365"-GT55-Holley EFI-Glide
#122
TECH Addict
Thread Starter
iTrader: (28)
Join Date: Sep 2008
Location: Deer park
Posts: 2,258
Likes: 0
Received 0 Likes
on
0 Posts
Racewire solutions will be doing the wiring on the car and will be converting my holley wiring harness to Mil Spec bulk head connectors on the firewall and i will also be using their awesome wiring board and custom switch panel with led dome light!
Some of the guys work, looks amazing.
https://www.facebook.com/media/set/?...1086782&type=3
Some of the guys work, looks amazing.
https://www.facebook.com/media/set/?...1086782&type=3
#124
TECH Addict
Thread Starter
iTrader: (28)
Join Date: Sep 2008
Location: Deer park
Posts: 2,258
Likes: 0
Received 0 Likes
on
0 Posts
Rick Stevens out of Santana Fe, TX. Great work and reasonable. I need to get it back over there for a few things hopefully he can make some room for me in a few weeks
#127
TECH Addict
Thread Starter
iTrader: (28)
Join Date: Sep 2008
Location: Deer park
Posts: 2,258
Likes: 0
Received 0 Likes
on
0 Posts
I actually went with strange DBL adjustable in the mean time. I went maybe 4x over my budget so I just went with these until I see that I am being held back by them. Mencers are about 1600 for a pair if I remember correctly. I would see myself upgrading the rear first when the time comes. 3200 is a whole lot of cash to spend on shocks.
#129
TECH Addict
Thread Starter
iTrader: (28)
Join Date: Sep 2008
Location: Deer park
Posts: 2,258
Likes: 0
Received 0 Likes
on
0 Posts
I am sending him the holley kit and all of the harnesses. He will be building a wiring board on a carbon sheet, converting the holley harness to mil spec connectors so I can disconnect it straight from the firewall, and a pre made harness for the fuel pump/fans/Air to water pump and all the other miscellaneous things that I will be running. The switch panel also has a harness with a mil spec connector that will go straight to the wiring board so it should be a simple install on my end.
#135
TECH Addict
Thread Starter
iTrader: (28)
Join Date: Sep 2008
Location: Deer park
Posts: 2,258
Likes: 0
Received 0 Likes
on
0 Posts
I didn't see the need for the dominator although I should have anyway. I can't use a traction control device, I don't need to control nitrous, meth, tranny etc. All I really need is the D/S sensor
#138
TECH Addict
Thread Starter
iTrader: (28)
Join Date: Sep 2008
Location: Deer park
Posts: 2,258
Likes: 0
Received 0 Likes
on
0 Posts
The hp is not any more or less better than the dominator. .. it just has more outputs. I looked at everything I was gonna use and it fit with the HP, if I were using meth, traction control and nitrous to spool then I would need the dominator but you don't need all that **** to run 4.60's
#140
Racewire solutions will be doing the wiring on the car and will be converting my holley wiring harness to Mil Spec bulk head connectors on the firewall and i will also be using their awesome wiring board and custom switch panel with led dome light!
Some of the guys work, looks amazing.
https://www.facebook.com/media/set/?...1086782&type=3
Some of the guys work, looks amazing.
https://www.facebook.com/media/set/?...1086782&type=3