car at low boost (5psi) to run 10.50 index classes here and there with the same 3.70 gear so its a good all around gear that is still streetable on a weekend car with a non OD trans.
#36
TECH Resident
iTrader: (23)
Join Date: Oct 2008
Location: Rhode Island
Posts: 990
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
kp what kind of cam were you using to be shifting at 7k? valvetrain? you have pretty much the same setup i'm shooting for.
hey bob, by any chance did you find the rest of the graph i was asking about in 2010 camaro section i believe is was a 402 with an f1a with an ep blower cam. what's the difference between the cam on that 402 and the ep blower cam used on the 346 or is it the same off the shelf one? everytime i think about that graph he makes me so hawny.
hey bob, by any chance did you find the rest of the graph i was asking about in 2010 camaro section i believe is was a 402 with an f1a with an ep blower cam. what's the difference between the cam on that 402 and the ep blower cam used on the 346 or is it the same off the shelf one? everytime i think about that graph he makes me so hawny.
#37
8 Second Club
iTrader: (34)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
kp what kind of cam were you using to be shifting at 7k? valvetrain? you have pretty much the same setup i'm shooting for.
hey bob, by any chance did you find the rest of the graph i was asking about in 2010 camaro section i believe is was a 402 with an f1a with an ep blower cam. what's the difference between the cam on that 402 and the ep blower cam used on the 346 or is it the same off the shelf one? everytime i think about that graph he makes me so hawny.
hey bob, by any chance did you find the rest of the graph i was asking about in 2010 camaro section i believe is was a 402 with an f1a with an ep blower cam. what's the difference between the cam on that 402 and the ep blower cam used on the 346 or is it the same off the shelf one? everytime i think about that graph he makes me so hawny.
#38
10 Second Club
iTrader: (24)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Update on my numbers, boost is the same, added 2* of timing.
396ci.
9.62:1
7.65 and 3.4
4.5" ATI Twins
AFR 205's
224/232 .581/.585 115LSA
4L60E with Vig. Triple Disc
3.73's in Moser 12 bolt, 33 spline axles
18-19 PSI
808.65 RWHP / 730.95RWTQ - No dyno tricks, on the street wheels. SAE, Smoothing 5.
396ci.
9.62:1
7.65 and 3.4
4.5" ATI Twins
AFR 205's
224/232 .581/.585 115LSA
4L60E with Vig. Triple Disc
3.73's in Moser 12 bolt, 33 spline axles
18-19 PSI
808.65 RWHP / 730.95RWTQ - No dyno tricks, on the street wheels. SAE, Smoothing 5.